• Journal of the Korea Institute of Building Construction
• /
• v.17 no.1
• /
• pp.47-54
• /
• 2017

Cement industry is typical carbon-emission industry. If the industrial by-products(granulated blast-furnace slag (GGBFS), fly ash, etc.) are used a large amount, it might be able to reduce cement consumption and mitigate carbon emissions. In this case, however, decrease of early strength is relatively large. Therefore, there is a limitation in increase of the amount of substitute. Considering these circumstances, it would be a good solution to reduce carbon emissions in cement industry to improve the performances of mixed cement through proper alkali-activation in Portland blended cement using GGBFS or fly ash. Therefore, this study prepared concrete in ready-mixed concrete manufacturing facilities with an addition of a binder which used 2.0% modified alkali sulfate activator after mixing Portland cement, GGBFS and fly ash in the ratio of 4:4:2 and assessed its basic properties. The results found the followings: The use of modified alkali-sulfate activator slightly reduced slump and shortened setting time. As a result, bleeding capacity decreased while early strength improved. In addition, there is no big difference in carbonation resistance. It appears that there should be continued experiments and analyses on the related long-term aged specimens.

• Environmental Engineering Research
• /
• v.25 no.4
• /
• pp.536-544
• /
• 2020

To address organic dye wastewater, economic and effective adsorbents are required. Here, magnetic biochar from alkali-activated rice straw (AMBC) was successfully synthesized using one-step magnetization and carbonization method. The alkaline activation caused the large specific surface area, high pore volume and abundant oxygen-containing groups of the AMBC, and the magnetization gave the AMBC a certain degree of electropositivity and fast equilibrium characteristics. These characteristics collectively contributed to a relative high adsorption capacity of 53.66 mg g^-1 for this adsorbent towards rhodamine B (RhB). In brief, RhB can spontaneously adsorb onto the heterogeneous surface of the AMBC and reach the equilibrium in 60 min. Although the initial pH, ionic strength and other substances of the solution affected the adsorption performance of the AMBC, it could be easily regenerated and reused with considerable adsorption content. Based on the results, H-bonds, π-π stacking and electrostatic interactions were speculated as the primary mechanisms for RhB adsorption onto the AMBC, which was also demonstrated by the FTIR analysis. With the advantageous features of low cost, easy separation, considerable adsorption capacity and favorable stability and reusability, the AMBC would be a potential adsorbent for removing organic dyes from wastewater.

• Korea-Australia Rheology Journal
• /
• v.12 no.2
• /
• pp.93-100
• /
• 2000

The interactions between methylated $\beta$-cyclodextrin (CD) and hydrophobically modified alkali-soluble associative polymers (HASE) were examined by a rheological technique. The effect of "capping" of hydrophobes by methylated $\beta$-cyclodextrin on the viscosity and modulus was evaluated. Model HASE polymers with $C_1$to $C_{20}$ alkyl hydrophobic groups ethoxylated with~10 moles of ethylene-oxide (EO 10) and at concentrations up to 3 wt% were examined. With the addition of methylated $\beta$-CD, the steady shear viscosity profiles shift from a Newtonian profile to one that display a shear-thinning characteristic. Significant "capping" of the hydrophobes occurs for HASE polymers with $C_{l2}$, $C_{16}$ and $C_{20}$ hydrophobes as reflected by the large reduction in the viscosity. However, the steady shear viscosity remains constant when the concentration of $\beta$-CD exceeds 1 wt%, suggesting that $\beta$-CD is not able to fully encapsulate the hydrophobes of the HASE polymer. The temperature variation plots indicate that the activation energy of the HASE-EO10-$C_{20}$ system and $\beta$-CD is dependent on the magnitude of the applied shear stress. These results further reinforce the hypothesis that $\beta$-CD is not able to completely remove all the hydrophobic associations.phobic associations.

• Korean Journal of Materials Research
• /
• v.26 no.10
• /
• pp.521-527
• /
• 2016

Geopolymers have many advantages over Portland cement, including energy efficiency, reduced greenhouse gas emissions, high strength at early age and improved thermal resistance. Alkali activated geopolymers made from waste materials such as fly ash or blast furnace slag are particularly advantageous because of their environmental sustainability and low cost. However, their durability and functionality remain subjects for further study. Geopolymer materials can be used in various applications such as fire and heat resistant fiber composites, sealants, concretes, ceramics, etc., depending on the chemical composition of the source materials and the activators. In this study, we investigated the thermal properties and microstructure of fly ash and blast furnace slag based geopolymers in order to develop eco-friendly construction materials with excellent energy efficiency, sound insulation properties and good heat resistance. With different curing times, specimens of various compositions were investigated in terms of compressive strength, X-ray diffraction, thermal property and microstructure. In addition, we investigated changes in X-ray diffraction and microstructure for geopolymers exposed to $1,000^{\circ}C$ heat.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.33-39
• /
• 1999

This study was conducted to confirm the effect of bypass dust on the hydration and mechanical properties of the cement pastes and mortar obtained from ordinary Portland cement (OPC), OPC-slag and OPC-fly ash system. The rate of heat evolution is accelerated with the content of By-pass Dust(BD). total heat evolution increased because alkali-chlorides activated the hydration of blended cement. Compressive strength and bound water content show maximum value at 5wt% By-pass Dust(BD) on each curing time in ordinary Portland cement and slag blended cement. Ca(OH)2 content of Ordinary Portland Cement increased as the content of BD and curing time. In blended cement, the formation of Ca(OH)2 is active at early hydration stage. By pozzolanic reaction, the content of Ca(OH)2 is decreased as curing time goes by. According to the BD content stable chlorides complex of Friedel's salt (C3A·CaCl2·10H2O) is created. Due to the hydration activation effect of chlorides and alkali we observed Type II C-S-H, which developed into densest microstructure.

• Advances in materials Research
• /
• v.4 no.3
• /
• pp.133-144
• /
• 2015

The aim of this investigation is to prepare geopolymer resin by alkali activation of ceramic waste (AACW) with different sodium hydroxide (NaOH) and liquid sodium silicate (LSS) concentrations. In order to prepare geopolymer cement, AACW was replaced by 10 and 30 % by weight (wt.,) of concrete waste (CoW) as well as 10 and 30 wt., % ground granulated blast-furnace slag (GGBFS). The results showed that, the compressive strength of AACW increases with the increase of activator content up to 15:15 wt., % NaOH: LSS. All AACW hardened specimens activated by 3:3 (MC6), 6:6 (MC12), 12:12 (MC24) and 15:15 wt., % (MC30) NaOH: LSS destroyed when cured in water for 24h. The MC18 mix showed higher resistivity to water curing. The results also showed that, the replacement of AACW containing 9:9 wt., % NaOH: LSS (MC18) by 10 (MCCo10) and 30 (MCCo30) wt., % CoWdecreased the compressive strength at all ages of curing. In contrast, the MCCo10 mix showed the lower chemically combined water content compared to MC18 mix. The MCCo30 mix showed the higher chemically combined water content compared to MC18 and MCCo10 mixes. The compressive strength and chemically combined water of all AACWmixes containing GGBFS (MCS10 and MCS30) were higher than those of AACWwith no GGBFS (MC18). As the amount of GGBFS content increases the chemically combined water increases. The x-ray diffraction (XRD) proved that as the amount of CoWcontent increases, the degree of crystallinity increases. Conversely, the replacement of AACW by GGBFS leads to increase the amorphiticity character. The infrared spectroscopy (FTIR) confirms the higher reactivity of GGBFS compared to CoW as a result of successive hydration products formation, enhancing the compaction of microstructure as observed in scanning electron microscopy (SEM).

• Korean Journal of Food Science and Technology
• /
• v.28 no.3
• /
• pp.538-544
• /
• 1996

A highly viscous biopolymer from alkali-tolerant Bacillus sp. was purified and its rheological properties were studied. 1% (w/v) solution of purified biopolymer showed pseudoplastic fluid behavior with the yield stress similar to those of xanthan and guar gum, and its consistency index was exponentially dependent on concentration and temperature. The concentration dependency of consistency index exhibited two rectilinear plots with different slopes at 1% concentration and pseudoplastic property increased with the increase of biopolymer concentration. The biopolymer solution exhibited a low temperature dependency and the activation energy of flow was 1.16 kacl/g mol. The apparent viscosity was very dependent on the change of pH and the addition of salt. However, no organic solvent effects were observed effects of viscosity synergism with the addition of viscosifier were not observed.

• Journal of the Korea Concrete Institute
• /
• v.18 no.4 s.94
• /
• pp.449-458
• /
• 2006

The discharge of fly ash that is produced by coal-fired electric power plants is rapidly increasing in Korea. The utilization of fly ash in the raw materials would contribute to the elimination of an environmental problem and to the development of new high-performance materials. So it is needed to study the binder obtained by chemically activation of pozzolanic materials by means of a substitute for the cement. Fly ash consists of a glass phase. As it is produced from high temperature, it is a chemically stable material. Fly ash mostly consists of $SiO_2\;and\;Al_2O_3$, and it assumes the form of an oxide in the inside of fly ash. Because this reaction has not broken out by itself, it is need to supply it with additional $OH^-$ through alkali activators. Alkali activators were used for supplying it with additional $OH^-$. This paper concentrated on the strength development according to the kind of chemical activators, the curing temperature, the heat curing time. Also, according to scanning electron microscopy and X-Ray diffraction, the main reaction product in the alkali activated fly ash mortar is Zeolite of $Na_6-(AlO_2)_6-(SiO_2)_{10}-12H_2O$ type.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.6
• /
• pp.415-421
• /
• 2013

To increase specific surface property of activated carbon fiber(ACF), chemical activation(CA) using alkali metals and surface treatment(ST) using oxidant was widely used. The CA and ST process developed micro-pore on the surface of ACF by chemical reaction of the alkali metals and oxidative of oxidant, respectively. To improve the efficiency of CA process for developing micro-pores on the surface of ACF, the ST process was adopted as an pre-treatment method. After treatment of ST process, ACF properties was investigated depending on the ST pre-treatment process. FT-IR, TG and elemental analysis of the ACF are carried out, and an adsorption property of ACF was also evaluated using toluene(which in typical volatile organic matter). Once the single CA process is used, the surface area and adsorption capacity of ACF were increased from 1,483 to 1,988 $m^2/g$ and from 0.22 to 0.27 $g_{-Tol.}/g_{-ACF}$, respectively. On the other hands, once the ST and CA processes are used successively, the surface area and adsorption capacity of ACF are greatly increase(where the surface area is 2,743 $m^2/g$ and the adsorption capacity is 0.37 $g_{-Tol.}/g_{-ACF}$). It indicates that the combined process of ST and CA can improve the surface process properties of ACF.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.34-35
• /
• 2015

The purpose of this study is to investigate the compressive strength property of concrete with Ground granulated blast furnace slag(GBFS) using wash water from recycled aggregate. When GBFS is reacted with water, it doesn't happen to hydraulic reaction but GBFS becomes latent hydraulic property in alkaline environment. For this reason, if it is possible to use wash water from recycled coarse aggregate as mixture water, GBFS have the advantage of early strength due to effect of activation. We investigated the compressive strength properties of GBFS concrete using wash water from recycled aggregate. According to the experimentation result, ICP-OES showed wash water from recycled coarse aggregate has a high alkali value of pH of 12. Also, compressive strength in early age using wash water can be improved as an activation.