• Journal of the Korean Ceramic Society
• /
• v.29 no.8
• /
• pp.667-673
• /
• 1992

The alumina-zirconia composite powders of core particle ZrO2 coated with Al2O3 were prepared by the hydrolysis-deposition of the mixed aluminum salt solution of Al2(SO4)3-Al(NO3)3-Urea. The effects of hydrolysis reaction and coating parameters on characteristics of coated powders and composites were also investigated. The degree of coating could be estimated from the ratio of tetra-/mono-ZrO2 present at the room temperature after heat-treating coated powders at 120$0^{\circ}C$ and the result of TEM observations. When the content of ZrO2 in the dispersed coating system, the coating time, and the volume ratio of water/solution were 50 mg/g, 180 min, and 5, respectively the coating efficiency was maximum (the ratio of tetra-/mono-ZrO2 was 87/13). The relative densities of coated Al2O3-ZrO2 composites sintered at 1$650^{\circ}C$ for 4 hrs were about 91~98% and the maximum ratio of tetra-/mono-ZrO2 in Al2O3-20wt% ZrO2 composites was 62/38.

• Journal of Radiation Industry
• /
• v.4 no.4
• /
• pp.359-364
• /
• 2010

PVDF-HFP (binder)/silylated alumina (inorganic particle)-coated PE (polyethylene) separators were with various compositions of binder and inorganic particle were prepared by a dip-coating process with humidity control (R.H. 25% and 50%) using electron beam irradiation. The morphology of the coated PVDF-$HFP/Al_2O_3$ layer with various compositions of PVDF-HFP and $Al_2O_3$, and humidity condition was found to be an important factor in determining ionic conductivity of the prepared separators. The PVDF-$HFP/Al_2O_3$ (5/5)-coated PE separator prepared at R.H. 50% followed by electron beam irradiation at 200 kGy was applied for lithium-ion polymer battery and the cell test results showed improved high-rate discharge performance and better cyclic stability compared to the cells with the bare PE and the PVDF-HFP-coated PE separators.

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3235-3241
• /
• 2022

The Korea Atomic Energy Research Institute (KAERI) is planning the construction of the KIJANG Research Reactor (KJRR) for stable supply of ⁹⁹Mo. The Fission ⁹⁹Mo Production Process (FMPP) of KJRR produces solid waste such as spent uranium cake and alumina cake, and liquid waste in the form of intermediate level liquid waste (ILLW) and low level liquid waste (LLLW). This study thus established the operating range and optimum operating conditions for the cementation of ILLW from FMPP. It also evaluated whether cement waste form samples produced under optimum operational conditions satisfy the waste acceptance criteria (WAC) of a disposal facility in Korea (Korea radioactive waste agency, KORAD). Considering economic feasibility and safety, optimum operational conditions were achieved at a w/c ratio of 0.55, and the corresponding salt content was 5.71 wt%. The cement waste form samples prepared under optimum operational conditions were found to satisfy KORAD's WAC when tested for structural stability and leachability. The results indicate that the proposed cementation conditions for the disposal of ILLW from FMMP can be effectively applied to KJRR's disposal facility.

• Korean Journal of Materials Research
• /
• v.28 no.6
• /
• pp.361-364
• /
• 2018

Binary Ti-Al alloys below 51.0 mass%Al content exhibit a breakaway, transferring from parabolic to linear rate law. The second $Al_2O_3$ layer might have some protectiveness before breakaway. Ti-63.1 mass%Al oxidized at 1173 K under parabolic law. Breakaway oxidation is observed in every alloy, except for Ti-63.1 mass%Al. After breakaway, oxidation rates of the binary TiAl alloys below 34.5 mass%Al obey almost linear kinetics. The corrosion rate of Ti-63.1 mass%Al appears to be almost parabolic. As content greater than 63.0 mass% is found to be necessary to form a protective alumina film. Addition of Mo improves the oxidation resistance dramatically. No breakaway is observed at 1123 K, and breakaway is delayed by Mo addition at 1173 K. At 1123 K, no breakaway, but a parabolic increase in mass gain, are observed in the Mo-added TiAl alloys. The binary Ti-34.5 mass%Al exhibits a transfer from parabolic to linear kinetics. At 1173 K, the binary alloys show vary fast linear oxidation and even the Mo-added alloys exhibit breakaway oxidation. The 2.0 mass%Mo-added TiAl exhibits a slope between linear and parabolic. At values of 4.0 and 6.0 mass% added TiAl alloys, slightly larger rates are observed than those for the parabolic rate law, even after breakaway. On those alloys, the second $Al_2O_3$ layer appears to be persistently continuous. Oxidation resistance is considerably degraded by the addition of Mn. Mn appears to have the effect of breaking the continuity of the second $Al_2O_3$ layer.

• Korean Journal of Pharmacognosy
• /
• v.22 no.3
• /
• pp.171-182
• /
• 1991

Several experiments were carried for the purpose of establishing the basis for the quality evaluation of deer horn. Deer horn originated from China, New Zealand, Soviet and Alaska were used as objectives and some constituents involved in deer horn were assayed and compared with one another. Five kinds of trace elements including Ca and Fe were determined by atomic absorbance spectroscopy. The more the region came down from the top of the deer horn, the more the ratio of Ca to Fe content (Ca/Fe) was increased. The same increasing tendancy was observed in the case of ash content. Gangliosides were isolated from deer horn by alumina column chromatography and identified by TLC using gangliosides Type II obtained from bovine brain as the standard material. The TLC chromatograms were scanned by dual wavelength TLC scanner, then those TLC profiles were compared. Deer horn from China and New Zealand were analogous but those from Soviet and Alaska were each distinguished in their TLC profiles.

• Journal of the Korean Ceramic Society
• /
• v.35 no.1
• /
• pp.5-10
• /
• 1998

Mullitization in a multicomponent oxide system(alumina-kaolin-quartz-feldspar-talc) was studied as a function of sintering temperature from 1200 to 1500$^{\circ}C$ based upon a quantitative X-ray diffraction analysis. In the present study mullite grew as wiskers and its formation reaction showed characteristic there stages as follows In the first stage(1255-1295$^{\circ}C$) an appreciable mullitization(nucleation) occurred while corun-dum dissolution into glass (increasing glass content ) limited the rate of the reaction. At 1295-1335$^{\circ}C$ (second state) the reaction was significantly enhanced with a considerable glass consumption and with no appreciable change in corundum content. Finally (above 1335$^{\circ}C$) the reaction rate was attenuated re-markably with an apparent decrease in glass consumption rate. The impingement of mullite whiskers by oth-er whiskers and crystals was speculated to cause mullite growth in thickness direction with a slow growth rate resulting in the diminished reaction rate in the final stage.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.3
• /
• pp.211-218
• /
• 2022

Coal ash is being considered as a source of silica and alumina for cement clinker. The purpose of this study was to investigate the effect on cement clinker sintering by confirming the high-temperature microstructural change according to the firing temperature in the cement clinker sintering process of coal ash. In the coal ash used as a raw material for cement clinker, the shape change of the particle surface was confirmed from the sintering tem perature of 950 ℃. The shape of the coal ash disappeared from the sintering temperature higher than 1250 ℃. It was confirmed that the Al and Fe components of the coal ash were converted to the cement interstitial phase at a temperature higher than 1350 ℃. In addition, the clinker using a large amount of coal ash as a raw material showed a low content of Lime and a high content of Belite in the sintering tem perature range of 1150~1200 ℃. From this, it was confirmed that the formation of calcium silicate mineral proceeds more easily at the initial sintering temperature by the application of coal ash.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.4
• /
• pp.180-188
• /
• 2013

The glass of E-glass fiber composition was fabricated by using refused coal ore which is obtained as by-product from Dogye coal mine in Samcheok. We used silica-alumina refused coal ore which has low carbon content relatively, and the amount of refused coal ore has been changed from 0 to 35 % in batch composition. E-glass was fabricated by the melting of mixed batch materials at $1550^{\circ}C$ for 2 hrs with different refused coal ore composition of 0~35 %. We obtained a transparent and clear glass with high visible light transmittance value of 81~84%, thermal expansion coefficient of $5.39{\sim}5.61{\times}10^{-6}/^{\circ}C$ and softening point of $851{\sim}860^{\circ}C$. The glass fiber samples were also obtained through fiberizing equipment at $1150^{\circ}C$, and tested chemical resistance and tensile strength to evaluate the mechanical property as a reinforced glass fiber of composite material. As the result, we identified the properties of E-glass fiber by using refused coal ore are plenty good enough compare to that of normal E-glass without refused coal ore, and confirmed the possibility of refused coal ore as for the raw material of E-glass fiber.

• Journal of Conservation Science
• /
• v.33 no.3
• /
• pp.215-223
• /
• 2017

The purpose of this study is to reveal the characteristics, correlations, and colorant materials of those using the chemical compositions of 30 glasses excavated from the Sarari hall of the Mireuksaji stone pagoda, and to determine the correlations between them and other glass excavated from the Wanggungri site. The results of the chemical analysis of the 11 glass beads show that they are a soda glass group with high contents of $SiO_2$ and $Na_2O$; these can be further subdivided into soda-alumina groups ($Na_2O-Al_2O_3-CaO-Si_2O$). The characteristics of the stabilizer are classified as being of the high alumina glass group (LCHA), except for two glasses. It was concluded that colorant materials affected the coloring for glass beads by various components including Ti, Mn, Fe, Cu and Pb. In addition, we examined six lead glasses which are glass plate and unknown fragments that are of a common lead glass system ($PbO-SiO_2$) with respect to the average contents of PbO (70wt.%) and $SiO_2$ (30wt.%). As a result of comparing these relics with those of the glass beads excavated by Wanggungri, there is a similarity in that they belong to the soda glass group. However, the contents of $Na_2O$ are relatively higher than that of the glass beads in the Mireuksaji pagoda, and most of relics include glasses with a low content of $K_2O$ and CaO. In addition, the PbO and $SiO_2$ contents are slightly different in the lead glass. It seems that the glass relics made at two different sites may have used different raw materials or techniques.

• Economic and Environmental Geology
• /
• v.45 no.5
• /
• pp.535-549
• /
• 2012

Main aspect of this study are to clarify mineral compositions on granites in Youngkwang-Naju area. These granites are is divided into four rock facies based on the geologic ages, mineralogical composition and chemical constituents, and texture : hornblende-biotite granodiorite, biotite granite, porphyritic granite and two mica granite. These granites constitude an igneous complex formed by a series of differentiation from cogenetic magma. In compressive stress field between the Ogcheon folded belt and the Youngnam massif, the foliated and undeformed granites had formed owing to heterogeneous distribution of stress. The geochemical data of study area indicate magma of these rocks would had been generated by melting in lower and middle crust. The major minerals of granitic rocks in study area are plagioclase, biotite, muscovite and hornblende. Plagioclase range in composition from oligoclase ($An_{19.3-27.7}$) to andesine ($An_{28.4-31}$), and shows normal zoning patterns, This uniformed composition indicated slow crystallization, and it is obvious that the growth of these crystal occurred before final consolidation of the magma. The Mg content of biotite are increases with increasing of $f_{O2}$ and grade of differentiation, changing from phlogopite to siderophyllite. Its $Al^{iv}$/$Al^{total}$ ratios are propertional to bulk rock alumina content. Muscovite is primary in origin with high content of $TiO_2$, and Its composition correspond to celadonitic muscovite. Hornblende indicated calc amphibole group ($(Ca+Na)_{M4}{\geq}1.43$, $Na_{M4}<0.67$). and consolidation pressure of granitic body by geobarometer of Hammerstrume and Zen show 11.3~17.2 Km.