• KIEAE Journal
• /
• v.5 no.3
• /
• pp.3-9
• /
• 2005

Venetian blinds are used with windows to improve the uniformity ratio of illuminance and interior daylighting distribution under direct sunlit conditions. The main objective of Venetian blinds shading system is to obstruct direct sunlight and at the same time allow daylight to penetrate into the room. Venetian blinds would have greater effect on the interior daylighting condition under clear sky which has both skylight and sunlight than overcast sky which has only skylight. However, due to the lack of data, design and evaluation tools, it is difficult for architects to choose or install venetian blinds during the building design stages. The purpose of this study was to develop an analysis method for shading and daylighting effects of Venetian blinds using the RADIANCE program. The major variables related to the venetian blinds included blinds's slat angle and the ratio of slat width to window height, the radius slat of curvature and the building azimuth. In this study, a series of parametric physical mock-up model measurements and genblinds command in the RADIANCE simulations. The results of this study will provide building designers with the design data at early design stages.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.131-136
• /
• 2006

Commercial uses of GPS have been growing rapidly with applications for aircraft, ship, and land vehicle navigation as well as for surveying and time keeping. The next generation GPS and Japanese QZS (Quasi Zenith Satellite) will provide three different civil signals. Galileo will also provide several types of civil signals. The availability of the third civil frequency has obvious advantages to instantaneous carrier phase accuracy and ambiguity resolution for centimeter level measurements. This paper discusses the effects of additional new civil signals for the high accuracy positioning in urban areas based on simulation using practical raw data. As for constellation, only GPS and GPS+QZS are considered. For positioning, a short distance baseline is assumed in order to disregard atmosphere effects. In this simulation, mask angle and signal conditions were fixed and ambiguity success rates were compared between different triple frequency combination scenarios. The coefficient of reflection was set randomly from 0.05 to 0.5 and the multipath delay was also set randomly from 5-100 m. Visible satellites and signal strength were determined by raw data collected in Tokyo by car. These simulation results have confirmed that the availability of high accuracy positioning will increase in all scenarios if we use GPS+QZS with triple frequencies.

• Korean Journal of Applied Biomechanics
• /
• v.31 no.1
• /
• pp.50-58
• /
• 2021

Objective: This study aimed to determine the effect of wrist and trunk weight loading using sandbags in stroke patients in order to provide the quantitative data for enhancement of gait movement. Method: Twelve stroke patients, who have been diagnosed with hemiplegia over a year ago, were participated in this study. All subjects were asked to perform normal walking [N], wrist sandbag walking [W], wrist & trunk sandbag walking [WT], and both wrist sandbag walking [B] and both wrist & trunk sandbag walking [BT], respectively. Eight infrared cameras were used to collect the raw data. Gait parameters, arm swing, shoulder-pelvic kinematics, and lower extremity joint angle were calculated to examine the differences during walking. Results: As a result, there were no significant differences in the gait parameters, shoulder-pelvis, and lower extremities joint angles, but significant differences were found in the range of motion and the anteversion in arm swing. Conclusion: Wrist and trunk weight loading using sandbags affected the movement of the upper extremities only while it did not affect the movement of the lower extremities. It implies that it can reduce the risk of falling caused by a sudden movement change in lower extremities. In addition, the wrist and trunk weight loading using sandbags can induce changes in movement of the upper extremities independently and contribute to functional rehabilitation through resistance training.

• Economic and Environmental Geology
• /
• v.32 no.1
• /
• pp.19-31
• /
• 1999

In this study, we have estimated lineaments in the Euiseong area, Kyungbuk Province, from Landsat TM by applying the algorithm developed by Kim and Won et al. which can effectively reduce the look direction bias associated with the Sun's azimuth angle. Fratures over the study area were also mapped in the field at 57 selected sites to compare them with the results from the satellite image. The trends of lineaments estimated from the Landsat TM images are characterized as $N50^{\circ}$~70W, NS~$N10^{\circ}$W, and $N10^{\circ}$~$60^{\circ}$E trends. The spatial distribution of lineaments is also studied using a circular grid, and the results show that the area can be divided into two domains : domain A in which NS~$N20^{\circ}$E direction is dominant, and domain B in which west-north-west direction is prominent. The trends of lineaments can also be classified into seven groups. Among them, only C, D and G trends are found to be dominant based upon Donnelly's nearest neighbor analysis and correlations of lineament desities. In the color composite image produced by overlaying the lineament density map of these C-, D-, and G-trends, G-trend is shown to be developed in the whole study area while the eastern part of the area is dominated by D-trend. C-trend develops extensively over the whole are except the southeastern part. The orientation of fractures measured at 35 points in the field shows major trends of NS~$N30^{\circ}$E, $N50^{\circ}$~$80^{\circ}$W, and N80$^{\circ}$E~EW, which agree relatively well with the lineaments estimated form the satellite image. The rose diagram analysis fo field data shows that WNW-ESE trending discontinuities are developed in the whole area while discontinuities of NS~$N20^{\circ}$E are develped only in the estern part, which also coincide with the result from the satellite image. The combined results of lineaments from the satellite image and fracture orientation of field data at 22 points including 18 minor faults in Sindong Group imply that the WNW-ESE trend is so prominent that Gumchun and Gaum faults are possibly extended up to the lower Sindong Group in the study area.

• Progress in Medical Physics
• /
• v.13 no.3
• /
• pp.109-113
• /
• 2002

In recent years, the radiotherapy equipment has become much more sophisticated, and with the complication comes an increased set of quality assurance (QA) responsibilities. Today's computer controlled linear accelerator requiring QA of not only the radiation integrity, but also the mechanical accuracy of the linear accelerator. The existing QA sheets are adequate for acceptance testing and commissioning but those sheets are somewhat descriptive form for routine QA. establishing the QA sheets for a facility are more efficient if the sheets could estimate the long-term stability for the result of QA. We are going to develope new prototype of mechanical QA sheet to visualize and to verify long-term stability of mechanical QA for clinical linear accelerator. The items included in mechanical QA sheet were 1) gantry rotation, 2) collimator rotation, 3) couch rotation, 4) optical distance indicator (ODI), and 5) laser alignment. We compared new prototype sheet with conventional sheet for several hospitals in Korea for those items. The QA acceptance criteria in this study mainly followed published recommendations. The contents of test for mechanical QA are the following. Confirm that the digital and/or mechanical gantry angle readouts are correct. Verify that digital and/or mechanical readouts of collimator angle agree with the true angle, as determined with the protractor. Measure the light field using a graph paper and compare with the digital readouts. Confirm digital readout accuracy. Verify that the sagittal laser, the left and right lasers, and the ceiling laser intersect at the isocenter. In the design of new QA sheet, we emphasized the representation of the long-term stability of mechanical QA by using Excel program. By using the new prototype QA sheet, we simplified and visualized the mechanical QA process, and could estimate the long-term stability of mechanical error of linear accelerator.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.12
• /
• pp.77-86
• /
• 2012

We have carried out a series of numerical experiments to study the effect of average particle size on the mechanical properties of granite-derived weathered soils. A distinct-element method was adopted to study the changes in macro-scale mechanical properties with particle size and maximum-to-minimum particle size ratio. The numerical soil specimen with cohesion values of 0.25 MPa and internal friction angle of 29 degrees was prepared for reference. While keeping the porosity values constant, we varied particle size and size distribution to study how cohesion and internal friction angle changes. The experimental results show that the values of cohesion apparently decrease with increasing particle size. Changes in the values of internal friction angles are small, but there is a trend of increase in internal friction angle as the average particle size increases. This study demonstrates a possibility that the results of numerical experiments of this type may be used for rapid estimation of mechanical properties of granite-derived weathered soils. For example, when mechanical properties obtained through in situ tests and particle size data obtained through lab analysis are available for a site, it is expected that the mechanical properties of weathered granite soils with varying degrees of weathering (thus, varying particle size) may be estimated rapidly only with particle size data for that site.

• The Journal of Korean Physical Therapy
• /
• v.17 no.4
• /
• pp.537-557
• /
• 2005

The purpose of this study was to investigate the effect of pelvic traction and muscle energy technique(MET) for hemiplegic patients on static standing balance. The scale for static standing balance is measured by using mean balance(%), frequence(Hz), sway area($mm^2$), sway path(mm), max sway velocity(mm/s), ant/post sway angle($^{\circ}$), lateral sway angle($^{\circ}$), sway number, change of pelvic height is measured in relation to the height of ASIS and PSIS. The subjects of this study were thirty hemiplegic patients: 15men and 15 women, with an average ages of 50.80 years. The thirty subjects were divided into 3 group of 10 at random ; ten subjects had pelvic traction after bobath therapy (the pelvic traction group), ten subjects had muscle energy technique after bobath therapy (the MET group), and ten subjects had only bobath therapy (the control group). Static standing balance was measured using BPM (balance performance monitor; data print software version 5.3), pelvic height was measured using height measuring with an adjustable horizontal arm. In order to assure the statistical significant of the result, an one-way ANOVA, the paired t-test, and a person's correlation were applied at the.05 level of significance. The results of this study were as follows: 1) The change in pelvic height were statistically significant between the pelvic traction group, the MET group and the control group on pre-treatment and post-treatment(p<.05). 2) The change in affected and non-affected on weight bearing were not statistically significant between the pelvic traction group, the MET group and the control group on pre-treatment and post-treatment(p>.05). 3) The change in frequency were statistically significant between the MET group, the control group and the pelvic traction group on pre-treatment and post-treatment(p<.05). 4) The change in sway area were statistically significant between the MET group, the control group and the pelvic traction group on pre-treatment and post-treatment(p<.05). 5) The change in sway pa1h were statistically significant between the pelvic traction group, the MET group and the control group on pre-treatment and post-treatment(p<.05). 6) The change in max sway velocity were statistically significant between the pelvic traction group, the MET group and the control group on pre-treatment and post-treatment(p<.05). 7) The change in ant/post sway angle were statistically significant between the pelvic traction group, the MET group and the control group on pre-treatment and post-treatment(p<.05). 8) The change in lateral sway angle were statistically significant between the pelvic traction group, the MET group and the control group on pre-treatment and post-treatment(p<.05). 9) The change in sway number were statistically significant between the pelvic traction group, the MET group and the control group on pre-treatment and post-treatment(p<.05). In conclusion, there was a difference between the experimental group and the control group. In the future, we have to study continuously about pelvic traction and muscle energy technique in hemiplegic patients.

• Journal of the Korean Society of Costume
• /
• v.54 no.4
• /
• pp.63-74
• /
• 2004

This study shows that clothes to be just the same as the real thing can be Produced through the third dimension computer graphics, and then presents that not only the area of fashion design can be expanded in the virtual reality field by doing the simulation of the fashion show, but also the information can be made the real time public ownership and the communication can be fulfilled smoothly. In this study, analyzing the third dimension computer graphic programs to be used much at present, Alias Wavefront Company's Maya software which was the most effective in the clothes simulation and the clothes CAD SGS OptiTex 8.7 which went well substitutive for it were used of them. The conclusions of this study that got through the work manufacture are as follows： The first, if the file manufacturing in the clothes CAD by using the computer was stored, the pattern used 3D simulation was available because it could be summoned in 3D software. The second, if the data of DXF form in Maya program was summoned, they could not be applied by Maya Cloth supported in Nurbs only because they were recognized as the DXF＿layer. So the curve along the outer lines of the pattern was drawn and Maya Cloth was applied to be possible to get the natural silhouette of clothes. The third, when the clothes were manufactured by 3D, if the draping character was applied according to the textile special quality, not only the control of textile's thickness, weight, quality feeling, and silhouette was available, but also the clothes were available to graft the special textile materials. The fourth, the natural motion of model was produced by capturing the actual model's walking action In order to produce the fashion show motion and also the dynamic fashion show was available by the angle of camera, the establishment of lighting, and etc. in the final rendering. The clothes manufactured by 3D are available to change the design by changing the materials, or by adding the details, or by utilizing the special materials on clothes. Therefore, the trial and error following at the clothes manufacture can be reduced. But the elevation of the rendering speed, the price down, the strengthening of personal security, and etc. are required.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.1
• /
• pp.663-668
• /
• 2023

Recently it is very important to collect information such as enemy positions and facilities. To this end, unmanned aerial vehicles such as multicopters have been actively developed, and various mission equipment mounted on unmanned aerial vehicles have also been developed. The coordinate-oriented algorithm refers to an algorithm that calculates a gaze angle so that the mission equipment can fix the gaze at a desired coordinate or position. Flight data and GPS data were collected and simulated using Matlab for coordinate-oriented algorithms. In the simulation using only the coordinate data, the average Pan axis angle was about 0.42°, the Tilt axis was 0.003°~0.43°, and the relatively wide error was about 0.15° on average. As a result of converting this into the distance in the NE direction, the error distance in the N direction was about 2.23m on average, and the error distance in the E direction was about -1.22m on average. The simulation applying the actual flight data showed a result of about 19m@CEP. Therefore, we conducted a study on the self-error of coordinate-oriented algorithms in monitoring and information collection, which is the main task of EOTS, and confirmed that the quantitative target of 500m is satisfied with 30m@CEP, and showed that the desired coordinates can be directed.

• The Journal of Korean Medicine
• /
• v.25 no.4
• /
• pp.43-50
• /
• 2004

Objective : Obesity is associated with degenerative arthropathy giving stress on joints. It also amplifies loads of weight bearing joints by changing the gravity line of the body. Our aim is to investigate the correlation between obesity and lumbar lordosis in obese pre-menopausal Korean females. The hypothesis was tested that there is a correlation between obesity and lumbar lordosis. Methods : A cross-sectional evaluation of 44 Females (baseline age 30.77 ± 6.46) with BMI 31.53 ± 3.82 (kg/㎡) was done. Body composition was measured using bio-impedance analysis (BIA), and anthropometry was done by the same observer. A lateral whole spine X-ray was taken in standing position to measure the lumbar lordotic angle (LLA), Ferguson angle (FA) and lumbar gravity line (LGL). A Pearson correlation was used to measure the correlation between obesity and lumbar lordosis (SPSS 10.0 for windows). Results : Body mass index (BMI kg/㎡) had a negative relationship with LLA((equation omitted)=-0.469), FA((equation omitted) =-0.347) and LGL((equation omitted)=-0.389). Body fat rate had a negative relationship with LLA only(γ=-0.385). Waist circumference had a negative relationship with LLA((equation omitted)=-0.345) and LGL((equation omitted)=-0.346). WH ratio had no relationship with lumbar lordosis. Conclusion : These data show that obesity is related to mechanical structures, such as lumbar lordosis. BMI was the most useful index, which reflects a change of mechanical structure of lumbar, more than other variables in this study.