• 열처리공학회지
• /
• 제11권2호
• /
• pp.121-130
• /
• 1998

The effects of alloying elements(Mo, Cu, Ni) and austempering temperature conditions on the microstructural morphologies and mechanical properties in austempered ductile cast iron has been investigated. The austempering at $350^{\circ}C$ for 2hrs after austenitizing at $900^{\circ}C$ for 2hrs in all specimens with various alloying elements was optimum because the good combination of tensile and yield strength, hardness and impact value was obtained. The microstructures of these ADIs treated by a forementioned austempering condition are nearly a mixture type of needle and feathery bainite. Among those alloys, Mo-Cu alloyed DCI had the best optimum mechanical properties of hardness and toughness for automobile parts by austempering treatment for 2hrs at $900^{\circ}C$ followed by $350^{\circ}C$ for 2hrs.

• 한국수소및신에너지학회논문집
• /
• 제10권1호
• /
• pp.1-7
• /
• 1999

In order to study on the effect of fabrication methods on the changes of hydrogenation properties of FeTi alloy, FeTi samples were prepared using three different methods, i.e., arc melting, mechanical alloying and combination of the two methods. The FeTi prepared by mechanical alloying represented amorphous structure. The hydrogen storage capacity of arc melted FeTi alloy is larger than any other samples. However, FeTi electrode fabricated by mechanical alloying after arc melting showed largest discharge capacity among them.

• 한국분말재료학회지
• /
• 제4권2호
• /
• pp.122-132
• /
• 1997

Nanostructured(NS) W-Cu composite powders of about 20~30 nm grain size were synthesized by mechanical alloying. The properties of NS W-Cu powder and its sintering behavior were investigated. It was shown from X-ray diffraction and TEM analysis that the supersaturated solid solution of Cu in W was not formed by the mechanical alloying of mixed elemental powders, but the mixture of W and Cu particles with nanosize grains, i.e., the nanocomposite powder was attained. Nanocomposite W-20wt%Cu and W-30wt%Cu powders milled for 100 h were sintered to the relative density more than 96% and 98%, respectively, by sintering at 110$0^{\circ}C$ for 1 h in $H_2$. Such a high sinterability was attributed to the high homogeneous mixing and ultra-fine structure of W and Cu phases as well as activated sintering effect by impurity metal introduced during milling.

• 한국분말재료학회지
• /
• 제2권2호
• /
• pp.165-170
• /
• 1995

Alloying behavior of nanocrystalline Al-Ti-(Si) composite powders via mechanical alloying (MA) has been investigated, and the effect of Si on the microstructural changes during MA was discussed. The microstructures of both MA powders and extruded compacts were examined. In Al-Ti system, the solid solutionized nanocrystalline powders could be obtained by MA. On the contrary, fine Si particles were embedded as an elemental state in the matrix of Al-Ti-Si system because of the brittleness and the negligible solid solubility of Si in Al. After hot extrusion, $Al3Ti$ phase was finely precipitated in Al-10fSTi alloy, and Si particles were dissolved to form $(Al, Si)_3Ti$ phase in Al-10%Ti-2%Si alloy.

• 한국분말재료학회지
• /
• 제5권3호
• /
• pp.220-226
• /
• 1998

W-12.8wt%Cu-7.2%Pb powders were milled at room temperature and $-100^{\circ}C$ to investigate the mechanical alloying behavior of immiscible W-Cu-Pb system and the effect of milling temperature on the extent of alloying and microstructural refinement. W-Cu-Pb powder reached steady state after further extended milling due to Pb addition, compared to the W-Cu system. The cryomilling at $-100^{\circ}C$ caused the more refinement of powder particle size, and enhanced the solubility of Cu or Pb in W, compared with milling at room temperature. In W-12.8wt%Cu-7.2%Pb powder cryomilled at $-100^{\circ}C$, the monotectic temperature of Cu-Pb as well as the melting temperature of Cu was decreased by refinement of Cu crystalline size, and the most amorphization was occurred after milling for 150 h.

• 한국분말재료학회지
• /
• 제18권3호
• /
• pp.238-243
• /
• 2011

Al/AlN composites were synthesized by mechanical alloying using process control agents(PCAs). Three different PCAs which contain N element, were examined to see the effectiveness of ball-milling and the nitridation during sintering. Among examined PCAs, $C_8H_6N_4O_5$ was the most effective to facilitate ball-milling and to form nitrides during a subsequent sintering. By a proper control of ball-milling and sintering, we could obtained surface-hardened Al-based composites.

• 한국분말재료학회지
• /
• 제3권1호
• /
• pp.42-48
• /
• 1996

To investigate the phase transformation behaviors of mechanically alloyed Nb-25 at%Al powders, the mixed Nb-25 at%Al powders were mechanically alloyed in SPEX 8000 Mixer/Mill. Mechanical alloying(MA) time was varied between 0.5 hour and 72 hours. The phase formation behaviors of these mechanically alloyed powders were examined using X-ray diffraction(XRD), scanning electron microscopy(SEM), transmission electron microscopy(TEM), and differential thermal analysis(DTA). Appreciable amorphization started from 6 hours of MA. The powders mechanically alloyed for 10 hours were in almost amorphous phase. DTA results showed that the powders mechanically alloyed for 12 hours had a strong exothermic peak about$600^{\circ}C$, whereas the powders mechanically alloyed for 6 hours had two exothermic peaks. The first peak was found to be due to the stress relief effect and the second one due to the formation of$Nb_{3}Al,Nb_{2}Al and Nb_{2}C$phases by crystallization.

• 한국세라믹학회지
• /
• 제29권8호
• /
• pp.630-638
• /
• 1992

Ta2O5 alloying into 3 mol% Y2O3-stabilized tetragonal ZrO2 polycrystals (3Y-TZP) increased the degradation during aging at 265℃ and the fracture toughness; both are determined by the amount of transformed m-ZrO2. It was proposed that the mechanism underlying the t→m transformation when aged at low temperatures is attributed to the reorientation of (Zzr'V ). complexes parallel to [111] lattice direction, which is accompanied by a relaxation of TZP lattice during annealing at low temperature. A small strain which results from the reorientation gives rise to a localized mechanical instability, thus lowering the nucleation barrier so that the t→m phase transformation (degradation) proceeds. The amount of transformed m-ZrO2 during aging becomes greater as the chemical free energy change related to the transformation, ΔGo, increases with increasing the Ta2O5 alloying content.

• 한국주조공학회지
• /
• 제9권6호
• /
• pp.483-489
• /
• 1989

In the stable eutectoid transformation of austenite in ductile cast iron, ferrite forms around the graphite spheroid. As carbon diffuses through the ferrite ring, the graphite spheroid must eularge and the ferrite ring must deform plastically to accomodate this growth. A model has been proposed to clarify this mechanism. The alloying effects of molybdenum, nickel and copper were studied in a series of heats cast into a range of casting section sizes. Regression analysis was used to illustrate the effects of alloying and cooling rate on the microstructure of ductile cast iron.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.64-71
• /
• 2003

In order to evaluate the effect of alloying elements (Nb and Sn) on the wear resistance of advanced Zr fuel claddings, sliding wear tests have been performed in room temperature air and water and these results were compared with those of commercial alloys such as Zircaloy-4, A and B alloys. As a result, the advanced Zr fuel claddings have a similar wear resistance compared with the commercial alloys. The wear resistance of the advanced Zr fuel claddings is closely releted to the content of Nb and Sn even though the effects of transition elements are involved in deforming wear properties. In the tested specimens with similar Sn content, wear volume became down to a minimum at $0.4\;wt\;\%$ Nb, then rapidly increased at 1.0 wt Nb. This behavior results in the variation of grain size with alloying contents. But Sn did not have a significant effect on the wear volume of advanced Zr fuel claddings below $1.1\;wt\%$. The relationship between alloying elements and wear behaviour was evaluated and discussed using material compatibility factor.