• Structural Engineering and Mechanics
• /
• v.81 no.1
• /
• pp.11-28
• /
• 2022

This paper considers the combination of cyclic and axial loads to investigate the hysteretic performance of H-section 6061-T6 aluminum alloy members. The hysteretic performance of aluminum alloy members is the basis for the seismic performance of aluminum alloy structures. Despite the prevalence of aluminum alloy reticulated shells structures worldwide, research into the seismic performance of aluminum alloy structures remains inadequate. To address this deficiency, we design and conduct cyclic axial load testing of three H-section members based on a reliable testing system. The influence of slenderness ratios and bending direction on the failure form, bearing capacity, and stiffness degradation of each member are analyzed. The experiment results show that overall buckling dominates the failure mechanism of all test members before local buckling occurs. As the load increases after overall buckling, the plasticity of the member develops, finally leading to local buckling and fracture failure. The results illustrate that the plasticity development of the local buckling position is the main reason for the stiffness degradation and failure of the member. Additionally, with the increase of the slenderness ratio, the energy-dissipation capacity and stiffness of the member decrease significantly. Simultaneously, a finite element model based on the Chaboche hybrid strengthening model is established according to the experiment, and the rationality of the constitutive model and validity of the finite element simulation method are verified. The parameter analysis of twenty-four members with different sections, slenderness ratios, bending directions, and boundary conditions are also carried out. Results show that the section size and boundary condition of the member have a significant influence on stiffness degradation and energy dissipation capacity. Based on the above, the appropriate material constitutive relationship and analysis method of H-section aluminum alloy members under cyclic loading are determined, providing a reference for the seismic design of aluminum alloy structures.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.3
• /
• pp.198-203
• /
• 2016

Computer-Aided Engineering (CAE) durability analysis and experiments of an aluminum alloy brake pedal were carried out for the car lighter by die casting method. In the CAE analysis, KS standards and criteria of the Volvo Car Corporation were applied, and in the experiment, KS standards were applied. The CAE analysis results show that aluminum alloy brake pedals are stronger than the conventional steel brakes pedals because the yield strength of the aluminum alloy increased by almost 97% over that of steel. Further, the structures of the cylinder and the frame were reinforced with increasing thickness of flame and were changed to suit the die-casting process. Through a durability test based on the KS standard, the strength of a prototype of the aluminum alloy brake pedal was confirmed to be sufficient.

• Current Optics and Photonics
• /
• v.7 no.6
• /
• pp.714-720
• /
• 2023

Laser cleaning has the advantages of environmental protection, precision, and high efficiency, and has good prospects for application in removing oxide films on the surface of aluminum alloy. This paper discusses the cleaning threshold and cleaning mechanism of aluminum alloy surface oxide film. A nanosecond pulsed laser was used to remove a 5-㎛-thick oxide film from the surface of 7A04 aluminum alloy, and the target surface temperature and cleaning depth were simulated. The effects of different laser energy densities on the surface morphology of the aluminum alloy were analyzed, and the plasma motion process was recorded using a high-speed camera. The temperature measurement results of the experiment are close to the simulation results. The results show that the laser cleaning of aluminum alloy oxide film is mainly based on the vaporization mechanism and the shock wave generated by the explosion.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.720-721
• /
• 2006

The new alloy$^{1)}$ is made from rapidly solidified Al-Ni-Zr-Ce aluminum alloy powder, and has the following unique mechanical characteristics:(1) The stress-strain curve shows a yield point; (2) The alloy shows high heat resistance; (3) Although the alloy is submicron particle diameter, it shows excellent creep resistance. We observed the micro structures of this new alloy, and it is thought that is based on the following reasons:(1) The dislocation strongly adheres to the alloy's many crystal boundaries;(2) The added alloying elements have a small diffusion coefficient in aluminum;(3) The tiny intermetallic compound particles crystallizing at the grain boundary.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.754-760
• /
• 2004

Structural analysis and tests were conducted for a carbody manufactured by aluminum alloy. The results were compared, and structural safety was evaluated based on the results. Aluminum carbody in Kwangju turned out safe in terms of structural Strength.

• Journal of Powder Materials
• /
• v.30 no.4
• /
• pp.339-345
• /
• 2023

This study investigates the melting point and brazing properties of the aluminum (Al)-copper (Cu)-silicon (Si)-tin (Sn) alloy fabricated for low-temperature brazing based on the alloy design. Specifically, the Al-20Cu-10Si-Sn alloy is examined and confirmed to possess a melting point of approximately 520℃. Analysis of the melting point of the alloy based on composition reveals that the melting temperature tends to decrease with increasing Cu and Si content, along with a corresponding decrease as the Sn content rises. This study verifies that the Al-20Cu-10Si-5Sn alloy exhibits high liquidity and favorable mechanical properties for brazing through the joint gap filling test and Vickers hardness measurements. Additionally, a powder fabricated using the Al-20Cu-10Si-5Sn alloy demonstrates a melting point of around 515℃ following melting point analysis. Consequently, it is deemed highly suitable for use as a low-temperature Al brazing material.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.10a
• /
• pp.38-47
• /
• 1996

Sectional analysis program for plane strain or axisymmetric geometry of aluminum alloy sheet metals was developed. For modeling the anomalous behavior of aluminum alloy, Barlat's strain rate potential and Hill's 1990 non-quadratic yield theory arranged under the plane stress assumption were employed. 2-D rigid-viscoplastic FEM formulation based on the bending-augmented membrane theory was derived, solving simultaneously force equilibrium as well as non-penetration condition. Isotropic hardening law was also assumed for yielding behavior. To verify the validity and availability of the developed program, 2-D stretch/draw forming process for plane strain geometry and cylindrical cup deep drawing process for axisymmetric geometry were simulated.

• Steel and Composite Structures
• /
• v.46 no.3
• /
• pp.353-366
• /
• 2023

This paper presents a finite-element analysis (FEA) of aluminum alloy rectangular hollow sections (RHSs) and square hollow sections (SHSs) with circular through-openings under three-point and four-point bending. First, a finite-element model (FEM) was developed and validated against the corresponding test results available in the literature. Next, using the validated FE models, a parametric study comprising 180 FE models was conducted. The cross-section width-to-thickness ratio (b/t) ranged from 2 to 5, the hole size ratio (d/h) ranged from 0.2 to 0.8 and the quantity of holes (n) ranged from 2 to 6, respectively. Third, results obtained from laboratory test and FEA were compared with current design strengths calculated in accordance with the North American Specifications (NAS), the modified direct strength method (DSM) and the modified Continuous strength method (CSM). The comparison shows that the modified CSM are conservative by 15% on average for aluminum alloy RHSs and SHSs with circular through-openings subject to bending. Finally, a new design equation is proposed based on the modified CSM after being validated with results obtained from laboratory test and FEA. The proposed design equation can provide accurate predictions of flexural capacities for aluminum alloy RHSs and SHSs with circular through-openings.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.148-152
• /
• 2000

The aluminum alloy 6061-T6 has been successfully used in structural applications especially the pressure vessel of the Advanced Neutron Source research reactor. And aluminum alloys, including 6061-T6, have a face-centered-cubic crystals structure. Under normal circumstances face-centered-cubic crystal structures do not exhibit cleavage fractures even at very lo9w temperatures. In aluminum-based structures, plates frequently find use as connecting links. Mechanical fasteners are often utilized in instances where ease of application, familiarity with fabrication processes, and severe dynamic loading are of concern. Plates frequently find use as connecting elements in structures built from aluminum alloys. Many structural elements employ mechanical fasteners. Twenty and twenty aluminum alloy 6061-T6 plates, representing four different bolt patterns, were mechanically deformed. And variable materials such as A1 6061-T6, Al 2024-T3, Carbon/Epoxy, Glass/Epoxy Composite and Woven fiber composite, are used as patch materials. From this experiment, it has been shown that the strength of patch-repaired specimens is different with the patch materials.

• Journal of Advanced Engineering and Technology
• /
• v.11 no.4
• /
• pp.227-235
• /
• 2018

Studies on the laser cutting processing characteristics of magnesium alloys can be divided into three parts, comparing the cutting faces of magnesium alloy and aluminum alloy, observing the shape of the corner where straight lines meet, and observing the straight lines and arcs. First, there were no laser cutting conditions for magnesium alloys, so it was observed to cut magnesium alloy and aluminum alloy under the same processing conditions as aluminum alloy to shape and surface of the cut surface. Next, to observe the characteristics of the corner, we observed the shape of the corner according to the angle change of the part where the two lines meet, and finally we observed various angles to observe the characteristics of the part where the arc meets the line. Finally, laser cutting processing characteristics of magnesium alloys and aluminum alloys obtained based on the above study contents were summarized.