• 대한치과보철학회지
• /
• 제31권3호
• /
• pp.317-349
• /
• 1993

This study investigated the effect of filler particle size and weight% on mechanical properties of dental core porcelain. In alumina, variation in particle size and weight% and in zirconia, variation in weight%, all specimens were tested three-point bending strength, transmittance, thermal expansion coefficient, porosity and shrinkage and observed with SEM and analysed with X-ray diffractometer. In order to develop shrink-free porcelain, after firing alumina only, glass wasinfiltrated. And aluminum was added to alumina with the expanding character of aluminum oxidize into alumina, and was followed by second firing of glass infiltration procedure. Then mechanical properties were observed. The results of this study were obtained as follows. 1. The bending strength of zirconia was higher than that of alumina, and $5{\mu}m$ alumina had highest strength in variation of particle size of alumina. Except for $5{\mu}m$ alumina, increased with weight%, bending strength increased up to 80% and decreased at 90%. In case of glass infiltration, bending strength was slight higher than 80% and 90% of $5{\mu}m$ alumina. 2. Transmittance increased with increase of shrinkage, decrease of porosity, and with increase of filler size and had no direct correlation with weight%. 3. Thermal expansion coefficient of alumina group was $7.42\sim8.64\times10^{-6}/^{\circ}C$ and that of zirconia group was $9.83\sim12.11\times10^{-6}/^{\circ}C$ and the latter was higher than the former. 4. In x-ray diffraction analysis, alumina group and zirconia group increased $Al_2O_3$ peak and $t-ZrO_2$ peak with increase of weight%. The second phase(cristobalite peak) was observed in zirconia 40% group. 5. Porosity of zirconia was lower than that of alumina and $5{\mu}m$ alumina group had many pores with SEM. In case of low filler content, fracture occurred in glass and high filler content, in glass and filler. In case of aluminum addition to alumina, small oxidised aluminum was observed. 6. Zirconia group had high shrinkage than alumina group, and mixed group of alumina group had high shrinkage. In case of glass infiltration, shrinkage decreased and aluminum addition to alumina group was almost shrink-free.

• 분석과학
• /
• 제24권2호
• /
• pp.61-68
• /
• 2011

알루미나에 니켈을 코팅하는 효율을 높이기 위하여 졸-겔법을 이용하여 비결정성 알루미나를 제조한 후, 음향화학법을 이용하여 니켈을 알루미나에 코팅하여 미립자를 제조하였다. 니켈을 코팅한 알루미나 미립자는 여러 가지 소성온도($500^{\circ}C$, $1,000^{\circ}C$), 니켈용액의 농도(0.01 M~0.2 M), 초음파반응시간 (30 min, 2 h)의 조건에서 제조하였다. 제조한 미분체는 X-Ray Diffractometer (XRD), Scanning Electron Microscope (SEM), Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), Particle Size Analyzer (PSA)로 특성을 분석하였다. 니켈용액의 농도가 진해짐에 따라 그리고 초음파반응시간이 길수록 니켈의 코팅량이 증가하였다. 알루미나에 니켈을 코팅하는데 있어 $1000^{\circ}C$의 소성온도, 0.1 M의 니켈용액의 농도, 2시간의 초음파에 반응하였을 때 알루미나에 니켈이 가장 많이 코팅되었다. 그리고 평균입자의 크기는 835.9~986.7 nm였다.

• 한국재료학회지
• /
• 제23권4호
• /
• pp.250-254
• /
• 2013

In order to increase the toughness of ZTA(zirconia toughened alumina) ceramics, the present study focused on rearrangement and densification of particles according to the particle size of the parent material. When rough alumina was used for production of ZTA, densification behavior was observed in the specimen sintered at a temperature over $1550^{\circ}C$. However, it was found that the densification behavior was occurred in the specimen sintered at $1450^{\circ}C$ when fine alumina powder was used. High relative density exceeding 98% was obtained when fine alumina powder was mixed with 15 wt% of 3Y-TZP and sintered at $1600^{\circ}C$. Also, a hardness of 1820.2 Hv was obtained when a specimen containing 10 wt% of 3Y-TZP was sintered at $1600^{\circ}C$. In the case of 3Y-TZP containing rough alumina powder that had been sintered the hardness value was around 1720.3 Hv. It was predicted that an improved toughening effect in ZTA could be achieved by using finer alumina powder as the parent material.

• 한국세라믹학회지
• /
• 제35권9호
• /
• pp.923-932
• /
• 1998

Al2O3/Al composites were produced by displacement reaction method which was carried out by imm-ersing the sintered silica preform which was prepared form fused silica powder in molten aluminu. an ac-tivation energy of 94kJ/mole was calculated from Al-SiO2 reaction data in 1000-130$0^{\circ}C$ temperature range With increase of reaction temperature the alumina particle in the Al2O3/Al composites produced with pur metal Al showed grain growth and the growth of alumina particle in Al2O3/Al composite produced by using of Mg contained Al alloy was inhibited. The flexural strength of Al2O3/Al composites produced at 100$0^{\circ}C$ showed the highest value as 393 MPa. Flexural strength of the composite fabricated at 85$0^{\circ}C$ showed higher deviation than that of the composite produced at above 100$0^{\circ}C$ Low flexural strength of the composite fa-bricated at 120$0^{\circ}C$ due to the growth of pore and alumina particle size. The hardness of composites de-pended on alumina content in Al2O3/Al composite decreased with increasing of aluminium content in case the same alumina content and increased with increasing of silicon content in composite.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.263-268
• /
• 1999

Langasite, a new piezoelectric material was polished by CMP(chemical mechanical polishing). To enhance the polishing rate, alumina abrasives were added to commercial ILD1300 slurry which contains silica abrasive. The effect of added alumina 0 the silica slurry on the polishing rate and damage of langasite was investigated, Experimental results show that the polishing rate and roughness increases with increasing added alumina particle size, Crystallinity of the langasite is also lowered by alumina addition.

• 한국세라믹학회지
• /
• 제39권10호
• /
• pp.1007-1010
• /
• 2002

마이크로파 가열을 이용하여 ${\gamma}-Al_2O_3와\;Na_2SO_4$ 분말 혼합물로부터 알파 알루미나 판상체 입자를 합성하였다. 마이크로파를 이용하여 합성된 알루미나 입자의 크기와 입자분포를 마이크로파 이용 없이 동일한 혼합물로부터 합성된 분말과 비교하였다. 마이크로파를 이용하여 합성된 시료는 마이크로파 사용 없이 합성된 시료에 비하여 입자크기가 작고 입자분포가 좁음을 알 수 있었다.

• 한국세라믹학회지
• /
• 제39권8호
• /
• pp.775-782
• /
• 2002

세라믹 분말을 이용하여 슬러리와 분산제의 농도에 따른 조대입자 함량평가에 대한 연구를 수행하였다. 시판용의 알루미나 분말을 조대입자 분리용 시료로 사용하였으며, 분산제로는 sodium hexametaphosphate와 sodium polyacrylate를 사용하였다. 알루미나 농도의 증가 및 분산제 농도의 감소에 따라 조대입자의 함량이 증가하였다. 슬러리 내의 시료농도가 1.0wt%이고, 시료에 대해 1.0wt%의 분산제를 첨가하였을 때 조대입자의 함량이 가장 작게 측정됨을 알 수 있었다. 고분자 분산제인 sodium polyacrylate를 사용하여 sodium hexametaphosphate보다 조대입자의 함량이 크게 측정되었다. 실험횟수가 증가함에 따라, 체의 질량이 일정한 비율로 감소하는 경향을 나타냈다. 조대입자의 함량을 알고 있는 임의의 슬러리를 제조하여 실험을 실시한 결과, 본 연구에서 사용한 습식 체분리 방법은 조대입자 함량평가에 적합한 것으로 사료된다.

• The Journal of Advanced Prosthodontics
• /
• 제9권2호
• /
• pp.130-137
• /
• 2017

PURPOSE. The purpose of this study was to evaluate the effect of nano-structured alumina surface coating on shear bond strength between Y-TZP ceramic and various dual-cured resin cements. MATERIALS AND METHODS. A total of 90 disk-shaped zirconia specimens (HASS CO., Gangneung, Korea) were divided into three groups by surface treatment method: (1) airborne particle abrasion, (2) tribochemicalsilica coating, and (3) nano-structured alumina coating. Each group was categorized into three subgroups of ten specimens and bonded with three different types of dual-cured resin cements. After thermocycling, shear bond strength was measured and failure modes were observed through FE-SEM. Two-way ANOVA and the Tukey's HSD test were performed to determine the effects of surface treatment method and type of cement on bond strength (P<.05). To confirm the correlation of surface treatment and failure mode, the Chi-square test was used. RESULTS. Groups treated with the nano-structured alumina coating showed significantly higher shear bond strength compared to other groups treated with airborne particle abrasion or tribochemical silica coating. Clearfil SA Luting showed a significantly higher shear bond strength compared to RelyX ARC and RelyX Unicem. The cohesive failure mode was observed to be dominant in the groups treated with nano-structured alumina coating, while the adhesive failure mode was prevalent in the groups treated with either airborne particle abrasion or tribochemical silica coating. CONCLUSION. Nano-structured alumina coating is an effective zirconia surface treatment method for enhancing the bond strength between Y-TZP ceramic and various dual-cured resin cements.

• Transactions on Electrical and Electronic Materials
• /
• 제16권6호
• /
• pp.338-341
• /
• 2015

Epoxy/micro-sized alumina composite was prepared, and the effects of alumina content on the dielectric properties were investigated in order to develop an insulation material for gas-insulated switchgears (GIS). Nano-sized alumina (average particle size: 30 nm) was also incorporated into the epoxy/micro-sized alumina composite. Dielectric tests were carried out in ASTM D 150, and capacitance (Cp) and dielectric loss (tanδ) were measured. The dielectric constant increased with increasing alumina content in the epoxy/micro-alumina system and the epoxy/micro-alumina/nano-alumina system. As 1,3-diglycidyl glyceryl ether (DGE) content increased, the dielectric constant decreased and dielectric loss increased. This ocurred as a result of the weak electric field enhancement due to homogeneous dispersion of micro- and nano-sized alumina particles in an epoxy composite.

• 한국전기전자재료학회논문지
• /
• 제29권10호
• /
• pp.613-619
• /
• 2016

The aim of this study is to improve of dielectric properties using epoxy/nano alumina composites with adding glycerol diglycidyl ether (GDE:1,2 g). This paper deals with the effects of dielectric properties(${\epsilon}^{\prime}_r$ and $tan{\delta}$) for epoxy/nano alumina contents (1,3 phr) and GDE addition (1,2 g)composites. 5 kinds specimen were prepared with containing epoxy resins, epoxy nano alumina composites. Average particle size of nano used were 30 nm. The nano alumina used were gamma phase particles of spherical shape. The suppression of epoxy chain motion by addition of nano alumina+GDE decreased dielectric loss and relative permittivity magnitude.