• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.1 no.2
• /
• pp.57-63
• /
• 2008

In this paper, we develop the Hipass antenna that is used in electronic tall-gate charging (ETC) system in Korea expressway. This antenna has circular polarized characteristics, and especially has 45 degree tilted beam properties. These properties are very effective in ETC communication between the vehicle antenna and the tall-gate antenna. To achieve these properties on a small microstrip type antenna structure, we propose a annular ring microstrip antenna with stubs. When the length and angle of stubs are changed, the direction of the circular polarized beam is generally tilted by $45^{\circ}$ in elevation angle. Especially, by using the stubs in inner area or outer area of ring antenna, it is found that the beam direction of in azimuth angle can be rotated.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.6
• /
• pp.1031-1036
• /
• 2019

This study describes the technique of the beam pattern measurement of array antenna for VHF band radar using drone and active beam pattern measuring device. There is no anechoic chamber for measuring the beam pattern of a large size antenna in the country. In this study, to test the antenna beam pattern characteristics of the developed VHF band radar, the antenna beam pattern characteristics were tested by Drone mounting an Active Beam Pattern Measuring Device. By comparing the results of the pre-simulation analysis with the measured results for the antenna, we could confirm that the beamwidth and side-lobe characteristics are satisfactory. Through the antenna beam pattern measurement technology using Drone and Active Beam Pattern Measuring Device, the beam pattern measurement technology of array antenna of low frequency band and large antenna for low band radar will be used.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.4
• /
• pp.59-65
• /
• 2022

In this paper, a digital active phased array antenna is briefly introduced and beam forming method for a dual-channel side-lobe blanking applied to blank the side-lobe of the main beam is described. Next, the antenna performance was verified from results of design and antenna near-field measurement for the antenna main beam and side-lobe blanking beam. Then, a single-channel side-lobe blanking beam forming method was proposed to reduce the number of channels than the existing system operating dual-channel side-lobe blanking beam and weight distribution for each element of the side-lobe blanking antenna was designed with the proposed method. Finally, the designed single-channel side-lobe blanking beam pattern and blanking ability were verified and compared with the dual-channel side-lobe blanking beam. In addition, by comparing/verifying the conventional dual-channel and the proposed single-channel side-lobe blanking beam patterns measured through the receiving near-field test of the digital active phased array antenna and their ability to blank side-lobe of the main beam, validity of the proposed method for forming single-channel side-lobe blanking beam was confirmed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.4
• /
• pp.92-98
• /
• 2008

A beam steering system of X-band 2-D phased array antenna for radar application is developed. The beam steering system consists of real-time command generator, beam steering unit, control PCB of array module and power supply. It plays a role of beam steering and on-line check of phased array antenna. The performance of beam steering system is verified with pulse timing of current control in phase shifters and measurement of far-field of phased array antenna. The developed beam steering system offers basic technology to develop full-scale beam steering system of multi-function radar.

• ETRI Journal
• /
• v.34 no.1
• /
• pp.1-8
• /
• 2012

This paper proposes a reconfigurable beam-steering antenna using a bended dipole and a loop. The radiation patterns of the two antennas are cancelled or compensated, and headed towards a specific direction when the dipole and loop antenna are combined at a reasonable ratio. The proposed antenna can steer the beam directions by controlling the operation of two artificial switches. The proposed antenna was manufactured on a PCB (FR-4) and a flexible PCB (polyimide). In the case of the antenna that was fabricated on a PCB, the maximum beam directions were $+50^{\circ}$, $0^{\circ}$, and $-50^{\circ}$ in the azimuth direction using the two artificial switches, and the antenna gain was 1.96 dBi to 2.48 dBi in the operation bandwidth of 2.47 GHz to 2.53 GHz. Also, the antenna was fabricated on a flexible PCB and measured under various bending conditions for wearable applications.

• International Journal of Aeronautical and Space Sciences
• /
• v.5 no.2
• /
• pp.71-76
• /
• 2004

This paper describes the antenna analysis of the multi-beam for communicationsatellite. The design core parameters of the antenna system are optimal antennadiameter, feed horn type and hom size, F/D, and the coordinate of offset horns. Thepaper deals with the method to determine design core parameters of optimal antennadiameter, feed horn type and horn size. F/D, and the coordinate of offset horns, andthe performances of design result.

• ETRI Journal
• /
• v.41 no.6
• /
• pp.715-730
• /
• 2019

We propose a switched beam-forming antenna that satisfies not only ultra-wideband characteristics but also beam-forming in the WLAN frequency band using an ultra-wideband antenna and passive parasitic elements applying a broadband optimal reactance load algorithm. We design a power and phase estimation function and an error correction function by re-analyzing and normalizing all the components of the parasitic array using control system engineering. The proposed antenna is compared with an antenna with a pin diode and reactance load value, respectively. The pin diode is located between the passive parasitic elements and ground plane. An antenna beam can be formed in eight directions according to the pin diode ON (reflector)/OFF (director) state. The antenna with a reactance load value achieves a better VSWR and gain than the antenna with a pin diode. We confirm that a beam is formed in eight directions owing to the RF switch operation, and the measured peak gain is 7 dBi at 2.45 GHz and 10 dBi at 5.8 GHz.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.465-470
• /
• 2002

A novel phased array antenna system for space-borne polarimetric SAR is proposed and completed in this paper.The antenna system assures polarimetric and multi-mode capability of SAR. It has broadband, high polarization isolation and high port to port isolation. The antenna system is composed of broadband polarimetric microstrip antenna, T/R modules and multifunction beam controller nit. The polarimetric microstrip antenna has more than 100MHz bandwidth at L-band with -30dB polarization isolation and high port to port isolation. The microstrip element and T/R module's structure and characteristics, the subarray's performances measuring results are presented in detail in this paper. A design scheme on beam controller of the phased array antenna is also proposed and completed, which is based on Digital Signal Processing (DSP) chip -TMS320F206. This beam controller unit has small size and high reliability compared with general beam controller. In addition, the multifunction beam controller unit can acquire and then send the T/R module's working states to detection system in real time.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.431-440
• /
• 2012

In this paper, new beam-forming array antenna is proposed. The proposed beam-forming array antenna has control ability for beam-direction/width by employing low loss reconfigurable power divide and three-dimensional array structure. The reconfigurable power divider is key idea in the proposed antenna, because it has reconfigurable RF power distribution ability to each antenna. And, for research and verification of the proposed antenna, 3-dimensional beam-forming array antenna is implemented, and the experimental results show that the proposed antenna has various radiation modes from 1:1 to 1:N by adjusting RF power distribution.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.3
• /
• pp.194-201
• /
• 2014

This paper is able to be solved by improving degradation in multi-path environment by adjust beam pattern angle through modifying pulse phase of each antennas by using TRM (Transmitter Receiver Module). Beam Scanning Array Antenna, which is transmitter/receiver that improves degradation in multi-path environment without any signal distortion, is designed and manufactured. Beam Scanning Array Antenna should be able to send/receive signal at the antenna's longitudinal part without distortion and should not influences other systems. Also, it should include target detecting ability by beam steering.Dispersion characteristic of Beam Scanning Antenna, which is designed, is analysed by using fidelity, and steering and radar resolution performance is verified by using $1cm{\times}1cm$ sized target. To manufacture Beam Scanning Array Antenna, control board and GUI, which is able to control Vivaldi Antenna for IR-UWB, Tri-Band Wilkinson power divider, and TRM (Transmitter Receiver Module), is designed. Throughout this research, developed Beam Scanning UWB Array Antenna system is adoptable for radar application field. and time domain analysis techniques by using network analyser made the antenna characteristics analysis for setting up antenna more accurate. In addition, it makes beam width checking without difficulties.