• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.2
• /
• pp.221-226
• /
• 2012

In this paper, wideband two-stage amplification stage was designed, fabricated and evaluated. The proposed amplification stage with a novel gain control method have a high gain, low noise and high linearity performance. It is consisted of common emitter amplifier as the first stage, cascode gain control amplifier as second stage and power detector which sense the received signal strength. The proposed amplification stage shows a total gain of 29 dB~37 dB, noise fiugre of 1.5 dB at operating band and high linearity performance as the IMD (third intermodulation distortion) level is below the noise level of the measurement equipment at the control voltage 2.0 V generated from power detector under the strong electric field condition.

• Journal of Biomedical Engineering Research
• /
• v.28 no.2
• /
• pp.199-204
• /
• 2007

In digital radiography, to improve the contrast of digital radiography image, the multi-scale nonlinear amplification algorithm based on unsharp masking is one of the major image enhancement algorithms. In this paper, we used the Laplacian pyramid to decompose a digital radiography(DR) image. In our simulation, the DR image was decomposed into seven layers and the coefficients of the each layer was amplified with nonlinear function. We also imported a noise containment algorithm to limit noise amplification. To enhance the contrast of image, we proposed a new adaptive non-linear gain amplification coefficients. As a result of having applied to some clinical data, a detail visibility was improved significantly without unacceptable noise boosting. Images that acquired with the proposed adaptive non-linear gain coefficients have shown superior quality to those that applied similar gain control method and expected to be accepted in the clinical applications.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.3
• /
• pp.34-42
• /
• 1993

An analytic approach to wide-band amplification using simplified equivalent MESFET modeling has enabled an ultrabroad-band flat-gain amplifier from DC to microwave. The developed lossy-match ultrabroad-band amplifier operates as a RC coupled circuit in the low-frequency range and lossless impedance matching circuit in the microwave frequency range with gain compensation circuits. The reduced gain caused by external resistors is compensated using 2-stage cascade amplification, and the gain of designed unit is 12.5.+-.1dB from the vicinity of DC to 7GAz. The experimental gain characteristics are good agreement with computer simulated results. The input and output VSWRs are measured under 2:1 over the operating frequency range, and the gain goes down over 15dBrange with various gate bias voltages.

• Korean Journal of Optics and Photonics
• /
• v.12 no.3
• /
• pp.200-204
• /
• 2001

The structural design and the measured characteristics of optical signal amplification unit for 640 Gbps (10 Gbps$\times$64 ch.) WDM transmission systems are reported. The unit is composed of two sub gain block units for the amplification of C-band (1530-1560 nm) and L-band (1570-1600 nm), respectively. Programmable microprocessors monitor the states of operation and optimize the optical output conditions. Each sub gain block unit can maintain total optical output power of +21 dBm with gain flatness of < 1 dB and noise figure of <7.2 dB for the input power in the dynamic range from-5 to +1 dBm.+1 dBm.

• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.67-73
• /
• 1994

The simulation code was developed to analyze the amplification properties of the regenerative amplifier, such as gain narrowing, nonlinear effect, and energy saturation. To reduce gain narrowing in the regenerative amplifier, the input pulse with a symmetrical shape and the same center wavelength of the active medium should be amplified in the active medium with a broad fluorescence linewidth. In this respect, Ti:Sapphire with a low nonlinear refractive index, a high saturation fluence, and a broad fluorescence linewidth is the most appropriate medium for the regenerative amplifier. The knowledge and the important parameters were acquired for the optimum design of the regenerative amplifier.

• ETRI Journal
• /
• v.24 no.2
• /
• pp.81-96
• /
• 2002

This paper describes our design of a hybrid amplifier composed of a distributed Raman amplifier and erbium-doped fiber amplifiers for C- and L-bands. We characterize the distributed Raman amplifier by numerical simulation based on the experimentally measured Raman gain coefficient of an ordinary single mode fiber transmission line. In single channel amplification, the crosstalk caused by double Rayleigh scattering was independent of signal input power and simply given as a function of the Raman gain. The double Rayleigh scattering induced power penalty was less than 0.1 dB after 1000 km if the on-off Raman gain was below 21 dB. For multiple channel amplification, using commercially available pump laser diodes and fiber components, we determined and optimized the conditions of three-wavelength Raman pumping for an amplification bandwidth of 32 nm for C-band and 34 nm for L-band. After analyzing the conventional erbium-doped fiber amplifier analysis in C-band, we estimated the performance of the hybrid amplifier for long haul optical transmission. Compared with erbium-doped fiber amplifiers, the optical signal-to-noise ratio was calculated to be higher by more than 3 dB in the optical link using the designed hybrid amplifier.

• Current Optics and Photonics
• /
• v.6 no.1
• /
• pp.32-38
• /
• 2022

Erbium-doped fiber amplifiers (EDFAs) have saturated the technological market but are still widely used in high-speed and long-distance communication systems. To overcome EDFA saturation and limitations, its erbium-doped fiber is co-doped with other materials such as zirconia and bismuth. This article demonstrates and compares the performance using three different fibers as the gain medium for zirconia-erbium-doped fibers (Zr-EDF), bismuth-erbium-doped fibers (Bi-EDF), and commercial silica-erbium-doped fibers (Si- EDF). The optical amplifier was configured with a double-pass amplification system, with a broadband mirror at the end of its configuration to allow double-pass operation in the system. The important parameters in amplifiers such as optical properties, optical amplification and noise values were also examined and discussed. All three fibers were 0.5 m long and entered with different input signals: 30 dBm for low input and 10 dBm for high input. Zr-EDF turned out to be the most relevant optical amplifier as it had the highest optical gain, longest transmission distance, highest average flatness gain with minimal jitter, and relevant noise figures suitable for the latest communication technology.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.4 no.2
• /
• pp.87-92
• /
• 2009

In this paper, we designed and fabricated the active amplification block for the integrated antenna module. The fabricated amplification module have a proper gain and low noise figure in the band of AM/FM band, T-DMB band and GPS band, and show good isolation performance for each band. Manufactured circuits satisfied the gain performance 7 dB in AM band, 11 dB in FM band, 10 dB in T-DMB, and 17 dB in GPS band. The integrated amplification block was realized by 35 mm*35 mm size, and was shown as the same sensitivity performance as compared with a conventional reference antennas.

• Journal of the Optical Society of Korea
• /
• v.7 no.3
• /
• pp.139-144
• /
• 2003

We have characterized the optical parametric chirped-pulse amplification of femtosecond Ti:sapphire laser pulses by using a BBO crystal. It is numerically verified that a high gain and a broad gain bandwidth can be obtained with a 532-nm pump laser. The dependence of the gain profile of OPA on phase matching angles, pump intensity, and crystal length is numerically investigated. Experimental results shows that the temporal fluctuation of a pump laser causes the modulation of an amplified spectrum in OPCPA.

• Korean Journal of Optics and Photonics
• /
• v.11 no.3
• /
• pp.187-192
• /
• 2000

We analyze the parametric amplification by the nonlinear characteristics in a semiconductor laser using a perturbation theory and discuss its result. The parametric gain increases with increase of the pump modulation current. It is due to shift of the resonance frequency as the pump modulation current increases. However, it decreases with increase of the bias current and damping constant. Also, it needs phase matching between the pump modulation current and signal modulation current to maximize the parametric gain. The gain decreases for a large signal modulation current due to the saturation of the amplified power. power.