• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.373-375
• /
• 2000

By DC load flow approximation, we analyzed marginal cost that is the important factor of price signal for network congestion management and expressed as a function of load. In network congestion, a large scale electric network is partitioned into subnetwork to provide a effetive price signal through zonal pricing. We propose a new network partition technique using marginal cost sensitivity with a variety of load consumption.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.906-909
• /
• 2005

In this study, the dynamic flying characteristics of the worn head sliders are investigated theoretically due to the change in head geometry caused by head and disk contact. The film shapes can be approximated as taper- truncated cycloidal-flat film. Two-dimensional time dependent modified Reynolds equation included molecular slip effect are formulated with neglected the roughness effect. The motion of head slider was assumed to have two degree of freedom in this work. Finite difference approximation with Newton Raphson iterative technique and the fourth order Runge-Kutta method were implemented to obtain the transient response of the slider head with various change in head geometry numerically and compared with the transient response of the IBM3380 type head slider. The simulation results show the film shape has affects significantly on the static and dynamic characteristic of slider head in magnetic storage systems.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.08a
• /
• pp.37-44
• /
• 2004

Continuous depth data are often required in applications of both onboard systems and maritime simulation. But data available are usually discrete and irregularly distributed. Based on the neuron network technique, methods of interpolation to the charted depth are suggested in this paper. Two algorithms based on Levenberg-Marquardt back-propaganda and radial-basis function networks are investigated respectively. A dynamic neuron network system is developed which satisfies both real time and mass processing applications. Using hyperbolic paraboloid and typical chart area, effectiveness of the algorithms is tested and error analysis presented. Special process in practical applications such as partition of lager areas, normalization and selection of depth contour data are also illustrated.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.116-120
• /
• 1989

The optimal control problem of linear Lumped Parameter Systems (LPS) and Distributed Parameter Systems (DPS) is studied by employing the technique of Walsh functions (WF). By the using the elegant operational properties of WF, a direct computational algorithm for evaluating the optimal control and trajectory of LPS and DPS is developed. Without the need of solving the traditional matrix Riccati equation, the WF approach in shown very simple in form and convenient for use of a computer. The approximation is in the sense of least squares employing WF as the basis and the results are in the piecewise constant and discrete form.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.187-194
• /
• 2010

Shape optimization of an upper plenum of PBMR type gas cooled nuclear reactor has been performed by using three-dimensional Reynolds-Averaged Navier-Stokes (RANS) analysis and surrogate modeling technique. The objective function is defined as a linear combination of uniformity of flow distribution in the core and pressure drop in the upper plenum and the core. The ratio of thickness of slot to diameter of rising channels, ratio of height of upper plenum to diameter of rising channels, and ratio of eight of the slot at inlet to outlet, are used as design variables for optimization. Design points are selected through Latin-hypercube sampling. The optimal point is determined through surrogate-based optimization method which uses 3-D RANS analyses at design points. The results show that the optimum shape represent remarkably improved performance in flow uniformity and friction loss than the reference shape.

• Journal of computational fluids engineering
• /
• v.15 no.3
• /
• pp.16-23
• /
• 2010

Shape optimization of an upper plenum of a PBMR type gas cooled nuclear reactor has been performed by using three-dimensional Reynolds-Averaged Navier-Stokes (RANS) analysis and surrogate modeling technique. The objective function is defined as a linear combination of uniformity of flow distribution in the core and pressure drop in the upper plenum and the core. The ratio of thickness of slot to diameter of rising channels, ratio of height of upper plenum to diameter of rising channels, and ratio of height of the slot at inlet to outlet, are used as design variables for optimization. Design points are selected through Latin-hypercube sampling. The optimal point is determined through surrogate-based optimization method which uses 3-D RANS analyses at design points. The results show that the optimum shape represent remarkably improved performance in flow uniformity and friction loss than the reference shape.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.491-496
• /
• 2003

In sensitivity analysis, semi-analytical method(SAM) reveals severe inaccuracy problem when relatively large rigid body motions are identified for individual elements. Recently such errors of SAM resulted by the finite difference scheme have been improved by the separation of rigid body mode. But the eigenvalue should be obtained first before the sensitivity analysis is performed and it takes much time in the case that large system is considered. In the present study, by constructing a reduced one from the original system, iterative method combined with mode decomposition technique is proposed to compute reliable semi-analytical design sensitivities. The sensitivity analysis is performed by the eigenvector acquired from the reduced system. The error of SAM caused by difference scheme is alleviated by Von Neumann series approximation.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.137-142
• /
• 2001

Since recent production system becomes that of the small quantity, large volume with high quality production, accurate and high speed inspection system is required. In such situation, noncontact 3D measurement system which utilized CCD cameras is useful technique in terms of system cost, speed of data acquisition, measuring accuracy and application. However, it has low accuracy compared with contact 3D measurement system because of the camera distortion, non uniformity of laser distribution and so on. For those reasons, in this paper precision enhancement method is studied considering radial camera distortion, and laser distribution. A distortion correction method is applied even to the standard lens. The laser slit beam trajectory is determined by 3 method: based of the Gaussian function signal approximation, the median method, the center of gravity method and the peak point of the Gaussian function method.

• Journal of applied mathematics & informatics
• /
• v.33 no.1_2
• /
• pp.77-87
• /
• 2015

Parallel lines are often used to increase production rate in many manufacturing systems where the main line splits into several lines in parallel, and after some operations, they merge into a main line again. Queueing networks with finite buffers have been widely used for modeling and analyzing manufacturing systems. This paper provides an approximation technique for multi-server two-stage networks with merge configuration and blocking which will be a building block for analysis of general manufacturing systems with parallel lines and merge configuration. The main idea of the method is to decompose the original system into subsystems that have two service stations with multiple servers, two buffers and external arrivals to the second stage are allowed. The subsystems are modeled by level dependent quasi-birth-and-death (LDQBD) process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.426-429
• /
• 2001

Many various products are manufactured which have sculptured surfaces recently. Constructing surface of these models is required technique called reverse engineering. In reverse engineering, a product which has sculptured surfaces is measured and we create surface model to acquire complete model data of object. Measured point data needs preprocess and sampling. Next a set of point data in a plane fit section curve. At last, surface is generated by fitting to section curves. Here we uses sweep surface. Sweep surface is compatible fitting CAD model to drawing. This paper discusses converting approximation of NURBS surface as a standard surface.