• Journal of ILASS-Korea
• /
• v.23 no.1
• /
• pp.36-41
• /
• 2018

Fuel wall film effects power output and cycle deviation by changing the amount of fuel flowing into cylinder in PFI gasoline engines. Reduction of wall film can reduce fuel consumption and improve combustion stability. In this research, the effects of injection strategies including injection pressure and dual injection system is investigated for reducing wall film formation. The CONVERGE software is used for numerical analysis tool and O'Rourke film splash model was used for wall film prediction model. Compared with the reference case wall film decreased with increase of injection pressures, and the film formation reduced when the dual injection system was used.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.2
• /
• pp.169-177
• /
• 2015

In this study we investigated the regeneration methods for the lean $NO_x$ trap (LNT) catalyst in a 2.2L direct injection diesel engine. The regeneration methods were 1) in-cylinder post fuel injection and 2) external fuel injection strategy. The in-cylinder post fuel injection method uses in-cylinder injectors with the addition of the post fuel injection to supply enough reductants such as CO, $H_2$, THC. The external fuel injection method was enabled by installing a fuel injector with a wide spray angle before the LNT catalyst. Through the engine experiment, the $NO_x$ conversion efficiency, the amount of reductant exhaust gases, fuel consumption, and temperature behavior in the LNT catalyst were evaluated and compared for the two regeneration methods.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.55-60
• /
• 2004

Residual gas acts as a diluent which results in reducing the in-cylinder temperature as well as the flame speed, significantly affecting fuel economy, NOx emissions and combustion stability. Therefore it is important to determine the residual gas fraction as a function of the engine operating parameters accurately. However, the determination of the residual gas fraction is very sophisticated due to the unsteady state of induction and exhaust process. There has been little work toward the development of a generally applicable model for quantitative predictions of residual gas fraction. In this paper, a simple model for calculating the residual gas fraction in SI engines was suggested. The amount of fresh air was evaluated through AFR and fuel consumption. After this, from the intake temperature and pressure, the amount of total cylinder-charging gas was estimated. The residual gas fraction was derived by comparing the total charging and fresh air. This results coincide with measured EGR value very well.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.601-606
• /
• 1993

From the power plants in a steel plant, environment pollutants such as SOx, NOx, CO are emitted by the combustion reaction between the fuels those are by-product gases and oil. To reduce the amounts of the pollutants, it must be important that build the predictive models for the emission of the pollutants. In this paper, the model that predict the amount of future fuel consumption and the model that predict the amount of generated pollutants for the used fuel amounts is developed by using Gibb's free energy minimization method with the temperature correction techniques and neural network back propagation method. For some data set, the calculation results from this models are compared with the real emission amounts of SOx, NOx and result of the calculation by the ASPEN plus which is a commercial software. The result from this model is better than the result by ASPEN plus for this problem.

• Journal of IKEEE
• /
• v.18 no.3
• /
• pp.420-426
• /
• 2014

In this paper, we have implemented the low temperature fluidity test system with the composited fuel filter and heater, which has tested the low temperature fluidity of gasoline, an engine start time, the consumption of electricity and power to evaluate the system performance. The test condition have used the diesel fuel, the normal temperature, the diesel fuel supply pressure $3.4kgf/cm^2$ at $-20{\sim}-30^{\circ}C$, the fuel supply quantization 60 l/H, the setting current 30 A and the voltage $13V_{dc}$. In order to simulate the operation of diesel fuel filter, we will establish the composited fuel filter into test jig, and be filled with chamber tank and filter by a constant flow quantization and pressure. After these, it shall be cold for setting time. And then we have measured the consumption current and power of heater, an operating time and pressure of filter.

• Journal of Climate Change Research
• /
• v.5 no.4
• /
• pp.301-311
• /
• 2014

In this study, we estimated the amount of fuel used fishing boats of individual based on the results of survey of the activity data such as operations and activities specification of fishing boats in Korea. Based on the classification system of the domestic fishing boat, and to estimate average fuel consumption and the greenhouse gas emissions, showed emission factors per fishing boat. This was suggested to be able to apply the registration data area in the future, and estimates the emissions of greenhouse gases. Based on these results, it tries to provide the basic data that can be used when you want to create a local government measures to reduce scenario in the future.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.1
• /
• pp.45-51
• /
• 2015

In order to meet the enforced emission regulations and reduce fuel consumption, various new technologies are employed in engines. The problem of NOx emissions under a lean mixture condition should be solved, because a lean-burn direct-injection engine can realize stable lean combustion with a stratified mixture, which results in improvements in fuel economy and emissions. This study investigated the effects of intake and exhaust valve timing changes on the performance and emission characteristics of a lean-burn LPG direct-injection engine. Under a partial-load operating condition without throttling, an increase in the intake valve opening led to an increase in NOx emissions due to an increase in the amount of excess air. The fuel consumption deteriorated with an increase in the exhaust valve opening due to a decrease in the expansion work and an increase in the pumping loss.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.5
• /
• pp.609-616
• /
• 2018

The cargo handling system, which is composed of a fuel gas supply unit and cargo tank pressure control unit, is the second largest power consumer in a Liquefied Natural Gas (LNG) carrier. Because of recent enhancements in ship efficiency, the surplus boil-off gas that remains after supplying fuel gas for ship propulsion must be reliquefied or burned to regulate the cargo tank pressure. A full or partial liquefaction process can be applied to return the surplus gas to the cargo tank. The purpose of this study is to review the current partial liquefaction process for LNG carriers and develop new processes for reducing power consumption using exergy analysis. The developed partial liquefaction process was also compared with the full liquefaction process applicable to a LNG carrier with a varying boil-off gas composition and varying liquefaction amounts. An exergy analysis showed that the Joule-Thomson valve is the key component needed for improvements to the system, and that the proposed system showed an 8% enhancement relative to the current prevailing system. A comparison of the study results with a partial/full liquefaction process showed that power consumption is strongly affected by the returned liquefied amount.

• Journal of Advanced Marine Engineering and Technology
• /
• v.16 no.5
• /
• pp.97-110
• /
• 1992

Rape-seed oil has high viscosity and high rubber content like other vegetable oils. When crude rape-seed oil obtained by a general oil extraction process is used in a diesel engine, automization condition during injection is not good and a large amount of combustion product is doposited in a combustion chamber. The improvement of a diesel engine is required to use rape-seed oil as a diesel engine fuel. In this study, the physical and chemical properties and combustion characteristics of rape-seed oil were investigated. The auxiliary aid was developed to improve automization condition and the effect of the auxiliary injection aid on the performance of a diesel engine was determined. The results are as follows. 1) Oil content of rape-seed is 45%. The exraction rate is 33%. The resuls show higher values compared to those of other vegetable oils. 2) The viscosity of rape-seed oil is 50.8 cSt and nearly 14 times of diesel oil viscosity. 3) The heating value and flash point of rape-seed oil are 9720kcal/Kg and 318$^{\circ}C$, respectively. 4) In case rape-seed oil is used as fuel, brake horse power, specific fuel consumption and brake thermal efficiency are compared to those of diesel oil. The results of rape-seed oil show 3.6%, 12.7% and 3.1% higher values. 5) Particle size of injection fuel with the auxiliary injection aid on the performance of a diesel engine was determined. The results are as follows. 1) Oil content of rape-seed is 45%. The extraction rate is 33%. The results show higher values compared to those of other vegetable oils. 2) The viscosity of rape-seed oil is 50.8 cSt and nearly 14 times of diesel oil viscosity. 3) The heating value and flash point of rape-seed oil are 9720kcal/Kg and 318.deg.C, respectively. 4) In case rape-seed oil is used as fuel, brake horse power, specific fuel consumption and brake thermal efficiency are compared to theose of diesel oil. The results of rape-seed oil show 3.6%, 12.7% and 3.1% higher values. 5) Particle size of injection fuel with the auxiliary injection aids is 100.mu.m smaller than that od injection fuel without the aid. 6) Brake horse power and brake thermal efficiency with the auxiliary injection aid increase 5.07% and 6.07%, respectively. However, specific fuel consumption decreases 3.85% with the auxiliary injection aid.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.545-548
• /
• 2005

There is a close relation between the heat generation in the fuel cell stack and the fuel cell performance. In PEM fuel Gell vehicles, the stack coolant temperature is about $65^{\circ}C$, which is far lower than that for general automobile engine. Therefore, it is hard to release heat generated in the stack by using a radiator of limited size because of the reduced temperature difference between the coolant and the ambient air. In this study, indirect stack cooling system using $CO_2$ heat pump was designed and its stack cooling performance in releasing heat to the ambient was investigated. This work focuses on a series of processes that grasp the relation among the fuel cell power, the radiator capacity and the stack temperature. The purpose of this work is to find out a way to properly release sufficient amount of heat through the finite sized radiator, so that the stack power general ion can not be deteriorated due to the stack temperature increase. The optimization between the compressor power consumption and the fuel cel1 output power can be carried out to maximize the performance of fuel cell system.