• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09b
• /
• pp.1179-1180
• /
• 2005

To immobilize the pollutants from wastewater in situ, two phosphatic clays collected from different areas in Egypt (eastern and western Sebaia, Aswan-Isna, Upper Egypt) used to remove contaminant ions from industrial wastewater. Obtained results confirmed the strong relationship between phosphatic clay and Pb elimination from wastewater. The sensitivity classification of phosphatic clay toward ions retained as described in three categories: highly sensitive to retain Pb , Al and Cr ; moderately sensitive for Mn; and weakly sensitive for Band Zn. Data suggested that large fraction of Pb removed by phosphatic clays stayed intact under a wide variation in extracting solution pH (3-11). In situ immobilization is considered a promising technique that has the potential to remove contaminant ions from wastewater. Two important factors need to be considered when applying this technique: The first, is the clay must be effective and selective under different composition of wastewater. The second, is the immobilized ions should be stable and non-leacheable under varying water conditions. Phosphatic clays with $Pb^{2+}$ were suitable to achieve these two factors. Possible mechanism for removal $Pb^{2+}$ by phosphatic clays is the formation of fluoropyromorphite through the dissolution of fluoro and hydroxyl apatite by its precipitation from solution, beside, Pb complexation at phosphatic clay surface at P-OH sites.

• Journal of the Mineralogical Society of Korea
• /
• v.9 no.1
• /
• pp.43-53
• /
• 1996

The detailed crystal chemistry of ilmenite from the Hadong massif was studied by the EPMA, M ssbauer spectroscopy, and Rietveld structural refinement using X-ray powder diffraction data. The ilmenite-bearing anorthosite shows complicated mineral assemblage which consists of plagioclase, clinopyroxene, hornblende, biotite, chlorite, apatite, allanite, and zircon. Anorthite is andesine in composition (Ab 28-57), and clinopyroxene drops in ferro-hypersthene (Fs 62-70). Ilmenite is trigonal symmetry with R space group, whose structure shows the alternation of Fe2+ (M1 site) octahedral layer and Ti (M2 site) layer along c axis. M ssbauer spectroscopy indicates that there are three doubles which assigned to couple of Fe2+($\delta$=0.812, 0.890mm/sec) and one Fe3+($\delta$=0.303mm/sec) in octahedral sites. Their Fe3+/$\Sigma$Fe is 0.065 and chemical formula is established as Fe2+0.94Fe3+0.07Ti0.97O3 using both EPMA and M ssbauer analysis. Rietveld structural refinement reveals that site occupancies of Fe in M1 and Ti in M2 are 91.2% and 89.4%, respectively. This implies that Ti and Fe2+ are alternatively occupy M1 and M2 sites. In addition, smaller M2 site is more preferable to Fe3+ occupancy over M1.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.3
• /
• pp.788-792
• /
• 2013

A shortcoming of using transmission electron microscopy (TEM) for structural analysis via electron diffraction is the relatively large error of the measurements as compared to X-ray diffraction. To reduce these errors, various internal standard methods from earlier studies have been widely used. We developed a new device to facilitate the application of internal standard methods in preparation of TEM grids used for nanopowder analysis. Through the application of a partial mask on the TEM grid, both the internal standards and the research materials can be loaded on the same grid. Through this process, we conducted a TEM analysis that compared synthetic hydroxyapatite (HAp) nanopowder to bone apatite from a bovine femur. We determined that the accuracy of the d-spacing measurements of the HAp and bone powders could be improved to better than 1% after statistical treatments of the experimental data. By applying a quarter mask, we loaded four different nanoparticles on a single TEM grid, with one section designated for the internal standard.

• Journal of Environmental Science International
• /
• v.19 no.2
• /
• pp.255-260
• /
• 2010

A stabilization/solidification (S/S) process for lead (Pb) contaminated soils was evaluated using waste cow bone containing apatite like compounds. Soil samples obtained form firing range were treated with waste cow bone. The effectiveness of stabilization was evaluated based on the Korean Standard Leaching Test (KSLT) and soil pH. The leached concentration reduced with increased in dose of waste cow bone. Overall, the KSLT results showed that Pb concentration in soils are significantly affected by amount of waste cow bone. When soil amended with 20 % of waste cow bone, less than 0.1 mg/kg was leached, and soil pH was increased from 6.5 to 8.4. Same results were obtained when finer waste cow bone was applied. The reachable concentration of Pb in soil showed in inversely proportional to solid/liquid ratio. Aging periods indicate improving mix design was applied. Relatively high lead concentrations was observed at the first 1 days, however leaching profile are reduced significantly over time for all mix designs.

• Journal of Technologic Dentistry
• /
• v.26 no.1
• /
• pp.77-88
• /
• 2004

Glass ceramics for dental crown prosthesis were prepared by crystallization of CaO-MgO-SiO2-P2O5-TiO2 glasses. Their crystallization behaviors have been investigated as a function of heattreatment temperature and holding time in relation to mechanical properties. The results are as follows: Vickers hardness and bending strength of glass ceramics increased due to the precipitation of apatite, whitlockite, $\beta$-wollastonite, magnesium titanate, and diopside crystal phases within glass matrix. The final crystalline phase assemblages and the microstructures of the glass ceramics were found to be dependent on heat-treatment temperature and holding time. Vickers hardnes and bending strength of glass ceramics increased with increasing heat-treatment temperature and holding time.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.4
• /
• pp.63-67
• /
• 2016

Divalent europium-activated $Ca_2PO_4Cl$ phosphor powders were prepared by a chemical synthetic method followed by heat treatment in reduced atmosphere, and the crystal structures, morphologies and photoluminescence properties of the powders were investigated by x-ray powder diffraction, scanning electron microscope and spectrometer. The effect of Ca/P mole ratio at the starting materials on the final products was evaluated. The optimized synthesis condition obtained in this study was Ca/P mole ratio of 2.0. The present phosphor materials had higher photoluminescence intensity and better color purity than the commercial blue phosphor powders, $(Ca,Ba,Sr)_{10}(PO_4)_6Cl_2:Eu^{2+}$. The result of excitation spectrum measurement indicated that the excitation efficiency of the synthesized powders was higher for the long-wavelength UV region than that of the commercial phosphor. It was thus concluded that the samples prepared in this study can be successfully applied for the light-emitting devices such as LED excited with long-wavelength UV light sources.

• Advances in materials Research
• /
• v.2 no.3
• /
• pp.155-172
• /
• 2013

The study of the corrosion inhibition of armatures made of steel conceived for reinforced concrete by sodium phosphate is the aim object of our experimental tests. Gravimetric and electrochemical measurements were carried in three different Mediums contaminated by chlorides (3% NaCl) with addition of increasing concentrations of sodium phosphate. Inhibitory efficiency reached 80% at an optimal concentration of $7,5{\times}10^{-3}M$, the results obtained using the gravimetric measurements are in good agreement with those obtained by electrochemical methods. However, the monitoring of the pH evolution after 24h shows in the three studied environments, that the pH decreases slightly at 24 hours from the initial pH at $t_0$, due to the presence of corrosion products which change the state of the final solution. Also, scanning electron microscopy revealed the existence of layers of apatite on the metal surface previously treated with the sodium phosphate which confirms the formation of a protective film around the surface of the metal.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.26 no.2
• /
• pp.179-185
• /
• 2000

The purpose of this study was to develop an osteogenic, biodegradable material using polymer and BMP. It was designed to have structural function and be moldable, for the reconstruction of load bearing areas and deformities of various configurations. Bone apatite was added to Poly(L-lactide)(PLLA) and made porous for osteoconductability and ease of BMP loading. The materials, with or without BMP purified from porcine bone matrix, were evaluated in cranial bone defect models in rats for biocompatibility and bone regeneration capability. The following results were obtained: The PLLA-BMP material with BMP added to the polymer showed 30% healing of cranial bone defects in rats during the 2 weeks to 3 months period of observation. The moldable PLLA agent without BMP also showed 25% bone healing capacity. Although new bone formation was incomplete in the critical size defect of rat cranium, it can be concluded that the unique moldability of those agents makes them useful for the reconstruction of various bone defects and maxillofacial deformities.

• Journal of the Mineralogical Society of Korea
• /
• v.29 no.4
• /
• pp.191-198
• /
• 2016

Pyromorphite($Pb_{4.85}(P_{1.02}O_4)_3Cl_{1.04}$) which belongs to the apatite group was compressed up to 33.4 GPa for its equation of state at ambient temperature. High pressure experiment was performed with symmetrical diamond anvil cell employing the angle dispersive X-ray diffraction method. Pressure was determined by ruby fluorescence calibration method. No phase transition were observed and bulk modulus was determined to be 80(7) GPa when $K{_0}^{\prime}=13(2)$. Employing the normalized pressure-normalized strain analysis, reliability check of the compressible behavior was conducted.

• Economic and Environmental Geology
• /
• v.29 no.1
• /
• pp.11-21
• /
• 1996

The first Mg-skarn minerals are found from magnetite ore deposits of the Janggun mine, Korea. The skarn minerals are composed of mostly chondrodite, olivine， chlorite, serpentine, phlogophite, talc, apatite, magnesite， dolomite, siderite and trace amount of clinopyroxene, amphibole, garnet, wollastonite associated with magnetite, pyrrhotite and pyrite. The skarn zone is developed in the magnetite deposits at the contact of the Mg-rich Janggun Limestone Formation and the Chunyang granite. The chondrodites are columnar and radial shapes and some of them show twins. The chemical compositions of twinning-type chondrodites have high FeO (4.63 to 5.6 wt%), MnO (0.26 to 0.46 wt%) and low MgO (55.02 to 56.18 wt%) relative to the radial-type chondrodites. Twinning in chondrodite has been formed in close relation to substitution between Mg and Fe + Mn in humite solid solution. Temperature, $-logfo_2$ and $X_{CO2}$ during the skarn stage of magnetite deposits from the Janggun mine range from 395 to $430^{\circ}C$, from 30.5 to 31.2 atm and from 0.06 to 0.09, respectively.