• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.5
• /
• pp.419-426
• /
• 2000

Generally diode rectifier has been used as Preregulator of arc- welding machine. Its defect is the generation of high current harmonics which result In utility pollution. In this parer, using the three-phase PWM converter, the input performance of arc-welding machine is improved by increasing the input power factor. When the diode rectifier in the arc-welding machine is replaced with three-phase PWM converter, PWM converter should control DC voltage of the output side. If PI controller is used for the output DC voltage regulator, the output DC voltage has high ripple voltage due to the instantaneous load variation in the arc-welding machine. In this paper, the feedforward compensator has been introduced to reduce the DC voltage ripple. It lessens the influence of load current which is the disturbance of the output DC voltage regulator. Theoretical prediction of this analysis has been verified by comparing with experimental data

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.2
• /
• pp.128-137
• /
• 1999

Recently the pelionnance of CO2 arc welding machine has been advanced significantly through the adoption of i invelter circuit topology. which made it possible to improve welding perfonnances such as spatter generation and bead s state. But the conventional inverter arc welding machine generates constant output voltage which cause much spatter g generation dUling short-circuit and arc start time because it is unable to control output current instantaneously. So this p paper representes wavefCnm controlled inverter arc welding machine which control the wavefonn of welding current and t thus to suppress the spatter generation. And the system designed in this paper is the digital controller using single chip m microprocessor of 80C196KC. As a result of perfonnance test for this system, the spatter generation is reduced and s shOlt-circuit time period is stabilized compared to conventional one. And more by using switched mode rectifier for A AC/DC power convelter. unity power factor is maintained and low order halmonic spectrum is supressed.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.1012-1016
• /
• 1998

According to the adoption of inverter circuit topology for welding machine area, the improvement of welding performance can be achieved. However conventional CO2 inverter arc welding machine uses the constant voltage characteristics. So the metal transfer is performed under unoptimum condition in the sence of spatter generation. In this paper the new control algorithm is proposed for welding machine, which is the instantaneous output current control method using single chip microprocessor. But the optimum waveform of welding current is still uncertain, as a first step for figuring out the optimized waveforms, this study was performed. And as a result of performance test of the proposed system, it was demonstrated that all of the waveform variation parameter could be set individually and the generated spatter is reduced compared to conventional inverter arc welding machine.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.5
• /
• pp.110-117
• /
• 2004

In automatic welding process using a robot, seam tracking is one of the important parts. Sensor for seam tracking is divided broadly into two categories as non contact sensor and contact sensor. The arc sensor is one of the non contact sensors, and it can be applied in weaving arc and rotating arc welding process. In such the arc sensors, rotating arc sensor can be applied to high speed welding over tens of Hz. The decrease of self regulation by high rotating speed causes to improve accuracy and response of sensor. In this study, fuzzy controller was used to track the seam for the $CO_2$ arc welding which had unstable arc. It could be shown that the rotating arc sensor was better than the weaving arc sensor.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.62-67
• /
• 1998

An arc welding machine using single switched PFC converter is presented in this paper. First, the basic operation and principle is reviewed. Controller design is intended to force voltage ripple to minimize, and dynamic response to enhance, Feed-forward strategy for arc welding machine is developed, and that is verified by simulation. The improved power factor characteristics of arc welding machine known as low power factor system with nonlinear property, are shown and evaluated compared to conventional one.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.170-173
• /
• 2002

The object of this study is to investigate the effect of compounded welding through the AE (Acoustic Emission) characteristics on static tensile test. This study was carried out a SM 490A, high tension steel using the low hydrogen type E4316 of electronic shield metal arc welding and compound wire of $CO_2$gas arc welding. $CO_2$welding, weak in the intensity of HAZ (Heat Affected Zone), can be improved by being combined with coated arc welding, Coated arc welding, weak in the intensity of the bead, can be improved by being combined with $CO_2$welding. Especially, electronic coated arc welding and $CO_2$welding complement the mechanical intensity of HAZ and the bead with each other. So, compounded welding increases the intensity in the special parts and enhances the quality of goods.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.166-170
• /
• 1998

The metal transfer of CO2 arc welding machine can be devided into short-circuit(low current) metal transfer. Especially in large crrent region, the main problem of CO2 arc welding machine is much spatter generation which is caused by mainly instant short-circuit matal transfer. So in this paper descrives new current control method in large current region, which can improve welding performance and lessen spatter generation. And as a result of experiment, the effect of proposed control method is demonstrated.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.180-184
• /
• 1998

Recently the performance of CO2 arc welding machine has been advanced significantly through the adoption of inverter circuit topology which made it possible to control the waveform of welding current and thus to suppress the spatter generation. However, the optimum waveform is still uncertain. As a first step for figuring out the promising waveforms, this study was performed to set-up the experimental system for studying the effect of waveform variables. The overal system is controlled digital controller using single chip microprocessor of 80C196KC. As a result of performance test of this system, it was demonstrated all of the waveform variables could be set individually and the generated spatter is reduced compare to conventional inverter arc welding machine.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.2
• /
• pp.92-98
• /
• 1998

With the development of semiconductor devices, adoption of microcontroller prevails in industrial area. But in are welding industry, there has not been much progress in adoption of microcontroller technology. Therefore, this paper shows the application of digital control technology to welding machine. This paper presents the design of microcontroller that is appropriate for three phase $CO_2$ gas metal are welding machine. By using microcontroller in $CO_2$ gas metal are welding machine, the overall cost can be reduced compared to analog comtroller. Also TMS370C850 microprocessor is used as overall microcontroller for the are welding machine.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.4
• /
• pp.113-120
• /
• 2004

The object of this study is to investigate the effect of compounded welding through the AE(Acoustic Emission) characteristics for weld HAZ(Heat Affected Zone) under the static tensile test. This study was carried out an SWS 490A, high tension steel for electric shield metal arc welding(SMAW), $CO_2$ gas arc welding and TIG welding. Data displays are based on the measured parameters of the AE signals, along with environmental variables such as time and load. The accumulated AE event curve of HAZ definitely have the point of inflection subject to tensile test. The results of the tensile test of HAZ come out electric shield arc welding ＞$CO_2$ gas arc welding＞TIG welding in case of single welding, but generally the tensile test of HAZ come out electric shield arc welding＞ TIG welding ＞ $CO_2$ gas arc welding. These history plots give us useful and powerful information to analyze the results of material evaluation testing.