• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.11
• /
• pp.1930-1936
• /
• 2007

According to previously published paper the phase advance angle is adopted to the BLDC motor drive with high speed. The report proposed describes the optimum algorism that phase current is in phase with the initial flat region of back EMF. This report studies the need of more leading phase advance angle compared with in phase concept between phase current and back EMF. In case of high reactance this report proposes the more phase advance angle than in phase. The test results more rms value of phase current and output power due to more phase advance angle than in phase. It will be helped the high power operation of BLDC motor at high speed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.267-270
• /
• 1998

In this study, we investigated the generation of pretilt angle for nematic liquid crystal (NLC) in a cell with oblique non-polarized ultraviolet (UV) light irradiation on polyimide (PI) surfaces. It was found that the monodomain alignment of the NLC is obtained in a cell with an angle of incidence of 70∼85$^{\circ}$on PI surface. We consider that the monodomain alignment of NLC is attributed to anisotropic dispersion force effect due to Photo-depolymerization of polymer on PI surfaces. Also, pretilt angle of NLC is generated about 3$^{\circ}$ with an angle of incidence of 70∼75$^{\circ}$. It is considered that the pretilt angle generation in NLC is attributed to interaction between the LC molecules and the polymer surfaces.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.911-917
• /
• 1998

In this paper, we have investigated the generation of pretilt angle for nematic liquid crystal (NLC) in a cell with oblique non-polarized ultraviolet(UV) light irradiation polyimide (PI) surface. It was found that the monodomain alignment of the NLC is obtained with an angle of incidence of 70∼85。 on PI surface. It is considered that the monodomain alignment of NLC is attributed to anisotropic of NLC is about 3。 with and angle of incidence of 70∼75。. Finally, we observed that the voltage-transmittance, response time, and voltage-holding-ratio(VHR) characteristics of photo-aligned twisted nematic(TN)-LCD with and angle of incidence of 85。 on PI surface were almost same compared to rubbing -treated TN-LCD.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.6
• /
• pp.297-300
• /
• 2006

The response surface modeling of the pretilt angle control using ion-beam (IB) alignment on nitrogen doped diamond-like carbon (NDLC) thin film layer is investigated. This modeling is used to analyze the variation of the pretilt angle under various process conditions. IB exposure angle and IB exposure time are considered as input factors. The analysis of variance technique is settled to analyze the statistical significance, and effect plots are also investigated to examine the relationships between the process parameters and the response. The model can allow us to reliably predict the pretilt angle with respect to the varying process conditions.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.3
• /
• pp.145-148
• /
• 2006

In this study, the response surface modeling of the pretilt angle control using in-situ photoalignment method with oblique UV exposure .on plastic substrate is investigated. The pretilt angle is the main factor to determine the alignment of the liquid crystal display. The response surface model is used to analyze the variation of the pretilt angle on the various process conditions. Heating temperature and UV exposure time are considered as input factors. The liquid crystal (LC) pretilt angle increased with increasing heating temperature and UV exposure time. The analysis of variance is used to analyze the statistical significance and the effect plots are also investigated to examine the relationship between the process parameters and the response.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.110-116
• /
• 2011

The current study investigated the friction property of angle and width effect for micro-scale grooved crosshatch pattern on SKD11 steel surface against bearing steel using pin-on-disk type. The samples fabricated by photolithography process and then these are carry out the electrochemical etching process. We discuss the friction property due to the influence of a hatched-angle and a width of groove on contact surface. We could be explained the lubrication mechanism for a Stribeck curve. So It was found that the friction coefficient depend on an angle of the crosshatch on contact surface. It was thus verified that micro-scale crosshatch grooved pattern could affect the friction reduction. Also, it is play an important a width of groove to be improved the friction property. I was found that friction property has a relationship between a width and an angle for micro-grooved pattern.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.6
• /
• pp.16-21
• /
• 2011

In machining operation, the quality of surface finish is an important factor for many turned products. In this paper, surface quality in turning machining considering angle variation has been investigated. To reach this goal, surface quality turning experiments are carried out according to cutting conditions with angle variation. The variable cutting conditions are cutting speed, feed rate and taper angle of workpiece. The surface roughness was measured and the effects of cutting conditions were analyzed by the method of analysis of variance (ANOVA). From the experimental results and ANOVA, it is found that a better surface roughness can be obtained as decreasing feed rate, increasing cutting speed. Taper angle variation has been more influenced by feed rate and cutting speed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.3
• /
• pp.280-288
• /
• 1997

In this paper, we will show that the torque ripple in closed-loop drives of permanent magnet stepping motors is reduced as properly selected lead angle control method. We propose an instantaneous torque equation, which is the function of lead angle, to estimate the influence on torque ripple. We design a closed-loop lead angle control system based on the proposed instantaneous torque equation and measure the instantaneous torque in various excitation modes. It is shown that torque ripple is greatly reduced, as seen from the experimental results as well as from the computer simulation results. For example, torque ripple reduced from 78.25% to 46.82% in the case of 50 PPS single-phase excitation mode operation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.198-201
• /
• 1997

We investigated the generation of pretilt angle for nematic liquid crystal (NLC) in a cell with slanted non-polarized ultraviolet (UV) light irradiation on mixtured polyimide (PI) surfaces. It was found that the monodomain alignment of NLC is obtained in a cell with an angle of incidence of 75∼85 degrees on PI surface. We consider that the monodomain alignment of NLC is attributed to anisotropic dispersion force effect due to photo-depolymerization of polymer on Pl surfaces. We successfully observed that the pretilt angle of NLC is generated above 5 degree with an angle of incidence of 75∼85 degree. It is considered that the pretilt angle generation in NLC is attributed to interaction between the LC molecules and the Polymer surfaces.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.11
• /
• pp.950-953
• /
• 2000

Aligning capabilities of nematic liquid crystal(NLC) using an in-situ photo-alignment method with obliquely polarized UV exposure on a polyimide (PI) surface for homeotropic alignment were studied. The high angle for NLC can be measured by obliquely UV exposure of 30°on the PI surface for 10∼20 min. The pretilt angle of NLC generated using the in-situ photo-alignment was higher than that of a conventional photo-alignment method. Finally, we suggest that the control of pretilt angle in NLC with obliquely polarized UV exposure during imidization of the polymer for homeotropic alignment is promising method to generate high pretilt angle.