• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03b
• /
• pp.15-16
• /
• 2010

We used Brewster's Law to examine the mechanism of liquid crystal (LC) alignment on an organic insulation layer when subjected to ion-beam irradiation. Brewster's Law implies that the maximum rate polarized rayon a slanted insulation layers on the substrate and it illustrates the dependence of polarization and themechanical structure on the ion beam irradiation process. The pretilt angle of nematic LCs on the organic insulation surface was about $1.13^{\circ}$ for an ion beam exposure of $45^{\circ}$ for 1 minute at 1800eV. This shows the dependence of LC alignment on the polarization ratio in a slanted organic insulation layer. We also discussed the electro-optical characteristic of twisted nematic (TN) LCD using ion beam irradiation on organic overcoat layer.

• Journal of Radiation Protection and Research
• /
• v.23 no.1
• /
• pp.59-63
• /
• 1998

The light sensitivity and angular dependence of the $Mg_2SiO_4$:Tb(MSO-5) TLD which affect the accuracy of the radiation dose measurement are investigated. Light-induced thermoluminescence of MSO-S TLD under the 200 lux fluorescent and the incandescent lamp for 8 hours are corresponding to 11 and 3 mR exposure, respectively. TL intensity ratio of the incident angle of ${\pm}80^{\circ}$ to normal incidence for MSO-S and badge type MSO-L are about 0.8 and 0.15, respectively.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.3
• /
• pp.48-52
• /
• 2012

This paper describes experimental study on the orientation dependence of GM-type pulse tube refrigerator with helium and neon as working gas. A pulse tube refrigerator generates refrigeration work with gas expansion by gas displacer in the pulse tube. The pulse tube is only filled with working gas and there exists secondary flow due to large temperature difference between cold-end and warm-end. The stability of secondary flow is affected by orientation of cold-head and thus cooling performance is deteriorated by gas mixing due to secondary flow. In this study, a single stage GM-type pulse tube with orifice valve as a phase control device is fabricated and tested. The fabricated pulse tube refrigerator is tested with two different working gases of helium and neon. First, optimal valve opening and operating frequency are determined with experimental results of no-load test. And then, the variation of no-load temperature as orientation angle of cold-head is measured for two different working gases. Effect of orientation dependence of cold-head as working gas is discussed with experimental results.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.12
• /
• pp.3039-3044
• /
• 2009

We report the first electric field dependence IR spectra of three cytosine tautomers solvated in helium nanodroplets. By using an electric field dependence on the three lowest energy tautomers of cytosine and ab initio calculations, we are able to measure the vibrational transition moment angles (VTMAs), specifically for the $NH_2$ symmetric stretch (SS) mode in this study, with more precision; thus we have reassigned the previous $NH_2$ (SS) VTMA of 74$^{\circ}$ for the C1 tautomer to 85$^{\circ}$, which the latter is in excellent agreement with the ab initio value. Nonplanarity of the three lowest energy tautomers of cytosine has been investigated by measuring the VTMA of each vibrational mode for the tautomers.

• Nuclear Engineering and Technology
• /
• v.55 no.7
• /
• pp.2474-2482
• /
• 2023

The development of fast reactors with complex designs and operation status requires more accurate and effective simulation. The Monte-Carlo method can generate multi-group cross-sections in arbitrary geometry without approximation on resonances treatment and leads to good results in combination with diffusion codes. However, in previous studies, the coupling of Monte-Carlo generated multi-group cross-sections (MC-MGXS) and transport solvers has shown relatively large biases in fast reactor problems. In this paper, the main contribution to the biases is proved to be the neglect of the angle-dependence of the total cross-sections. The flux-moment homogenization technique (MHT) is proposed to take into account this dependence. In this method, the angular dependence is attributed to the transfer cross-sections, keeping an independent form for the total sections. For the MET-1000 benchmark, the multi-group transport simulation results with MC-MGXS generated with MHT are improved by 700 pcm and an additional 120 pcm with higher order scattering. The factors that cause the residual bias are discussed. The core power distribution bias is also significantly reduced when MHT is used. It proves that the MCMGXS with MHT can be applicable with transport solvers in fast reactor analysis.

• Tribology and Lubricants
• /
• v.38 no.6
• /
• pp.261-266
• /
• 2022

Notably, laser surface patterning facilitates tribological applications under lubricated sliding contacts. Consequently, a special pattern that can reduce the coefficient of friction under contact is considered necessary for improved machine efficiency. However, inappropriate pattern designs produce higher friction coefficients and cannot reduce friction. In this study, we use cast iron pins as specimens to investigate their friction and wear characteristics. Moreover, we experimentally investigate the correlation between the friction reduction effect and the design of groove crosshatch patterns fabricated with various angles and widths. We conduct a friction test using a pin-on-disc type tribometer under grease lubrication to study the friction reduction effect of the specimens, and we observe that the average coefficient of friction changes with the crosshatch angle and width. The experiment reveals that grooved crosshatch specimens with a crosshatch angle of 135°maximize friction reduction. The coefficient of friction of the groove specimens with a width of 120 ㎛ is lower than that of the specimens with a width of 200?. The friction reduction effect of the width of the groove is attributed to the density of the groove pattern. Thus, grooved crosshatch patterns can be designed to maximize friction reduction, and the friction property of a grooved crosshatch pattern is found to be related to its width and angle.

• Journal of the Korean Magnetics Society
• /
• v.4 no.4
• /
• pp.313-318
• /
• 1994

We have investigated the effects of deposition angle on magnetic and magneto-optic properties in Co/Pt multilayer thin films. which were prepared bye-beam evaporation on tilted substrates. with varying tilt angle from $0^{\circ}$ to $60^{\circ}$. The structure of the specimens was examined by x-ray diffractometer and scanning electron microscope. and the magnetic and magneto-optical properties were measured by VSM, torque magnetometer, and Kerr loop tracer. X-ray diffractometry revealed that all of the specimens had multilayer structure and growth orientation of column followed the tangent rule but the crystallograpic orientation, <111>, was slightly deviated from the substrate normal even though the deposition angle was increased up to $60^{\circ}$. A decrement of the magnetization and Kerr angle with the deposition angle was related with that of the film density due to increasing porosity. The perpendicular mag¬netic anisotropy was also decreased with increasing the deposition angle.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.3
• /
• pp.239-247
• /
• 2010

Species of fish such as striped beakperch, bluefin searobin and konoshiro gizzard shad are commercially very important due to their high demand in the Korean market. When estimating acoustically the abundance of stocks for these species, it is of crucial importance to know the target strength (TS) to the length dependence. In relation to these needs, the TS experiments were conducted on three different species in an acrylic salt water tank using two split-beam echo sounders of 70 and 120 kHz. The TS for these three species under the controlled condition was simultaneously measured with the swimming movement by a DVR system and analyzed as a function of fish length (L) and frequency (or wavelength $\lambda$). The equation of the form TS=a log (L)+b log ($\lambda$)+c was derived for their TS-length dependence. The best fit regression of TS on fork length for striped beakperch was estimated as TS=35.67 log (L, m) -15.67 log ($\lambda$, m) -46.69 ($r^2$=0.78). Furthermore, the best fit regression of TS on fork length for konoshiro gizzard shad was shown to be TS=25.85 log (L, m) -5.85 log ($\lambda$, m) -32.22 ($r^2$=0.51). The averaged TS for 12 bluefin searobins with a mean length of 24.36cm at 70 kHz was analyzed to be -41.55dB. In addition, the averaged tilt angle obtained simultaneously by a DVR system with TS measurements for 27 konoshiro gizzard shads swimming within an acrylic salt water tank was estimated at $-2.7^{\circ}$.

• Journal of the Korean Magnetics Society
• /
• v.27 no.1
• /
• pp.30-34
• /
• 2017

In this report, we calculated the angular dependence of exchange bias ($H_{ex}$) by using single domain model in exchange coupled ferromagnetic (F)/antiferromagnetic (AF) bilayers, which results with AF thickness ($t_{AF}$) were used for the analysis of measured ones in NiFe/MnIr bilayers. Angular dependence of $H_{ex}$ calculated at $t_{AF}$ > $t_c$ showed typical unidirectional behaviors, however, calculated one at $0.5t_c$ < $t_{AF}$ < $t_c$ showed peculiar angular behaviors by fixed AF spins at specified angle near ${\theta}_H=90^{\circ}$. Angular dependence of $H_{ex}$ measured in NiFe/MnIr (20 nm) bilayers showed typical unidirectional behaviors. However, measured one in NiFe/MnIr (4 nm) bilayers showed mixed behaviors including both of unidirectional and peculiar angular behaviors, which was explained by the grain size distribution of polycrystalline MnIr.

• Proceedings of the KIEE Conference
• /
• 2005.07a
• /
• pp.685-687
• /
• 2005

In this study, near the 3-phase power lines with branch lines were formulated. In rectangular coordinates, dependence of branch angle $\alpha$ on electromagnetic field components $B_x,\;B_y,\;B_z$ 및 $E_x,\;E_y,\;E_z$ was analyzed. The resultant electromagnetic fields B and E were discussed.