• 한국소음진동공학회논문집
• /
• 제13권1호
• /
• pp.26-32
• /
• 2003

The vibrational system of this study is consisted of a rotating cantilever pipe and the flow in the pipe. The equation of motion is derived by using Lagrange equation. The influences of the rotating angular velocity and the velocities of fluid flow in the pipe have been studied on the dynamic characteristics of a rotating cantilever pipe by numerical method. The tip-amplitude of axial vibration and maximum tip-deflection of axial direction of cantilever pipe are directly proportional to the velocity of fluid and rotating angular velocity of pipe In the steady state. respectively The bending tip-amplitude of cantilever pipe is inversely proportional to the velocity of fluid in the steady state. When the rotating angular velocity is 5 rad/s, the velocity of fluid increase with increasing the natural frequency of axial vibration at second mode and third mode, but the natural frequency axial direction of first mode is decreased. The natural frequency of lateral direction is decreased due to increase of the rotating angular velocity. It identifies that the Influence of velocity of fluid give much variation lower mode of vibration in lateral direction. And the Influence of velocity of fluid give much variation higher mode of vibration in axial direction.

• 설비공학논문집
• /
• 제15권6호
• /
• pp.480-488
• /
• 2003

The purpose of this research Is to derive the principal design parameters governing the dynamic characteristics of the high response flow control servo valve. For this purpose, a numerical modeling of the servo valve system and a parameter sensitivity analysis to a frequency response characteristics was peformed. As a result of these analysis, a basis for improvement of a dynamic characteristics of servo valve was arranged.

• Tribology and Lubricants
• /
• 제33권4호
• /
• pp.141-147
• /
• 2017

The vibration data of bearings are very useful for monitoring and determining the condition of the bearings. The defect frequencies of ball bearings have been used for monitoring there condition. However, it is not easy to verify the defect frequencies as the wear progress. Therefore there is a need for an easy method to monitor the damages of bearings in real-time and to observe the variations in vibration characteristics as the wear progress. In this study, a bearing test equipment is constructed to diagnose the damage of bearings. The friction coefficient and vibration data are measured by using a torque sensor and an acceleration sensor, and the correlation between the measured data is analyzed to diagnose the condition of the bearing. We reached the following conclusions from the results. When the ball surface, inner and outer rings of a ball bearing are damaged, the friction coefficient increases to over 0.02 with an adhesion on the surface. Moreover this damage occurs more quickly with an increase in the number of revolutions. In the vibration characteristics, the amplitude of vibration wave appears high with an increase in the friction coefficient. In the high frequency range between 1000 and 2000 Hz, a wide range of frequency components with high amplitude occurs continuously irrespective of the number of revolutions.

• 융합정보논문지
• /
• 제11권9호
• /
• pp.130-137
• /
• 2021

주파수를 갖는 외부 가진력에 의하여 강제 진동의 특성을 가진력의 진폭과 주파수에 따라 그 특성을 분석하였다. 변위, 속도 및 가속도를 얻기 위해 수치해석을 수행하여 주파수 응답을 얻었고 특히 주파수 영역에서 시스템 고유진동수와 가진 주파수의 발생 위치를 밝히고자 각각의 FRF의 분석을 하였다. 외부 가진에 의한 진동모델에서 변위, 속도 및 가속도의 거동과 주파수 응답함수에서 고유진동 주파수와 주변의 가진 모드 분포도 파워 스펙트럼과 실수부와 허수부의 FRF 에서 나타났으며 각 모드 특성도 구하였다. 진동의 응답은 가진 신호의 크기와 주파수를 주어 정현파의 가진력으로 외부 가진력을 근사화 하였고 이런 가진력에 의하여 발생하는 모드를 구별할 수 있었다. 상당 질량, 감쇠 및 강성을 변화시켜 수치 분석 후 외부 가진력에 의한 강제 진동 응답 특성을 체계적으로 분석하였다.

• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.428-439
• /
• 1998

Fluid flow and heat transfer have been numerically investigated for an oscillating flow in a tube with a regenerator. The regenerator is placed between hot and cold spaces which are heated and cooled at uniform temperature. An oscillating flow is generated by the piston motion at both ends of a tube. The time dependent, two-dimensional Navier-Stokes equations and energy equation are solved by using the finite-volume and moving grid method. The regenerator is adopted as Brinkmann-Forchheimer extended Darcy model. Numerical results are obtained for the flow and temperature fields, and described the effects of the oscillating frequency and amplitude ratio by the piston motion as well as the aspect ratio. The numerical results obtained indicate that the heat transfer between the tube wall and oscillating flow is increased as the oscillating frequency, amplitude ratio and the aspect ratio are increased.

• 한국해양공학회지
• /
• 제16권5호
• /
• pp.1-6
• /
• 2002

Extreme waves are generated in a model basin based on directional wave focusing. The targeted wave field is described by double summation method and it is applied to serpent-type wavemaker system. The extreme crest amplitude at a designed location is obtained by syncronizing the phases and focusing the directions of wave components. Two distinguished spectrums of constant wave amplitude and constant wave steepness are adapted to describe the frequency distribution of component waves. The surface profile of generated wave packets is measured by wave guage array and the effects of dominant spectral parameters governing extreme wave characteristics are investigated. It is found that frequency bandwidth, center frequency, shape of frequency spectrum and directional range play a significant role in the wave focusing. In particular, the directional effect significantly enhances the wave focusing efficiency.

• 한국소음진동공학회논문집
• /
• 제13권3호
• /
• pp.210-216
• /
• 2003

A nonlinear dynamic modeling method for cantilever beams undergoing axially oscillating motion is presented in this paper. Hybrid deformation variables are employed for the modeling method with which frequency response characteristics of axially oscillating cantilever beams are investigated. It is shown that the geometric nonlinear effects of stretching and curvature play important roles to accurately predict the frequency response characteristics. The effects of the amplitude and the damping constant on the frequency characteristics are also exhibited.

• 한국정밀공학회지
• /
• 제20권3호
• /
• pp.157-164
• /
• 2003

The pulse-echo method is one of the most widely used ultrasonic techniques for application of nondestructive evaluation. Particularly, quantitative nondestructive evaluation of defects has been considered more important to assure the reliability and the safety of structure. Frequency energy in adhesive joints is based on the ultrasonic wave analysis. The attenuation coefficient upon wave amplitude and the frequency energy that is expressed in the term of wave pressure amplitude were utilized for the primary wave experiment. By means of a control experiment, it was confirmed that the variation of the frequency energy in adhesive joints depends on transition by stress variation. In this paper, the ultrasonic characteristics were measured for single lap joint and Double Cantilever Beam specimen with different fracture modes that was subjected to stress. Consequently, the data that was obtained from the adhesive specimen was analytically compared to the fracture mechanics parameter

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.591-595
• /
• 2000

Sound absorbing characteristics of poroelastic materials is known to be greatly affected by high intensity acoustic waves. However, this effect has not been considered yet. In this study, the extended semilinear model based on Biot's theory for the porous materials and the characteristics of nonlinear waves in poroelastic sound absorbing materials were introduced. The expressions for the finite-amplitude acoustic plane waves were presented. By combining each nonlinear wave with appropriate matching conditions, we could investigate the effects of finite-amplitude acoustic waves on absorption characteristics of poroelastic materials. In the most ideal case considered in this paper, the absorption coefficient was found to become larger than that of linear incident waves. It was shown that the absorption coefficient became greater especially as frequency goes higher and as distance from the source goes larger. These phenomena may be inferred to result from 'dissipation effects due to nonlinearity'. This finding may have important implications for high intensity noise control.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1936-1941
• /
• 2003

Characteristics of the high frequency and pulsatile flow investigated experimentally to understand the flow phenomena in the hydraulic system. In the study, I axis fatigue tester which are widely used for automobile filed are selected. 4 Pressure transducer, amplifier, A/D convertor are used to analyse and to obtain the pulsatle pressure waveform with high frequencies in hydraulic system. Matlab are used. to analyse the characteristics of frequency. Variation of pump input pressure and actuator acceleration frequency, pressure wave are measured with or without accumulators. For with accumulator, frequency amplitude of pressure are very lower than those of without accumulator due to absorbing function of accumulator. As the actuator acceleration frequency increased, effect of accumulator are very important to decrease the pulsatile pressure waveform with high frequencies.