• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.304-310
• /
• 2000

The experimental study has been conducted on heat transfer characteristics of the plate heat exchangers(PHE) by several researchers. However most of all were focused on a gasket-type plate heat exchanger. Therefore further studies are need for a brazed-type. In the present study, a brazed type plate heat exchanger was tested at a chevron angle of $70^{\circ},\;55^{\circ}$ and $45^{\circ}$ with R-22 and R-410A. Condensation temperatures were $24.5^{\circ}C$, and mass flux was ranged from 35 to $60kg/m^2s$. The inlet and exit conditions are in a superheated vapor and subcooled liquid, respectively. The heat transfer coefficient increased with the chevron angle. The heat transfer coefficient of R-22 was lamer than that of R-410A for all chevron angles.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.39-47
• /
• 1988

A disk photo sensor system was constructed and installed on engine for the crank angle measurement. Statically measured TDC crank angle data were compared with those obtained from engine motoring. Two groups of cylinder pressure data were compared each other, one measured by pressure transducer mounted flush on the combustion chamber and the other obtained with the help of spark plug type adaptor. A simple analysis on the gas flow in the spark plug type pressure transducer displayed reasonably good agreement with those from engine motoring tests. In various firing tests, the IMERs obtained from the spark plug type pressure transducer turned out to be higher than those from the flush mounted one at low engine speed while those two were nearly the same at high engine speed. As the engine load decreased the relative difference in IMEP measurement between the two types tended to be enlarged.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.4
• /
• pp.138-146
• /
• 1997

The optimal drill helix angle, point angle, and cutting conditions are recommended in the study so as to maximize the drilling performance by investigating the experimental reaults concerning with the state of chip formation, roundness of machined holes, and geometry of projected burr at hole exit, which are examined under the conditions of various helix angles, drill point angles of twist drill, cutting speeds, and feeds in operional parameters. In the easiness of chip escape, the helical type of chip is producted when a helix angle is 30$^{\circ}$, drill point angle 118$^{\circ}$, 140$^{\circ}$and feed is st between 0.1 and 0.15mm/rev. Roundness of machined hole is improved when the helix angle is 37$^{\circ}$, drill point angle is 118$^{\circ}$, and feed is 0.15mm/rev. The height of projected burr at the button of machined hole increases when the drill point angle and helix angle becomes large.

• Journal of Korean Foot and Ankle Society
• /
• v.11 no.1
• /
• pp.79-85
• /
• 2007

Purpose: To evaluate the clinical efficacy of the limited posterior approach for the surgical treatment of intraarticular fracture of calcaneus. Materials and Methods: From March 2000 to February 2006, we studied retrospectively 186 patients, 203 cases who were treated with open reduction and internal fixation through limited posterior approach and were followed up for more than 1 year. The clinical results were evaluated with Creighton-Nebraska score and circle draw test after 1 year. We checked simple AP, lateral, axial and Broden's view preoperatively and 1 year after surgery, and compared $B{\ddot{o}}hler$ angle and Gissane angle. Results: By Creighton-Nebraska score, Sanders type 2 was 86.4, type 3 was 74.3, type 4 was 62.4. And by circle draw test, type 2 was 8.9 cm, type 3 was 7.2 cm, type 4 was 5.9 cm. $B{\ddot{o}}hler$ angle and Gissane angle were $7.6^{\circ}$, $102.4^{\circ}$, and it increased to $23.5^{\circ}$, $128.6^{\circ}$ after postoperative 1 year. Conclusion: Limited posterior approach for the surgical treatment of intraarticular fracture of calcaneus was considered to an effective treatment modality.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.7
• /
• pp.597-602
• /
• 2015

In this paper, we studied the steering performance of wheelset with primary suspension characteristics of railway vehicle. We carry out dynamic analysis and experimental study for the vehicle models which are different primary suspension characteristics. The steering angle of a vehicle model (Case 1) operating in domestic subway lines is insufficient compared with an objective steering angle for curved track. And the steering angle of a vehicle model (Case 2) with improved self-steering performance of wheelset is a little improved compare to previous vehicle model. But also Case 2 model is still insufficient compared with an objective steering angle and has its limit in steering performance. So to overcome this limit of steering performance of passive type railway vehicle, an active steering technology is being developed. In case of vehicle model with active steering system, the steering performance is improved remarkably compared to passive type vehicle model.

• Physical Therapy Rehabilitation Science
• /
• v.10 no.4
• /
• pp.430-437
• /
• 2021

Objective: The purpose of this study was to investigate the effect of 3-dimensional posture correction(3DPC) exercise program incorporating PNF respiratory muscle strengthening(RMS) exercise on spinal alignment and trunk expansion in patients with idiopathic scoliosis and the difference in intervention effect by type of idiopathic scoliosis. Design: Comparative study using paired t-test and analysis of variance measures. Methods: The subjects of this study were 5 men and 24 women diagnosed with idiopathic scoliosis with a Cobb angle greater than 10 degrees and less than 45 degrees. A 3DPC exercise program incorporating PNF RMS exercise was conducted twice a week for 1 hour per session for 6 weeks, and Cobb angle, Angle of trunk rotation, and trunk expansion were measured before and after the intervention. Results: After the intervention, Cobb angle and trunk rotation angle showed a statistically significant decrease, and trunk expansion showed a statistically significant increase. In the effect difference by type, there was a statistically significant difference in the angle of trunk rotation of the thoracic in 3C and Single Lumbar. Conclusions: In conclusion, it is thought that a 3DPC exercise program incorporating PNF RMS exercise can be effectively used in clinical practice to improve spinal alignment and trunk expansion in patients with idiopathic scoliosis.

• Journal of the Korean housing association
• /
• v.20 no.5
• /
• pp.9-21
• /
• 2009

This study classified visual perception types of access space at 17 five-star hotels in Jejudo and examined their cognitive characteristics and image formation structures in an effort to provide basic information important for designing the elevation and the access spaces of a hotel. The results of this study are as follows. Access space image of experimental hotels showed more negative evaluations at both city hotels and resort hotels, viewing angle (upward angle) was also positively evaluated between $10^{\circ}{\sim}12^{\circ}$ and $18^{\circ}$ and central type in arrangement type and detour access and straight access types in access circulation type were positively evaluated. When viewed from an upward angle of $10^{\circ}$ to $12^{\circ}$, the most important factors were as plasticity, decorativeness, and creativity; from $18^{\circ}$ it was such factors as harmony and peculiarity; and at $45^{\circ}$ it was factors like decorativeness and stability. In considering the various access types, the most important factors in a straight access type were peculiarity and harmony; for one-time curved access type it was by decorativeness, creativity, Peculiarity, and stability; and for detour access types it was decorativeness, stability, and peculiarity. Influential of factors affecting image formation and plasticity and harmony factors and the form had more influences on image formation.

• Journal of the Korean Society of Fashion and Beauty
• /
• v.3 no.2 s.2
• /
• pp.31-38
• /
• 2005

Make-up changes facial images. In particular, eyebrow make-up is a part of changing expression most easily and effectively. While color make-up is helpful to produce women's desired image with their favorite colors, eyebrow make-up is hidden actor to give a clear impression to others. Therefore, this study connected facial type which is an important factor deciding facial image with eyebrow, examined image of eyebrow make-up and that changed by facial types and aimed to be helpful in producing more effective facial image with eyebrow make-up considering one's facial type. Consequently, it was found that eyebrow make-up was a great factor in making better facial impression and image and complementing the weakness of facial type. h strong impression of facial type can be changed into soft shape or foolish shape in worse case depending on the types of eyebrow make-up. Eyebrow make-up shows charming image as angle of eyebrow is steep, heavy image as eyebrow is horizontal, cold image as eyebrow tail rises and simple and dull image as it lowers. Therefore, it is known that image of eyebrow make-up can be governed by several factors including angle and direction of eyebrow. Consequently, it is thought that most effective eyebrow make-up considers individual facial types, images of their eyes, noses and mouths and factors deciding angle, direction and colors of eyebrow.

• Journal of Korean Association for Spatial Structures
• /
• v.14 no.1
• /
• pp.69-76
• /
• 2014

When we excavate an underground to build basement, the ground anchors are needed to prevent collapse of neighboring ground, subsidence and movement. Ground anchor construction required shore sheet piles, wales and struts as to maintain secure excavation. Existing box-type bracket using head part of ground anchor can not be possibly adjustable to the boring angle because the brackets are manufactured with unified angle in a factory. Also, box-type brackets have imperfection and instability caused by inequable force. In this study, a new bracket system is proposed. The bracket's side plate is reinforced and the angle of boring can be controlled. To investigate the structural performance of presented brackets, FEM analysis has been performed by using ANSYS commercial program. As a result, this bracket shows sufficient stability for all angle case and the strength is increased about 24% than existing bracket.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2002.03a
• /
• pp.266-274
• /
• 2002

A typical case where the effects of prying in the base angle type anchorage system with expansion bolt. This connection consists of an angle which is attathed to an equipment cabinet and bolted to a concrete slab via an expantion bolt. A seismic analysis of the cabinet may indicate a vertical load, P, transferred to the vertical leg of the angle due to overturning of the cabinet. Due to the eccentricity, b(e), and the continuous beam action in the base member, the load resisted by the bolt will be amplified by a factor λ. Thus, in this study, experimental evaluation of the anchorage system is executed.