• Journal of Pharmaceutical Investigation
• /
• v.33 no.1
• /
• pp.7-14
• /
• 2003

The PVP-based solid dispersion systems (SDs) containing lovastatin (LOS) and solubilizers (sodium lauryl sulfate, tween 80 and oleic acid) were prepared to enhance dissolution rate of practically water insoluble LOS using solvent evaporation method. Two different organic cosolvents either acetone/ethanol or acetonitrile/ethanol were used for the preparation of SDs. The LOS contents were highly decreased when acetone/ethanol cosolvents were used. The decrease of LOS contents was not caused by acetonitrile or acetone, based on HPLC data. The surface morphology as investigated by scanning electron microscope (SEM) and angle of repose as an index of flowability of SDs were highly dependent on the type and amount of solubilizers used. Based on differential scanning calorimetry (DSC) and X-ray powder diffraction data, the SDs made crystalline LOS into amorphous structure or partially eutectic mixtures. The simultaneous use of the solubilizers in SDs was also useful to increase dissolution rate of LOS in gastric or intestinal fluid. The SDs containing solubilizers reached 76% and 60% in gastric and intestinal fluid, respectively but the commercial tablet gave only less than 4%. These solubilizers in SDs could be also applicable for enhancing dissolution and bioavailability of poorly water-soluble drugs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.470-470
• /
• 2013

Recently, active materials such as amorphous silicon (a-Si), poly crystalline silicon (poly-Si), transition metal oxide semiconductors (TMO), and organic semiconductors have been demonstrated for flexible electronics. In order to apply flexible devices on the polymer substrates, all layers should require the characteristic of flexibility as well as the low temperature process. Especially, pentacene thin film transistors (TFTs) have been investigated for probable use in low-cost, large-area, flexible electronic applications such as radio frequency identification (RFID) tags, smart cards, display backplane driver circuits, and sensors. Since pentacene TFTs were studied, their electrical characteristics with varying single variable such as strain, humidity, and temperature have been reported by various groups, which must preferentially be performed in the flexible electronics. For example, the channel mobility of pentacene organic TFTs mainly led to change in device performance under mechanical deformation. While some electrical characteristics like carrier mobility and concentration of organic TFTs were significantly changed at the different temperature. However, there is no study concerning multivariable. Devices actually worked in many different kinds of the environment such as thermal, light, mechanical bending, humidity and various gases. For commercialization, not fewer than two variables of mechanism analysis have to be investigated. Analyzing the phenomenon of shifted characteristics under the change of multivariable may be able to be the importance with developing improved dielectric and encapsulation layer materials. In this study, we have fabricated flexible pentacene TFTs on polymer substrates and observed electrical characteristics of pentacene TFTs exposed to tensile and compressive strains at the different values of temperature like room temperature (RT), 40, 50, $60^{\circ}C$. Effects of bending and heating on the device performance of pentacene TFT will be discussed in detail.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.2 s.39
• /
• pp.15-19
• /
• 2006

The resistance switching characteristics of amorphous $SiO_2$ and poly-crystalline $TiO_2$ were investigated. Both films exhibit well defined switching characteristics with low and high resistance states. From I-V curve analyses, it was found that the low resistance states of both films obey an ohmic conduction mechanism and the high resistance states show generation of a Schottky potential barrier. Regarding the mechanism for resistance switching of the binary oxide, it is suggested that the generation and annihilation of potential barriers accounts for the changes to the high resistance state and low resistance state, respectively. The device operation characteristic parameters such as reset and set voltages of $TiO_2$ are distinctly smaller than those of $SiO_2$, indicating that the values are related to the dielectric constant.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.917-922
• /
• 2010

To assess the bioavailability of As in soils and to provide a basic information for adequate management of As contaminated fields, paddy soils and rice grains near 5 closed mines were collected and analyzed for As using sequential extraction procedure. The As contents extracted with 1M HCl against total As content in soils were ranged from 5.4 to 41.9% ($r=0.90^{**}$). However, these two contents of As in soils were not positively correlated with As concentration in rice grains. Major As fractionation of paddy soils was residual form ranging 38.1 to 84.1% except NS mine. Also, specially adsorbed fraction and fraction associated with amorphous Fe and Al oxyhydroxides, which are partially bioavailable As fractionation to the rice plant, were positively correlated with As in rice grains while fraction associated with crystalline Fe and Al oxyhydroxides and residual form were not correlated.

• Journal of the Korean Magnetics Society
• /
• v.10 no.2
• /
• pp.54-61
• /
• 2000

The structural and magnetic properties of sputtered CoNbZr alloy films were investigated. In the as-deposited $Co_{87.0}$N $b_{8.5}$Z $r_{4.5}$ film deposited at 2 mTorr and 130 W, we observed the minimum coercivity of 1.75 Oe, the maximum resistivity of 3000 $\mu$Ω.cm and permeability of 1095 at 100 MHz. As the Ar pressure or the RF input power increased, the permeability of films at 100 MHz decreased and the coercivity increased because of the development of columnar structure and the formation of unstable amorphous phase. Permeability lower than 100 and coercivity of 60 Oe were observed in film deposited at 1 mTorr or 190 W due to the formation of crystalline phase. Magnetic anisotropy field of as-deposited films could be reduced by rotating field annealing for 120 minutes at 30$0^{\circ}C$. After the annealing, the anisotropy field (Hk) decreased from 1.43 Oe to 0.3 Oe and the permeability increased from 1095 to 1345 because defects in as-deposited films were eliminated by the annealing.aling.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.680-686
• /
• 2013

Tungsten oxide films were prepared by an electrochemical deposition method for use as the anode in rechargeable lithium batteries. Continuous potentiostatic deposition of the film led to numerous cracks of the deposits while pulsed deposition significantly suppressed crack generation and film delamination. In particular, a crack-free dense tungsten oxide film with a thickness of ca. 210 nm was successfully created by pulsed deposition. The thickness of tungsten oxide was linearly proportional to deposition time. Compositional and structural analyses revealed that the as-prepared deposit was amorphous tungsten oxide and the heat treatment transformed it into crystalline triclinic tungsten oxide. Both the as-prepared and heat-treated samples reacted reversibly with lithium as the anode for rechargeable lithium batteries. Typical peaks for the conversion processes of tungsten oxides were observed in cyclic voltammograms, and the reversibility of the heat-treated sample exceeded that of the as-prepared one. Consistently, the cycling stability of the heat-treated sample proved to be much better than that of the as-prepared one in a galvanostatic charge/discharge experiment. These results demonstrate the feasibility of using electrolytic tungsten oxide films as the anode in rechargeable lithium batteries. However, further works are still needed to make a dense film with higher thickness and improved cycling stability for its practical use.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.286-286
• /
• 2011

최근 폴리머를 기판으로 하는 Flexible TFT (thin film transistor)나 3D-ULSI (three dimensional ultra large-scale integrated circuit)에서 높은 에너지 소비효율과, 빠른 반응 속도를 실현 시키기 위해 낮은 비저항(resistivity)을 가지며, 높은 홀 속도(carrier hall mobility)를 가지는 다결정 반도체 박막(poly-crystalline thin film)을 만들고자 하고 있다. 이를 실현 시키기 위해서는 높은 온도에서 장시간의 열처리가 필요하며, 이는 폴리머 기판의 문제점을 야기시킬 뿐 아니라 공정시간이 길다는 단점이 있었다. 이에 반도체 박막의 재결정화 온도를 낮춰주는 metal (Al, Ni, Co, Cu, Ag, Pd etc.,)을 이용하여 결정화 시키는 방법이 많이 연구 되어지고 있지만, 이 또한 재결정화가 이루어진 반도체 박막 안에 잔여 금속(residual metal)이 존재하게 되어 비저항을 높이고, 홀 속도를 감소시키는 단점이 있다. 이에 본 실험은 HiPIMS (High power impulse magnetron sputtering)와 PIII and D (plasma immersion ion implantation and deposition) 공정을 복합시킨 프로세스로 적은양의 금속이온주입을 통하여 재결정화 온도를 낮췄을 뿐 아니라, 잔여 하는 금속의 양도 매우 적은 다결정 반도체 박막을 만들 수 있었다. 분석 장비로는 박막의 결정화도를 측정하기 위해 GAXRD (glancing angle X-ray diffractometer)를 사용하였고, 잔여 하는 금속의 양과 화학적 결합 상태를 알아보기 위해 XPS를 통해 분석을 하였다. 마지막으로 홀 속도와 비저항을 측정하기 위해 Hall measurement와 Four-point prove를 사용하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.144-144
• /
• 2012

최근 폴리머를 기판으로 하는 고속 Flexible TFT (Thin film transistor)나 고효율의 박막 태양전지(Thin film solar cell)를 실현시키기 위해 낮은 비저항(resistivity)을 가지며, 높은 홀 속도(carrier hall mobility)와 긴 이동거리를 가지는 다결정 반도체 박막(poly-crystalline semiconductor thin film)을 만들고자 하고 있다. 지금까지 다결정 박막 반도체를 만들기 위해서는 비교적 높은 온도에서 장시간의 열처리가 필요했으며, 이는 폴리머 기판의 문제점을 야기시킬 뿐 아니라 공정시간이 길다는 단점이 있었다. 이에 반도체 박막의 재결정화 온도를 낮추어 주는 metal (Al, Ni, Co, Cu, Ag, Pd, etc.)을 이용하여 결정화시키는 방법(MIC)이 많이 연구되어지고 있지만, 이 또한 재결정화가 이루어진 반도체 박막 안에 잔류 금속(residual metal)이 존재하게 되어 비저항을 높이고, 홀 속도와 이동거리를 감소시키는 단점이 있다. 이에 본 실험은, 종래의 MIC 결정화 방법에서 이용되어진 금속 증착막을 이용하는 대신, HIPIMS (High power impulse magnetron sputtering)와 PIII&D (Plasma immersion ion implantation and deposition) 공정을 복합시킨 방법으로 적은 양의 알루미늄을 이온주입함으로써 재결정화 온도를 낮추었을 뿐 아니라, 잔류하는 금속의 양도 매우 적은 다결정 반도체 박막을 만들 수 있었다. 분석 장비로는 박막의 결정화도를 측정하기 위해 GIXRD (Glazing incident x-ray diffraction analysis)와 Raman 분광분석법을 사용하였고, 잔류하는 금속의 양과 화학적 결합 상태를 알아보기 위해 XPS (X-ray photoelectron spectroscopy)를 통한 분석을 하였다. 또한, 표면 상태와 막의 성장 상태를 확인하기 위하여 HRTEM(High resolution transmission electron microscopy)를 통하여 관찰하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.602-607
• /
• 2013

Concern for the TOS (Transparent Oxide Semiconductor) is increasing with the recent increase in interest for flexible device. Especially MgZnO has attracted a lot of attention. $Mg_xZn_{1-x}O$, which ZnO-based wideband-gap alloys is tuneable the band-gap ranges from 3.36 eV to 7.8 eV. In particular, the flexible substrate, the crystal structure of the amorphous as well as the surface morphology is not good. So research of MgZnO thin films growth on flexible substrate is essential. Therefore, in this study, we studied on the effects of the oxygen partial pressure on the structural and crystalline of $Mg_{0.1}Zn_{0.9}O$ thin films. MgZnO thin films were deposited on PES substrate by using pulsed laser deposition. We used XRD and AFM in order to observe the structural characteristics of MgZnO thin films. UV-visible spectrophotometer was used to get the band gap and transmittance. Crystallization was done at a low oxygen partial pressure. The crystallinity of MgZnO thin films with increasing temperature was improved, Grain size and RMS of the films were increased. MgZnO thin films showed high transmittance over 80% in the visible region.

• Korean Chemical Engineering Research
• /
• v.49 no.4
• /
• pp.405-410
• /
• 2011

A study on chemical vapor deposition(CVD) of $WO_3$ and the electrochromic properties of the CVD $WO_3$ films have been carried out. The crystalinity, purity, and growth rate of the films depending on substrate temperatures are investigated. The highest growth rate is $8{\mu}m/min$ at the substrate temperatures above $300^{\circ}C$ and the estimated activation energy for overall film growth is about 45.9 kJ/mol at the temperatures of $225{\sim}275^{\circ}C$, where the CVD process is controlled by a surface reaction kinetics. The films grown below $275^{\circ}C$ are amorphous, while those deposited above $300^{\circ}C$ are crystalline. The effects of thickness and deposition temperature of the $WO_3$ films on electrochromic activity are also investigated. The coloration efficiency of the films increases with increase in film thickness and decrease in deposition temperature.