• Journal of Biosystems Engineering
• /
• v.34 no.3
• /
• pp.167-174
• /
• 2009

This study was conducted to develop an agaricus bisporus washing machine which uses compressed air to remove foreign materials attached on the surface of agaricus bisporus. A prototype of the washing machine was constructed, and performance of removing foreign materials was tested. Research results are as follows: 1. Several transferring methods including PE roller rotation, brush roller rotation, PE screw rotation, vibration plate, and belt conveyor were evaluated. Roller, screw, and vibration methods caused damages on the surface of the products, but belt conveyor method caused the least damages. 2. For air jet, a stationary nozzle type and a rotational type were evaluated. The best air jet nozzle was the jet-type nozzle, and the rotational type was more effective than stationary type nozzle. 3. With the conveyer belt, box type moving method and the rotational air jet nozzle, the washing machine showed the best performance when higher than 5.4${\times}$105 Pa of air jet pressure and lower than 0.047 m/s of moving speed was used. Working performance of the system was 650 kg/h, and the damaging rate was 1.2 %.

• Asian-Australasian Journal of Animal Sciences
• /
• v.15 no.11
• /
• pp.1527-1530
• /
• 2002

Factor analysis was applied to the phenotypic correlation matrix of 15 linear type traits (scored linearly 1 to 50 points) for 2035 Holstein cows of 38 sires computed from data collected between 1988 and 1992 in Beijing Shuangqiao Farm and Beijing Xijiao Farm. The 15 linear type traits were stature, body strength, body depth, dairy form, rump angle, rump length, rump width, rear leg side view, foot angle, fore udder attachment, rear udder height, rear udder width, udder cleft, udder depth and teat placement rear view. The first four components accounted for 49.1% of the total variance in type scores. Factor 1 reflected strong cows, with deep bodies, with long and wide rumps, and tall in stature. Factor 2 reflected cows with well attached fore udders, wide rear udders and whose udders were supported by strong suspensory ligaments with close teat placement. Factor 3 reflected cows with good dairyness, sickled in the hocks, high rear udders and udder floors above the hocks. Factor 4 reflected cows with sloping rumps from hooks to pins and with steep foot angle. Principal component and factor analyses are useful to clarify the relationships among type traits.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.11
• /
• pp.1193-1201
• /
• 2013

Improved far field type(improved type) megasonic applicable to the cleaning equipment of single wafer processing type has been developed. In this study, to improve the uniformity of acoustic pressure distribution(APD), we utilize far field with relatively uniform APD, piezoelectric ceramic with a triangle hole in its center to prevent standing wave resulted from radial mode, and reflected wave from the wall of waveguide. On the basis of these methods, two analysis models of improved type were designed to which piezoelectric ceramic of different shape of electrode attached, and APD were analyzed by means of finite element method, and then one of them was selected by analysis results, finally, the selected model was fabricated. Test results show that the fabricated is better in the uniformity of APD than the imported and the conventional, also the fabricated shows high particle removal efficiency of 92.3% using DI water alone as a cleaning solution.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.38 no.5
• /
• pp.316-322
• /
• 2005

In order to develop a floating breakwater, which can efficiently control long period waves, vertical plates are attached in pontoon. Wave control and dynamic behaviors of the newly developed vertical plates type are verified from numerical analysis and hydraulic experiment. As a result, for the wave control and energy dissipation, the newly developed vertical plates type is more efficient than the conventional pontoon type. For the floating body motion, the wave transmission, depending on incident wave period, is decreased at the natural frequency. Dimensionless drift distance has similar trend of the reflection rate of wave transformation near natural frequency except maximum and minimum values. Dimensionless maximum tension is 17 percent of the weight of floating breakwater in case of the conventional pontoon type and 18 percent or 14 percent in case of the newly developed vertical plates type. Thus, it is shown that the wave control is improved by the vertical plates type. In addition, by adjusting the interval of the front and back vertical plate, we would control proper wave control.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2009.01a
• /
• pp.790-793
• /
• 2009

In the case of projection type display, it needs to use the screen in order to project the image clearly and wide viewing angle. We have been developing the step in type display system using the smoke screen. However, the image with smoke screen was flickered by gravity and air flow. Then we considered to reduce the flicker of the image and we found that flicker can be reduced and viewing angle becomes more large. This time we report the large viewing angle step in type display system using screen made up with very small particle size smoke and flow controlled nozzle. Hence, at first we considered the most suitable particle for the screen and then the shape of screen and then we constructed the array of flow controlled smoke screen. By the results of experiment we could get considerably high contrast flicker-less image and get the viewing angle more than $60^{\circ}$ by this flow controlled nozzle attached new type smoke screen and make clear the efficiency of this method.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.5
• /
• pp.407-413
• /
• 2013

This paper deals with the analysis of dynamic characteristics of mooring system of floating-type offshore wind turbine. A spar-type floating structure which consists of a nacelle, a tower and the platform excepting blades, is used to model the floating wind turbine and connect three catenary cables to substructure. The motion of floating structure is simulated when the mooring system is attached using irregular wave Pierson-Moskowitz model. The mooring system is analyzed by changing cable position of floating structure. The dynamic behavior characteristics of mooring system are investigated comparing with cable tension and 6-dof motion of floating structure. These characteristics are much useful to initial design of floating-type structure. From the simulation results, the optimized design parameter that is cable position of connect point of mooring cable can be obtained.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.1
• /
• pp.23-27
• /
• 2003

Structural properties of Cu-Ni alloy films, such as preferred orientation, crystallite size, in-ter-planar spacing, cross-sectional morphology, and electrical resistivity, are investigated in terms of tar-get configurations that are used in the film deposition by means of magnetron co-sputtering. Two different target configurations are considered in this study: a dual-type configuration in which two separate tar-gets (Cu and Ni) and different bias types (RF and DC) are used and a Ni-on-Cu type configuration in which Ni chips are attached to a Cu target. The dual-type configuration appears to have some advantages over the Ni-on-Cu type regarding the accurate control of atomic composition of the deposited Cu-Ni alloy. However, the dual-type-produced film exhibits a porous and columnar structure, the relatively large internal stress, and the high electrical resistivity, which are mainly due to the relatively low mobility of adatoms. The affects of thermal treatment and deposition conditions on the structural and electrical properties of dual-type Cu-Ni films are also discussed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.5
• /
• pp.39-44
• /
• 2011

Automatic fire alarm system is set up to automatically detect fire on buildings. Because of economic reasons, P-type receiver and a conventional type fire detector is normally used for automatic fire alarm system in Korea. Because early detection of fire is regarded as important, the need of finding technique of fire location increases. This paper is studied a method to improve a reliability and add a function of fire location detection on a conventional type fire detector and P-type receiver. Fire location is detected by a method that controller attached on the receiver and the detector is read with a time lag. A reliability of fire detection alarm system is improved with a method that false fire alarm is able to decrease using two different principle detector together. This paper is studied for basic data of improvement of low-cost addressable automatic fire alarm system.

• Clinics in Shoulder and Elbow
• /
• v.2 no.1
• /
• pp.41-46
• /
• 1999

Glenoid labrum acts as one of static stabilizer of the glenohumeral joint. It deepens the glenoid socket and may also serve as a chock, acting as a wedge in preventing glenohumeral translation. Two types of variations in labral anatomy were noted by Detrisac and Johnson. Type A has a superior labrum that is detached centrally but well attached peripherally. The type B labrum is well attached centrally and peripherally at all sites. A meniscoid-type labrum is thought to be normal unless there are splits or fragmentation of the overlying labral tissue. Meniscoid type labrum is different from SLAP II lesion in that it has a firm anchoring on the superior labrum. We observed four cases that had a meniscoid variant superior labrum, which covered the superior glenoid unusually larger than normal in the arthroscopic treatment of shoulder pathology including instability and rotator cuff diseases. We did arthroscopic reshaping and debridement of meniscoid variant superior labrum combined with pathologic change of the glenohumeral joint. Further study would be required for understanding the mechanism of the development of meniscoid variant labrum and its clinical significance.

• Journal of the Korean Society of Costume
• /
• v.55 no.4 s.94
• /
• pp.49-61
• /
• 2005

This study is to research the types and formation of the pieces for fastening the clothing in the western and oriental world from 18c to 19c. The pieces for fastening the clothing, depending on their formation, are classified as the ribbon type, the belt type, the button type, and the compound type. The ribbon type indicates fastening the clothing with the strips attached to the clothes. It is divided into the symmetry type and the asymmetry type by the looks of the ribbon alter it is tied. The belt type means fastening the clothing with a string or a belt, separated from the clothes. It is divided into the string type and the belt type. The button type is to fasten the clothing with buttons, button holes, and hooks. It is divided into the basic type, the wrapping type, and the knot type. The compound type is a mixture of two or three types out of the ribbon type, the belt type, and the button type. The pieces for fastening the clothing has aesthetic features as well as their functional characteristics. It has beautiful features like the harmonious beauty of Yin and Yen shown in the asymmetrical types, the beauty of spell wishing for health, long-life, wealth, wisdom, and so on, the beauty of decency showing the intention of refraining from exposing their body in public, the beauty of eroticism emphasizing the beauty of the human body, and the beauty of representing their social class, authority, affiliation, and so on.