• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.611-614
• /
• 2002

Rotating stall in vaneless diffusers of centrifugal compressor occurs in the diffuser wall due to flow separation at large inlet flow angle. For this reason, the critical inlet flow angles are suggested by several researchers. Beyond this critical angle, flow separates in the diffuser, and develops into rotating stall. This paper studied this critical flow angle. Rotating stall is measured through eight fast-response pressure transducers which are equally spaced around the circumference at the inlet and exit of a vaneless diffuser. Experiments are done from 20000rpm to 60000rpm for the diffuser stall. Two-cell structure which rotates at $6{\~}l0{\%}$ of impeller speed is fully developed at $20000{\~}40000rpm$, and three-cell structure which rotates at $7{\~}9{\%}$ of impeller speed is fully developed at $50000{\~}60000rpm$. This paper shows that the critical inlet flow angle is not constant but related with tip speed of impeller. As tip speed increases, so does the critical inlet flow angle.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.281-282
• /
• 2006

In wide angle diffuser, the increasement of cross-sectional area so rapidly cause possibly separate from the diffuser wall and forming areas of backflow. The flow characteristics of wide angle diffuser with guide damper was investigated for three kind of inclined angle($\alpha=7_{\circ},\;10.5_{\circ}\;and\;14_{\circ}$)of guide damper. Judging from the results, guide damper can be used as an effective means of improvement for diffuser performance and inclined angle of $\alpha=10.5^{\circ}$ was through to be the best among three cases.

• 콘크리트학회논문집
• /
• 제12권5호
• /
• pp.81-92
• /
• 2000

A fixed angle softened truss model has been developed in order to predict both shear strength and deformation of reinforced concrete members. The model takes into account the contribution of concrete by accuming the angle of cracks in the postcracking concrete that coincides with the reinforced concrete principal compressive angle determined by the applied stresses. Therefore, this model is capable of predicting the contribution of concrete from the govering equilibrium and compatibility equations including the shear stress and strain developed along concrete diagonal crack. However, the model has a limiting range to be applicable for reinforced concrete members. This research proposes a new algorthm of fixed angle softened truss model capable of removing the limitation of applicability. The proposed algorithm adopts a new conception of constitutive laws. The average normal stresses of concrete in the x- y- directions can be calculated by transforming the principal stresses of concrete. The proposed algorthm is verified by comparing to the test results.

• 한국해양공학회지
• /
• 제19권2호
• /
• pp.60-66
• /
• 2005

This paper investigates the relationship between the fleet-angle of the hoisting rope and the swaying and pitching angles of a cargo in container cranes. It is found that for a given disturbance, when the fleet-angle is large, the sway Angle becomes smaller, but the pitching angle becomes larger. Therefore, for a quick suppression of a sway motion, it is desirable to have a large fleet-angle. The compatibility and bifurcation conditions, regarding instability, are characterized.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.264-267
• /
• 1995

In indirect vector control, if the value or the rotor tine constant used in slip calculation is different from the actual rotor time constant because of the temperature rising and flux saturation level, model flux angle and actual flux angle is different so that the transient and steady state response is degraded. In this paper, flux deviation angle is calculated by using actual torque and reference torque, and this flux deviation angle is summed to slip angle, therefore rotor flux angle is always accurate and indirect vector control is satisfied.

• 한국조명전기설비학회지:조명전기설비
• /
• 제9권3호
• /
• pp.80-87
• /
• 1995

영구자석형 스테핑 전동기의 언덕턴스를 고려하여 최대 평균 토오크식을 제시하였으며, 제시된 토오크식에 근거하여 마이크로컨트롤러에 의해 lead angle을 전동기의 속도에 따라 최적으로 제어함으로서 최대 토오크를 발생시키는 제어시스템을 설계하여 전동기의 토오크/속도 특성 실험을 하였다. 이론식에 의하면 토오크/속도 곡선에서 최적 lead angle의 도입에 따라 발생하는 토오크가 증대되며, 운전영역이 2배이상 확대되는 바와 같이, 특성실험 결과에서도 최적 lead angle의 실현에 따라 구동모드에 관계없이 발생 토오크가 증대되며, 운전영역이 2배이상 학대됨을 확인 할 수 있다.

• 한국기계가공학회지
• /
• 제2권4호
• /
• pp.82-87
• /
• 2003

Flow angle with Swirl in a horizontal circular tube and a cylindrical annuli were experimentally studied for its visualization. This present investigation deals with flow angle, flow visualization studies and vortex core by using oil smoke and a hot wire anemometer for Re = 40,000 and 50000 at X/D = 41, 59 and 71 in a horizontal circular tube. In the swirl air flow, a vortex core was formed at high swirl intensity along the test tube. The flow angle and the vortex core depended on the swirl intensity along the test tube. The results of flow angles with swirl measured by flow visualization and hot wire reasonably agree with those of Sparrow One of the primary objectives of this research was to measure the flow angle with swirl in a cylindrical annuli along the test tube for different Reynolds numbers. The Reynolds number for these measurements ranged from 60,000 to 100,000 with L/D = a to 4.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2012년도 전기공동학술대회 논문집
• /
• pp.261-262
• /
• 2012

In planar angle diffuser, the increasement of cross-sectional area so rapidly cause possibly separate from the diffuser wall and forming areas of backflow. The flow characteristics of planar angle diffuser was investigated for three kind of inclined angle. Judging from the results, wide planar diffuser can be used as an effective means of improvement for diffuser performance and inclined angle of diffuser was through to be the best among three cases.

• 한국전기전자재료학회논문지
• /
• 제14권12호
• /
• pp.1023-1026
• /
• 2001

The control of high pretilt angle for nematic liquid crystal (NLC) with negative dielectric anisotropy on the rubbed blending polyimide (PI) of homeotropic and homogeneous alignment surface was studied. High LC pretilt angle on the rubbing blending polyimide of homeotropic PI and SE-7492 surface was measured and the LC pretilt angle increased wish blending ratio and rubbing strength. However, the low LC pretilt angle on the rubbed blending polyimide of homeotropic PI and SE-150 surface was measured. The high pretilt angle of NLC can be achieved by using the blending PI surface.

• Tribology and Lubricants
• /
• 제27권1호
• /
• pp.34-39
• /
• 2011

In this study, finite element analysis of particle-surface collision using 2-dimensional elements was performed to observe the effects of abrasive size and impact angle. The result of the simulation on the change in abrasive size revealed that larger abrasive particle induced larger contact stress due to force transfer through slurry fluid as the particle moved and pushed the fluid. This observation brought an important finding that the slurry fluid could make the workpiece surface soften and then change the mechanical properties of the surface layer such as elastic modulus and yield strength. As for the impact angle, it was found that the contact stress increased with the angle of impact and jumped up at a specific angle. Such result would be attributed to the complex effects of the impact velocity and angle.