• Journal of Welding and Joining
• /
• v.27 no.3
• /
• pp.44-51
• /
• 2009

In this study, welding distortion analysis is performed for various design of tube shape structures which are assembled with aluminum sheet metal. Aluminum 5052 plates of 1mm thickness are used to analyze. An efficient keyhole model, as a welding heat source, is used for the prediction of full penetration weld size and shape which is required for the thermal analysis. The thermal and mechanical material properties are considered as temperature dependent functions, due to the high temperature variations during the welding. The numerical model is calculated by using a commercial software and evaluated with the experiments. The calculation results could make a comparative study in the view of distortion for the various size and shape of structure.

• Journal of the Korean Society for Railway
• /
• v.4 no.3
• /
• pp.110-115
• /
• 2001

Recently, many engineers actively participate in research and development w.r.t the weight reduction and the safety increase of vehicle body structure to meet the requirement of fuel economy and regulations. However, vehicle design concept related with weight reduction and safety increase is reduced to the design conflict problem. In the paper, the axial and bending collapse test of aluminum extruded beams are performed and the collapse characteristics are investigated. The analysis method to verify the fracture characteristics of aluminum extruded beam is presented and discussed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.240-243
• /
• 2009

Recently, many researches on the development of super-hydrophobic and anti-reflective surfaces have been concentrated on the fabrication of nano-patterned products. The nano-patterned mold is a key to replicate nano-patterned products by mass production techniques such as injection molding and UV molding. The present paper proposes fabricating nano-patterned mold with cost-effective method. The nano-pattern molded was fabricated by electroforming the anodic aluminum oxide template without E-beam lithography. The final mold with nano-patterns showed the pores with the diameter of $100{\sim}120$ nm and the height of 150 nm was fabricated.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.75-78
• /
• 2000

This study investigates the effect of surface treatment on the shear strength between aluminum panel and composite plate. The aluminum panel was surface-treated by DC Plasma and the composite Plate was surface-treated by ion beam. Lap shear test and T-peel test were performed to determine the shear strength and T-peel strength. Results showed that the shear strength of surface-treated case was 2.5 times higher than that of untreated case. The T-peel strength of treated case was more than 5 times higher than that of untreated case. SEM examination showed that the strength increase of surface-treated case was due to the more spread of epoxy to the panel.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.252-253
• /
• 2013

In this paper, we introduce the insulation of aluminum truss dry installation method for construction for the development of the Angle. Features of the development of anchor bolts have been identified as no risk of fire, and ease of construction, which has the advantage of being the adiabatic efficiency is increased. In future research, to study the angle of the field on the Application of the development for the construction.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.1
• /
• pp.47-58
• /
• 2004

Loss factors of A356, Mn-Cu alloy and aluminum matrix composites reinforced with $SiC_p$ and Ni-coated graphite particles at various contents have been investigated using clamped-free cantilever beam method. The loss factors of half-power bandwidth of the specimens were measured over a wide range of frequencies from 50 to 3300Hz. Among the specimens, Al-10%$SiC_p$-10%$C_p$ showed the highest loss factor at the mode I, while Mn-Cu alloy showed the highest loss factors at the modes II and III. Consequently, at the mode I the Al-10%$SiC_p$--10%$C_p$ showed the loss factor of 0.00093, which is 2.64 and 1.58 times higher than those of A356 and Mn-Cu alloy, respectively.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.784-792
• /
• 2018

In this letter, a standard deviation based optimization technique has been applied on High Resolution X-ray Diffraction symmetric and asymmetric scan results to accurately determine the Aluminum molar fraction and lattice relaxation of Molecular Beam Epitaxy grown compositionally graded Aluminum Gallium Nitride (AlGaN)/Aluminum Nitride/Gallium Nitride (GaN) heterostructures. Mathews-Blakeslee critical thickness model has been applied in an alternative way to determine the partially relaxed AlGaN epilayer thicknesses. The coupling coefficient determination has been presented in a different perspective involving sample tilt method by off set between the asymmetric planes of GaN and AlGaN. Sample tilt is further increased to determine mosaic tilt ranging between $0.01^{\circ}$ and $0.1^{\circ}$.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.70-71
• /
• 2014

The structural work is the main process of building construction which influence on the time, cost, safety and quality. The form work is one of the main process which has from 20 to 30 percentage of structural work. Especially the form work for beams is complex and need more manpower compared with form work for column or slab. When the existing forms such as plywood form, steel framed wooden form and aluminum form, is used for form work of beam, it would result in the cost overrun caused by needs of lots of manpower and resources. Therefore, the aim of this study is analysis of the requirement for development of SMART beam form. The result of this study shall be used for the development of SMART form work system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.1 s.256
• /
• pp.139-144
• /
• 2007

This paper presents development of carbon nanotube (CNT) tip modified by focused ion beam (FIB) and experimental results in non-contact mode of atomic force microscopy (AFM) using fabricated tip. We used an electric field which causes dielectrophoresis, to align and deposit CNTs on a conventional silicon tip. The morphology of the fabricated CNT tip was then modified into a desired shape using focused ion beam. We measured anodic aluminum oxide sample and trench structure to estimate the performance of FIB-modified tip and compared with those of conventional Si tip. We demonstrate that FIB modified tip in non contact mode had superior characteristics than conventional tip in the respects of wear, image resolution and sidewall measurement.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.680-683
• /
• 2011

This study deals with damage detection in beam structure by using modal strain energy-based technique with three different sensor types: accelerometer, lead zirconate titanate (PZT) piezoelectric sensor and electrical strain gage. First, the use of direct piezoelectric effect of PZT sensor for dynamic strain response are presented. Next, a modal strain energy-based damage detection method is outlined. For validation, forced vibration tests are carried out on lab-scale aluminum cantilever beam. The dynamic responses are measured for several damage scenarios. Based on damage localization results, the performance of three different sensor types is evaluated.