• Tribology and Lubricants
• /
• 제34권3호
• /
• pp.107-114
• /
• 2018

This paper presents a computational model of a gas foil journal bearing with shim foils between the top foil and bumps, and predicts its static and dynamic performance. The analysis takes the previously developed simple elastic foundation model for the top foil-bump structure and advances it by adding foil models for the "shim foil" and "outer top foil." The outer top foil is installed between the (inner) top foil and bumps, and the shim foil is installed between the inner top foil and outer top foil. Both the inner and outer top foils have an arc length of $360^{\circ}$, but the arc length of the shim foil is shorter, which causes a ramp near its leading edge in the bearing clearance profile. The Reynolds equation for isothermal and isoviscous ideal gas solves the hydrodynamic pressure that develops within the bearing clearance with preloads due to the ramp. The centerline pressure and film thickness predictions show that the shim foil mitigates the peak pressure occurring at the loading direction, and broadens the positive pressure as well as minimum film thickness zones except for the shortest shim foil arc length of $180^{\circ}$. In general, the shim foil decreases the journal eccentricity, and increases the power loss, direct stiffness, and damping coefficients. As the shim foil arc length increases, the journal eccentricity decreases while the attitude angle, minimum film thickness, and direct stiffness/damping coefficients in the horizontal direction increase.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.266-271
• /
• 2006

Characteristic of partial oxidation of methane using arc-jet plasma by AC power is investigated. Arc-jet reactor used in this work is slightly modified from typical arc jet reactor so that it can make and sustain stable state of plasma. Methane conversion, selectivity of chemicals such as hydrogen and hydrocarbon materials in the product are analyzed. Parametric approach on the performance of the reactor or detail on the partial oxidation process is carried with $O_2/C$ ratio as parameter. In addition to the results, SED and arc length is changed to understand the effect of current-voltage correlation on the reforming performance and relative role of thermal process.

• 한국멀티미디어학회논문지
• /
• 제10권12호
• /
• pp.1601-1611
• /
• 2007

In this paper, we presented geometric CAD watermarking scheme for Architectural design drawings using line, arc, and circle components to prevent infringement of copyright from unlawfulness reproductions and distribution. The conventional CAD watermarking scheme can be applied to both line and arc components. But the proposed scheme consists of line, arc and circle watermarking schemes for three basic components of CAD design. After extracting line, arc and circle components from designed drawing, the watermark is embedded into the length of Line component, the angle of arc component, and the radius of circle component considering the robustness against various geometric transformations. The embedding strengths in each component are determined to be preserving the transparency of the watermark. By experimental result, we confirmed the robustness and the invisibility of embedded watermarks in several conversions of architectural design drawing.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.1661-1666
• /
• 2009

This paper is analyzed the effect on characteristics of thrust force of linear induction motor(LIM) by arc type tester. Many kinds of tester have a rotational shape because of a finite length of railroad. Whereas effects by using rotational type tester are generally unknown. For reason of that, this paper is analyzed the effect on characteristics by rotational type tester using 2D finite element method(FEM), and then is compared a thrust force between linear type tester and rotational type tester. Analysis model is decided by numerical modeling for fitting the LIM for propulsion system of light rail, and it is changed to proper arc model. And then we analyzed the arc and the linear model. Consequently, arc type tester is not only useful experiment but also efficient simulation method, and small error is occurred between linear and arc model.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.90-95
• /
• 2013

Pipe inside clad welding is mainly used to the flow pipe of sub-sea or chemical plant. For the inside clad welding to the medium pipe with the diameter of about 12", TIG welding is frequently applied with filler metal. In this case, the clad welding has the very broad weld area over $10m^2$. And, the non-destructive test (NDT) such as ultrasonic test (UT) or radiographic testing (RT) should be conducted on the broad weld area, and it costs very high due to the time-consuming work. Therefore, the present study investigated the variation of arc voltage to develop the in-line quality monitoring system for the pipe inside TIG cladding. The 4 experimental parameters (current, arc length, wire feed position, and shield gas flow rate) varied to observe the change of arc voltage and to establish the model for the monitoring. The arc voltage was decreased when the wire was fed to the backward eccentric position(over 2mm), and the shield gas flow rate was insufficient under 10L/min. In the case of the backward eccentric position over 2mm, the bead appearance was not good and the dilution ratio was increased due to deep penetration. When the shield gas flow rate was lower than 10L/min, the bead surface was oxidized.

• 한국경영과학회지
• /
• 제16권2호
• /
• pp.103-117
• /
• 1991

Two important sensitivity issues over shortest path problems have been discussed. One is the problem of updating shortest paths when nodes are added and when the lengths of some arcs are increased or decreased. The other is the problem of calculating arc tolerances, that is the maximum increase of decrease in the length of a single arc without changing a given optimal tree. In this paper, assuming that there exists a parameter of interest whose perturbation causes the simultaneous changes in arc lengths, we find the invariance condition on these simultaneous changes such that the shortest path between two specified nodes remains unchanged.

• 전기의세계
• /
• 제29권6호
• /
• pp.401-409
• /
• 1980

This paper deals with the implementation of forced reclosing the transmission line. Because the ground circuit breaker method decrease the secondary arc current sufficiently, the reclosing time can be reduced. As the secondary arc current is large and its residual time is long in UHV transmission line, this method is more effective in that system. The resistance of ground circuit breaker which minimize the secondary arc current is determined according to the system voltage and the length of transmission line.

• Journal of Welding and Joining
• /
• 제8권3호
• /
• pp.60-69
• /
• 1990

Plasma arc cutting is a fusion cutting process in which a gas-constricted arc is employed to produce a high-temperature, high-velocity plasma jet on the workpiece. This process provides some advantages such as increased cutting velocity, excellent working accuracy and the ability to cut special materials (widely used stainless steels and Al-alloys, for example), when compared with iconventional oxyfuel gas cutting. From the view point of price and reliability of the power source, plasma arc cutting has also some distinct advantages over laser beam cutting. High-speed machines with NC or CNC systems are needed for the plasma arc or laser beam cutting process, while for oxyfuel gas cutting, low-speed machines with copying templates or optical-shape tracking sensors can be applied. The low price and high flexibility of the microprocessor arc contributing more and more the application of CNC system in the plasma arc cutting process, as in other manufacturing fields. From these points of view, a microprocessor-based plasma arc cutting system was developed by using a reference-pulse system, and its performance was tested. The interpolating routines were programmed in the assembly language for saving the memory volume and improving the compouting speed, which has an intimate relationship with the available cutting velocity.

• 대한인간공학회지
• /
• 제33권4호
• /
• pp.299-311
• /
• 2014

Objective: The aim of this study was to develop a method for measuring breast size from three-dimensional (3D) body scan image data. Background: Previous bra studies established reference points by directly contacting the subject's naked skin to determine the boundary of the breast. But some subjects were uncomfortable with these types of measurements. This study examined noncontact methods of extracting breast reference points from 3D body scan data that were collected while subjects were wearing standardized soft bras. Method: 3D body scan data of 32 Korean women were analyzed. The subjects were selected from the Size Korea 2010 study. The breast landmarks were identified by graphic analyses of slicing contour lines on 3D body scan data. Results: Three methods determining bra cup size were compared. The M1 and M2 methods determined cup size by calculating the difference between bust girth and under-bust girth. The M3 method determined bra cup size by measuring breast arc length. Conclusion: The researchers proposed an anthropometric bra cup sizing system with the breast arc length (M3 method). It was measured from the geometrically defined landmarks on the 3D body scan slicing contour lines. The new bra cup size was highly correlated with breast depth. Application: The noncontact measuring method used in this study can be applied to the ergonomic studies measuring sensitive body parts.

• 한국도로학회논문집
• /
• 제16권2호
• /
• pp.99-106
• /
• 2014

PURPOSES : This study is to develop Right-Turning Channelization Design Models of Semitrailer at Intersections by regression of vehicle tracking simulation. METHODS : Based on the literature review, it was indicated that right-turning channelization design guide of semitrailer is too complex and is not reflected turning speed and approach angle. To verify effectiveness of right turning semitrailer trajectories according to the changing turning speed and approach angle, vehicle tracking simulation was executed. And then, simulation results were analyzed for modeling design elements; minimum turning radius, swept path width, arc length, width of triangle island, of right-turning channelization using regression methods. RESULTS : When the turning speed is getting higher, minimum turning radius, arc length, width of triangle island increased and the approach angle lower, swept path width, arc length, width of triangle island reduced. The turning radius completely reflected by turning speed. CONCLUSIONS : In this research, it was investigated how much design elements are changed according to the turning speed and the approach angle of semitrailer. The developed right-turning channelization design models can help engineers to easy and comfortable design at various conditions.