• Electrical & Electronic Materials
• /
• v.10 no.1
• /
• pp.15-19
• /
• 1997

The characteristics of the response time and the viewing angle on twisted nematic (TN) liquid crystal display (LCD) and amorphous (a)-TN-LCD without rubbing were investigated. To measure the tansmission-voltage, response time, and viewing angle characteristics, we prepared three kinds of LC cells and then studied the surface liquid crystal alignment effect. It was found that the response time on A-TN-LCD was fast compared to the TN-I-CD, and the weak anchoring strength was attributed to the fast response time on a-TN-LCD. Also, we obtained the wide viewing angle characteristics on a-TN-LCD. The liquid crystal alignment of LCD device for electro-optical characteristics is discussed in the present paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.487-488
• /
• 2005

We have investigated the Electro-Optical Characteristics for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using plastic substrates. It was found that monodomain alignment of NLC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. EO characteristics of the TN-LCD with a rubbed PI surface based on polymer are almost the same as that of the TN-LCD with a rubbed PI surface based on glass. However, the transmittances of the TN-LCD with a rubbed PI surface based on polymer is less than that with a rubbed PI surface based on glass.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.583-585
• /
• 2004

In this paper, we synthesized a new photo-crosslinkable polyitaconimide containing cinnamoyl moiety by radical polymerization. Also, the NLC alignment capabilities on these photopolymer surfaces were studied. Good LC alignment with W exposure on the polyitaconimide surfaces can be obtained. A homogenous alignment using UV exposure on the polyitaconimide with 1-carbon chain cinnamoyl group and 4-carbon chain cinnamoly group can be obtained. However, the homeotripic alignment using UV exposure was observed on polyitaconimide with 6-carbon chain cinnamoyl. The LC aligning ability on the polyitaconimide depends on the side chain length of photopolymer.

• Journal of International Academy of Physical Therapy Research
• /
• v.9 no.3
• /
• pp.1543-1548
• /
• 2018

The purpose of this study was to analyze the effects of manual therapy on lower extremity alignment in pelvic malalignment. The subjects were 20 adults with pelvic malalignment. They were divided into two groups: manual therapy group (n=10) and stretching exercise group (n=10). Each group performed the intervention two times per week for 4 weeks. The lower extremity alignment was measured by pelvic deviation, functional leg length inequality, and plantar pressure distribution, which were measured between pre- and post-test. In the result of pelvic deviation, there was a significant difference between the pre- and post-test of the manual therapy group and stretching exercise group. In the result of the functional leg length inequality, there was a significant difference between the pre- and post-test of the manual therapy group. In the result of plantar pressure distribution, there was a significant difference between the pre- and post-test of the manual therapy group. These findings suggest manual therapy improves the pelvic deviation, functional leg length inequality, and plantar pressure distribution in the pelvic malalignment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.357-360
• /
• 2019

We demonstrate an alignment technology using an imprinting process on an inorganic NiOx film. The aligned nanopattern was fabricated on a silicon wafer by laser interference lithography. The aligned nano pattern was then imprinted onto the sol-gel driven NiOx film using an imprinting process at an annealing temperature of $150^{\circ}C$. After the imprinting process, parallel grooves had been formed on the NiOx film. Atomic force microscopy and water contact angle measurements were performed to confirm the parallel groove on the NiOx film. The grooves caused liquid crystal alignment through geometric restriction, similar to grooves formed by the rubbing process on polyimide. The liquid crystal cell exhibited a pretilt angle of $0.2^{\circ}$, which demonstrated homogeneous alignment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.217-218
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.100-100
• /
• 2003

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1093-1094
• /
• 2011

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.185-190
• /
• 2016

Damages of the main engine aftmost bearing and the after stern tube bearing tend to increase due to misalignment. And as the shafting system becomes stiffer due to the large engine power, whereas the hull structure becomes more flexible due to optimization by using high tensile thin steel plates. And this is the reason that more sophisticated shaft alignments are required. In this study, the optimum shafting alignment calculation was carried out, considering the thermal expansion effect, exploiting the sensitivity index, which indicates the reasonable position of forward intermediate shaft bearing for shaft alignment. and as the main subject in this study, the elastic deformation on intermediate shaft and main engine bearings occurred by vertical load of shaft mass were examined thoroughly and analyzed allowable load of bearings, reaction influence numbers of all bearings. As the result, a reliable optimum shafting alignment was derived theoretically. To verify these results, they were referred to the engine maker's technical information of main engine installation and being used shafting alignment programs of both Korean Register of Shipping and Det Norske Veritas, their reliability were reviewed.

• Journal of Sensor Science and Technology
• /
• v.21 no.6
• /
• pp.440-445
• /
• 2012

Contact-type Linear Encoder-like Capacitive Displacement Sensor (CLECDiS) is a novel displacement sensor which has wide measurable range with high resolution. The sensor, however, is very sensitive to relative rotational alignment between stator and mover of the sensor as well as its displacement. In addition to, there can be some disturbances in the relative rotational alignment, so some noises occur in the sensor's output signal by the disturbances. This negative effect of the high sensitivity may become larger as increasing sensitivity. Therefore, this negative effect of the high sensitivity has to be compensated and reduced to achieve nanometer resolution of the sensor. In this study, a new type capacitive linear encoder with a mechanical guide is presented to reduce the relative rotational alignment problem. The presented method is not only to reduce the alignment problem, but also to assemble the sensor to the stage conveniently. The method is based on a new type CLECDiS that has mechanical guide autonomously. In the presented sensor, when the device is fabricated by micro-machining, the guide-rail is also fabricated on the surface of the sensor. By the direct fabrication of the guide-rail with high precision micro-machining, errors of the guide-rail can be reduced significantly. In addition, a manual yaw alignment is not required to obtain large magnitude of the output signal after the assembly of the sensor and the stage. The sensor movement is going to follow the guide-rail automatically. The prototype sensor was fabricated using the presented method, and we verify the feasibility experimentally.