• Bulletin of the Korean Chemical Society
• /
• v.25 no.5
• /
• pp.634-638
• /
• 2004

Titanium silicalite-1 (TS-1) molecular sieve was produced by microwave heating of amorphous titanium-containing solid precursors after impregnation with aqueous TPAOH solution. $SiO_2-TiO_2$ xerogel, sub-micron sized $SiO_2-TiO_2$ prepared by thermal plasma process, and Ti-containing mesoporous silica, Ti-HMS, were tested as the solid phase substrates. Highly crystalline product was obtained within 30 min. after microwave irradiation with yields over 90% using $SiO_2-TiO_2$ xerogel, which showed essentially identical physicochemical properties to TS-1 prepared by conventional hydrothermal method. Excellent catalytic activity was also obtained for 1-hexene epoxidation using $H_2O_2.\;SiO_2-TiO_2$ particles prepared by thermal plasma and Ti-HMS were found inferior as a substrate for TS-1, probably due to difficulties in wetting the surface uniformly with TPAOH.

• Journal of the Korean Magnetics Society
• /
• v.2 no.2
• /
• pp.91-98
• /
• 1992

In a $Co_{67}Fe_{4.5}Nb_{2}Si_{10}B_{15}$ amorphous alloy ribbon the effect to two-step annealing on the soft magnetic properties has been studied. By two-step annealing method which the second annealing at low temperature of $310^{\circ}C$ for 2 hours is undertaken after the primary annealing at high temperature above $480^{\circ}C$ for 20 minutes at the vacuum state, the coercive force and the squareness are not changed nearly but the initial permeability at d.c. and the effective permeability at a.c. are remark-ably increased compared with the one-step annealing. The maxima of the initial permeability and the effective permeability at 1 kHz after the two-step annealing are 290,000 and 41,000, respectively, which are 30% higher than those of the one-step annealing. The change of magnetic properties with annealing temperature is discussed in terms of the residual stress, the domain size, the cluster and the crystalline phase.

• Journal of the Korean Vacuum Society
• /
• v.5 no.3
• /
• pp.239-244
• /
• 1996

We firstly report that formation of $SiO_2$ layer on Si surface can be effectively prevented by flowing the $Si_2H_6$ gas during the heating-up procedure for amorphous Si depositions. In this way, amorphously deposited Si layer onto crystalline Si substrates can be grown epitaxially during the post-deposition heat treatments. The suppression of surface $SiO_2$ can be explained in terms of adsorption of SiHx adspecies, instead of oxygen from residual gases in the reactors, to Si surfaces after desorption of hydrogen from H-passivated Si surfaces. Employing $Si_2H_6$ flowing and soild phase epitaxial growth, high-quality epitaxial Si layer can be obtained at low temperatures below $600^{\circ}C$ without conventional high temperature cleaning procedures.

• Journal of the Korean Vacuum Society
• /
• v.10 no.3
• /
• pp.321-327
• /
• 2001

Ti-Si-N films obtained by using RF reactive sputtering of targets with various Ti/Si ratios in a $N_2(Ar+N_2)$ gas mixture have been investigated in terms of films resistivity and diffusion barrier performance. The chemical bonding state of Si in the Ti-Si-N film which contained a higher Si content was in the form of amorphous $Si_3N_4$, producing increased film resistivity with increased $N_2$flow rate. Lowering the Si content in the deposited Ti-Si-N film favored the formation of crystalline TiN even at low $N_2$flow rates, and leads to low film resistivity. In addition increasing the N content led to Ti-Si-N films having a higher density and compressive stress, suggesting that the N content in the films appear to be one of the most important factors affecting the diffusion barrier characteristics. Consequently, we proposed the optimum composition in the range of 29~49 at.% of Ti, 6~20 at.% of Si, and 45~55 at.% of N for the Ti-Si-N films having both low resistivity and excellent diffusion barrier performance.

• Korean Journal of Materials Research
• /
• v.17 no.11
• /
• pp.574-579
• /
• 2007

Amorphous $BaTi_4O_9$ ($BT_4$) film was deposited on Pt/Si substrate by RF magnetron sputter and their dielectric properties and electrical properties are investigated. A cross sectional SEM image and AFM image of the surface of the amorphous $BT_4$ film deposited at room temperature showed the film was grown well on the substrate. The amorphous $BT_4$ film had a large dielectric constant of 32, which is similar to that of the crystalline $BT_4$ film. The leakage current density of the $BT_4$ film was low and a Poole-Frenkel emission was suggested as the leakage current mechanism. A positive quadratic voltage coefficient of capacitance (VCC) was obtained for the $BT_4$ film with a thickness of <70 nm and it could be due to the free carrier relaxation. However, a negative quadratic VCC was obtained for the films with a thickness ${\geq}96nm$, possibly due to the dipolar relaxation. The 55 nm-thick $BT_4$ film had a high capacitance density of $5.1fF/{\mu}m^2$ with a low leakage current density of $11.6nA/cm^2$ at 2 V. Its quadratic and linear VCCs were $244ppm/V^2$ and -52 ppm/V, respectively, with a low temperature coefficient of capacitance of $961ppm/^{\circ}C$ at 100 kHz. These results confirmed the potential suitability of the amorphous $BT_4$ film for use as a high performance metal-insulator-metal (MIM) capacitor.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.1
• /
• pp.67-77
• /
• 1995

Abstract The principal factor affecting the increased penetration of photovoltaics into the marketplace is cost. For traditional crystalline silicon modules, half of the cost is that of the silicon wafers. As a result much effort has centered on reducing this cost by the use of thin film technologies. Substantial technical progress has been made towards improving the efficiencies of polycrystalline thin film solar cells to reduce the production costs. Progress in semiconductor deposition techniques has also been rapid. The most mature of these are based on polycrystalline silicon (p - Si), amorphous silicon (a - Si), copper indium diselenide $SuInSe_2$(CIS), and cadmium telluride (CdTe). This paper explores the recent advances in the development of polycrystalline thin film solar cells.

• The Korean Journal of Ceramics
• /
• v.5 no.2
• /
• pp.142-147
• /
• 1999

The interaction between commercial $Si_3N_4$ powder and two types of additives (nitrate and oxide additives) during the sintering of $Si_3N_4$ was investigated. The nitrates solution or oxide particles were added as a sintering additives. The surface of mixed powder was observed with FT-IR, TG, and HREM. DTA was used to characterize the reactivity of the powders. The formation of crystalline phases and phase transformation were analyzed by XRD. The adsorption of the additives on the surface of silicon nitride was confirmed in the nitrate salts. It was shown that the adsorption occurred by interaction between the amorphous $SiO_2$ layer on the $Si_3N_4$ surface and metal cations $(Al^{3++\; and \;Y^{3+})$ and anions $(NO_3\;^-\; or\; OH^-)$, resulting in a higher degree of homogeneous distribution of additives.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.21-24
• /
• 1997

Ferroeletric LiNbO$_3$ thin films hale been prepared directly on Si(100) substrates by conventional RF magnetron spurttering system for nonvolatile memory applications. As-deposited films were performed RTA(Rapid Thermal Annealing) treatment in an oxygen atmosphere at 600 $^{\circ}C$ for 60 s. The rapid thermal annealed films were changed to poly-crystalline ferroelectric nature from amorphous of as-deposition. The resistivity of the ferroelectric LiNbO$_3$ film was increased from a typical vague of 1~2$\times$10$^{8}$ $\Omega$.cm before the annealing to about 1$\times$10$^{13}$ $\Omega$.cm at 500 kV/cm and reduce the interface state density of the LiNbO$_3$/Si(100) interface to about 1$\times$10$^{11}$ cm$^2$ . eV. Ferroelectric hysteresis measurements using a Sawyer-Tower circuit yielded remanent polarization (Pr) and coercive field (Ec) values of about 1.2 $\mu$C/cm$^2$ and 120 kV/cm, respectively.

• Current Photovoltaic Research
• /
• v.1 no.2
• /
• pp.103-108
• /
• 2013

Epitaxial growth of a high-quality thin Si film is essential for the application to low-cost thin-film Si solar cells. A polycrystalline Si film was grown on a $SiO_2$ substrate at $450^{\circ}C$ by a Al-assisted crystal growth process. For the purpose, a thin Al layer was deposited on the $SiO_2$ substrate for Al-assisted crystal growth. However, the epitaxial growth of Si film resulted in a rough surface with humps. Then, we introduced a thin amorphous Si seed layer on the Al film to minimize the initial roughness of Si film. With the help of the Si seed layer, the surface of the epitaxial Si film was smooth and the crystallinity of the Si film was much improved. The grain size of the $1.5-{\mu}m$-thick Si film was as large as 1 mm. The Al content in the Si film was 3.7% and the hole concentration was estimated to be $3{\times}10^{17}/cm^3$, which was one order of magnitude higher than desirable value for Si base layer. The results suggest that Al-doped Si layer could be use as a seed layer for additional epitaxial growth of intrinsic or boron-doped Si layer because the Al-doped Si layer has large grains.

• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.443-450
• /
• 2015

This paper presents an investigation of the mechanical and microstructural properties of Class F fly ash based geopolymer containing sodium sulfate as an additive. Sodium sulfate was used as an chemical additive at the dosage levels of 0, 2, 4, and 6wt% of fly ash. Sodium hydroxide and sodium silicate solutions were used to activate fly ash. The compressive strengths of geopolymer pastes were measured at the age of 28 days. The microstructures of the geopolymer pastes were examined using XRD, MIP and SEM tests. The additions of 2wt% and 4wt% sodium sulfate produced geopolymers with high strength, while increasing the dosage of levels to 6% resulted in almost no changes in strength, comparing with the control geopolymer. The optimum increase in strength was obtained with the addition of 4wt% sodium sulfate. As the amount of sodium sulfate is increased, no additional crystalline phase was detected and no change of amorphous phase indicated despite the change in the strength development. The increase in the strength was due to the change of pore size distribution in samples. As addition of sodium sulfate altered the morphologies of reactive productions and Si/Al ratios of the reaction products, the strengths were thus affected. It was found that the strengths of geopolymer were larger for lower Si/Al ratios of reaction products formed in samples. The optimal amount of sodium sulfate in the fly ash based geopolymer helps to improve mechanical properties of the geopolymer, on the other hand, the high percentage of sodium sulfate could exist as an impurity in the geopolymer and hinder the geopolymer reaction.