• 한국산림과학회지
• /
• 제75권1호
• /
• pp.38-45
• /
• 1986

본 연구는 Juniperus chinensis 의 7 varieties와 Pinus densiflora의 한 변종에 대한 karyotype analysis의 결과로 다음과 같은 성적을 얻었다. 1) J. chinensis v. kaizuka, J. chinensis v. aureo-variegata와 J. chinensis v. procumbens 는 tetraploid 이다. 2) 각 수종의 염색체에 있어 긴 평균장과 긴 염색체를 많이 가지고 있는 수종은 J. chinensis와 J. chinensis v. aureo-globosa 이고 그 반대로 짧은 평균장과, 짧은 염색체를 가진 수종은 J. chinensis v. horizontalis 와 J. chinensis v. globosa 이다. 3) 각 염색체의 short arm에 대한 long arm의 평균비치가 큰 수종은 J. chinensis v. globosa 와 J. chinensis v. kaizuka 이고, 작은 수종은 J. chinensis v. aureo-globosa이다. 4) 염색체를 긴 순서로 배열할 때의 배열순서가 J. chinensis 의 배열상과 가장 근사한 수종은 J. chinensis v. sargentii, J. chinensis v. horizontalis, J. chinensis v. globosa 와 J. chinensis v. aureo-globosa이며, J. chinensis v. procumbens 는 배열상이 가장 다르다. 5) Pinus densiflora for. multicaulis는 염색체 평균장이 짧고, arm ratio 는 크다. 6) 염색체를 긴 순서로 배열할 시의 longarm 과 short arm의 배열순서가 6본의 염색체에서 같이 나타난다. 7) P. densiflora for. multicaulis는 secondary constriction이 많은 염색체에서 나타난다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권5호
• /
• pp.217-221
• /
• 2005

A inductive voltage divider(IVD) is widely used as a ratio arm of precise impedance measurement bridges at low frequencies of audio frequency range and a well fabricated IVD has ratio error of $10^{-7}$ order without any calibration. Recently, the order of $10^{-8}$ of the best measurement uncertainty is needed for calibration and maintenance of impedance standards as national standards. In order to achieve that uncertainty, the IVD which is used for a ratio arm of precise impedance measurement bridge should be calibrated within the uncertain of order of $10^{-8}$ For this purpose, a ratio calibration bridge for IVDs has been developed. The measurement uncertainties of both inphase and quadrature of the bridge are analyzed less then $3{\times}10^{-8}$ respectively at 1 kHz and 25 V.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.228-229
• /
• 2007

As one way of weight saving of the vehicle, 1-piece typed lower control arm has been developed using high strength hot rolled steel sheet. In order to overcome the edge splitting problem during edge flanging or burring process, HER (hole expansion ratio) value of steel sheet was primarily considered. The strength grade of steel sheet and the shape were optimized utilizing Taguchi method.

• Wind and Structures
• /
• 제35권2호
• /
• pp.93-108
• /
• 2022

Steel tubular towers are commonly used in UHV and long crossing transmission lines. By considering effects of the model scale, the solidity ratio and the ratio of the mean width to the mean height, wind tunnel tests under different wind speeds on twenty tubular steel tower body models and twenty-six tubular steel cross-arm models were completed. Drag coefficients and shielding factors of the experimental tower body models and cross-arm models in wind directional axis for typical skewed angles were obtained. The influence of the lift forces on the skewed wind load factors of tubular steel tower bodies was evaluated. The skewed wind load factors, the wind load distribution factors in transversal and longitudinal direction were calculated for the tubular tower body models and cross-arm models, respectively. Fitting expressions for the skewed wind load factors of tubular steel bodies and cross-arms were determined through nonlinear fitting analysis. Parameters for skewed wind loads determined by wind tunnel tests were compared with the regulations in applicable standards. Suggestions on the drag coefficients, the skewed wind load factors and the wind load distribution factors were proposed for tubular steel transmission towers.

• 한방재활의학과학회지
• /
• 제15권2호
• /
• pp.45-54
• /
• 2005

Objectives : This study aims to confirm the importance of behavior habit and exercise, especially leg exercise in obese. Methods : Out of 2247 people, we divided 1125 people in normal group(BMI<25) and 122 people in obese group($BMI{\geq}25$). We measured each arm, leg, abdomen muscle circumference and right and left water difference using BLA. We Investigated whether ratio of leg muscle circumference to arm and abdomen has differences by statistics between each groups. And analyzed correlation with BMI. We also investigated right and left water distribution difference of two group's limbs and the correlation with BMI. Statistical analysis was performed by using SPSS program. Results : 1. In obese group, ratio of leg muscle circumference to arm and abdomen is significantly lower than normal group(P<0.001). 2. Ratio of leg muscle circumference to arm and abdomen were negatively correlated with BMI(r-0.461, r=0.462, P<0.001). And partial correlation coefficient controlled for age and sex is -0.528, -0.632(P<0.001). 3. In the case of women, there was right and left water distribution difference as statistical in leg. In the case of Obese, the difference is serious. Conclusions : These results suggest that exercise and activity of lower limbs is more needed in the field of obesity treatment and prevention.

• 한국정밀공학회지
• /
• 제24권3호
• /
• pp.84-90
• /
• 2007

As a result of vehicle maintenance of rocker arm shaft for 4-cylinder SOHC engine, failure stress analysis of rocker arm shaft is needed. Because more than 30% of vehicles investigated have been fractured. Failure stress analysis is classified into an naked eyes, microscope, striation and X-ray fractography etc. Failure stress analysis by using striation is already established technology as means for seeking cause of fracture. But, although it is well known that striation spacing corresponds to the crack growth rate da/dN, it is not possible to determine ${\sigma}_{max}\;and\;{\sigma}_{min}$ under service loading only from striation spacing. This is because the value of striation spacing is influenced not only by ${\Delta}K$ but also by the stress ratio R. In the present paper, we determine the stress ratio using orthogonal array and ANOVA, and propose a prediction method of failure stress which is combined with FEM and striation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.523-527
• /
• 1991

A rubber pneumatic controlled actuator is a new actuator. It is very light With a high power-to-weight ratio. In this thesis, a control method for a two link robot arm using the rubber actuator is developed. The structure of the servo control is made up of two sections. The position control is performed by PID feedback control. The air pressure is controlled by Servo Valve Unit driven by PWM and the control input is compensated by software operation. The numerical simulation of this control method to two link robot arm is presented to verify the performance of the closed loop system. The actual control of the real two link robot arm with rubber actuator is taken and its results are discussed.

• 대한물리의학회지
• /
• 제15권1호
• /
• pp.77-84
• /
• 2020

PURPOSE: This study compared the activities of the trunk muscles during crutch walking to determine which of the crutch length measurements is most beneficial. METHODS: Twenty young women volunteered to participate in this study. After adjusting crutch length, the participants performed a three-point walking with nondominant leg limited in weight bearing. This study used six crutch length measurements: (1) Height-40.6cm, (2) Height'.77, (3) Olecranon-to-finger length, (4) Axillary-toheel length, (5) Arm-span length-40.6cm, and (6) Arm-span length'.77. The EMG activities of the internal oblique (IO), rectus abdominis (RA), multifidus (MF), and erector spinae (ES), muscles on the weight bearing side were monitored using wireless surface EMG. RESULTS: The EMG activities of the RA and ES appeared to be significantly different among the crutch length measurements (p<.05). The post-hoc test showed that the 'Arm-span length-40.6cm' was significantly greater in the RA activity when compared to the 'Height'.77' and 'Axillary-to-heel length' measurements, and in the ES activity when compared to 'Height'.77' measurements. Furthermore, IO/RA and MF/ES ratios showed significant differences among the crutch length measurements (p<.05). In the post-hoc test, significant difference was observed between 'Olecranon-to-finger length' and 'Arm-span length-40.6cm' for the IO/RA ratio, and between 'Height'.77' and 'Olecranon-to-finger length' and between 'Height'.77' and 'Arm-span length-40.6cm' measurement for the MF/ES ratio. CONCLUSION: These findings suggest that the 'Height'.77' measurement is relatively advantageous to optimize the activities of trunk muscles during the crutch walking, and allow simple measurements of the crutch length.

• Nutrition Research and Practice
• /
• 제9권3호
• /
• pp.268-277
• /
• 2015

BACKGROUND/OBJECTIVES: Although it is crucial to identify those children likely to be treated in an appropriate nutrition rehabilitation programme and discharge them at the appropriate time, there is no golden standard for such identification. The current study examined the appropriateness of using Mid-Upper Arm Circumference for the identification, follow-up and discharge of malnourished children. We also assessed its discrepancy with the Weight-for-Height based diagnosis, the rate of recovery, and the discharge criteria of the children during nutrition rehabilitation. SUBJECTS/METHODS: The study present findings from 156 children (aged 6-59 months) attending a supplementary feeding programme at Makadara and Jericho Health Centres, Eastern District of Nairobi, Kenya. Records of age, weight, height and mid-upper arm circumference were selected at three stages of nutrition rehabilitation: admission, follow-up and discharge. The values obtained were then used to calculate z-scores as defined by WHO Anthro while estimating different diagnostic indices. RESULTS: Mid-upper arm circumference single cut-off (< 12.5 cm) was found to exhibit high values of sensitivity, specificity, positive predictive value, negative predictive value, positive likelihood ratio, negative likelihood ratio at both admission and discharge. Besides, children recorded higher rate of recovery at 86 days, an average increment of 0.98 cm at the rate of 0.14mm/day, and a weight gain of 13.49gm/day, albeit higher in female than their male counterparts. Nevertheless, children admitted on basis of low MUAC had a significantly higher MUAC gain than WH at 0.19mm/day and 0.13mm/day respectively. CONCLUSIONS: Mid-upper arm circumference can be an appropriate tool for identifying malnourished children for admission to nutrition rehabilitation programs. Our results confirm the appropriateness of this tool for monitoring recovery trends and discharging the children thereafter. In principle the tool has potential to minimize nutrition rehabilitation costs, particularly in community therapeutic centres in developing countries.

• 한국컴퓨터정보학회:학술대회논문집
• /
• 한국컴퓨터정보학회 2014년도 제49차 동계학술대회논문집 22권1호
• /
• pp.9-13
• /
• 2014

The performance of large scale software applications has been automatically increasing for last few decades under the influence of Moore's law - the number of transistors on a microprocessor roughly doubled every eighteen months. However, on-chip transistors limitations and heating issues led to the emergence of multicore processors. The energy efficient ARM based System-on-Chip (SoC) processors are being considered for future high performance computing systems. In this paper, we present a case study of two widely used parallel programming models i.e. MPI and MapReduce on distributed memory cluster of ARM SoC development boards. The case study application, Black-Scholes option pricing equation, was parallelized and evaluated in terms of power consumption and throughput. The results show that the Hadoop implementation has low instantaneous power consumption that of MPI, but MPI outperforms Hadoop implementation by a factor of 1.46 in terms of total power consumption to execution time ratio.