• Journal of the Chungcheong Mathematical Society
• /
• v.21 no.4
• /
• pp.573-583
• /
• 2008

In this paper, we introduce the techniques of estimating the probability of failure in reliability analysis. The basic idea of each technique is explained and drawbacks of these techniques are examined.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1058-1064
• /
• 2000

The analysis of dynamic behaviour of rotor system for the rolling piston type rotary compressor considering hydrodynamic force between motor rotor and stator is presented. In addition to considering other dynamic, loads such as large unbalance forces, gas force and bearing force, we consider the hydrodynamic force induced by the compressed fluid flow through the air gap between motor rotor and stator, and improve the analysis of vibration in rotary compressor. The Childs' method which based on Bulk-now and Hirs' turbulent lubrication model is used to calculate the rotordynamic coefficients due to hydrodynamic force of annular clearance in motor air gap.

• Journal of the Korea Society for Simulation
• /
• v.28 no.1
• /
• pp.57-65
• /
• 2019

Air refueling is expected to increase the efficiency of the air force operations. This follows from the introduction of air refueling aircraft, which should to increase operational time by increasing the range and duration of fighter jets. Despite the effectiveness of the air refueling air crafts, the astronomical costs of adapting the air tankers call for careful discussions on whether to acquire any air craft and if so, how many. However there is no academic study on the subject to our knowledge. Thus, we use the ABM(Agent Based Modeling) technique to calculate the optimal number of air tankers during patrol operation. We have enhanced the reliability of the simulation by entering the specifications of the current aircraft operated by the Korean Air Force. As an optimization tool for determining the optimal number of counts, we use OptQuest built into the simulation tools and show that the optimal number of air tanker is 4.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.4
• /
• pp.173-179
• /
• 2022

Through the 2014 Donbas conflict and the 2022 Ukraine-Russia war, we are experiencing that the command of the air is no longer only secured by the Air Force. Long-range surveillance reconnaissance and strikes carried out by the Air Force could be replaced by drones and missiles, and the enemy's aerial attacks could be controlled by air defense systems such as Panchir and portable anti-aircraft missiles, allowing ground forces to carry out maneuvers freely. In other words, it is much more advantageous for the air force and the navy to take control of the air through long-distance operations, and the ground forces should support them. Therefore, this study aims to consider the cost-effectiveness aspect of the delivery command of the air; it provides implications for quickly responding to enemy air attacks by developing the air defense weapon system, drones, missiles, precision-guided munitions, etc rather than focusing on expensive fighter jets.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1B
• /
• pp.83-90
• /
• 2009

This study describes the characteristics of distribution of lift-force acting under pier deck through physical experiment. The shape of peak wave pressure was sharp when compressed air existed but was not sharp without that. Values of lift-force was different between edge point and center point in the same block. Distribution of lift-force was expressed differently owing to dimensionless of deck length (l/L), wave steepness (H/L), clearance height per wave height (D/H). The dimensionless factor of D/H affected on the lift-force the clearance between still water surface and decks. This decided the maximum of lift-force. In the case of the same values of D/H, the lift-force are changed by the wave steepness (H/L). Because (D/H) become smaller as the wave steepness (H/L) is increased the height of decks must be decided with the condition which don't have the clearance with $D_{max}$ for the stable design of deck of pier. Effect of reducing lift force was greater in the on-shore than the off-shore according to compressed air existence. This researches points out that design of deck should retain compressed air in order to reduce wave lift force.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.4
• /
• pp.158-164
• /
• 2016

Currently, identifying a new carbon-free energy resource is important in order to resolve the global warming problem. Along the same line, this paper studied how to convert magnetic force into mechanical force and a new basic mechanism of converting magnetic force into mechanical force was identified. Long-term reliability test, around 15 million times, was also conducted at $-1^{\circ}C{\sim}27^{\circ}C$ to evaluate the durability of magnetic force. As a result, tests showed that the deviation of the mechanical force was within 0.8% of the initial force, and the relation between repulsive force (P) and ambient temperature (T) was formulated in a linear equation P = -0.175T+78.945.

• Journal of Drive and Control
• /
• v.9 no.4
• /
• pp.1-7
• /
• 2012

The voice coil linear force motor is a kind of a direct drive motion device that uses a permanent magnetic field and coil winding to produce force. In order to design a voice coil linear force motor, an exact calculations of the required force, the flux density in air gap and the flux pathway are needed. A conventional method can be used usually to calculate the flux density in air gap, but with this method it is needed to find a magnetic circuit revision constant. In this paper a voice coil linear force motor is designed by conventional design method and analyzed by 3D simulation program "Flux". For the prototype linear force motor, the results of the calculated by conventional design method and the analyzed by 3D simulation program are compared with the test result. Finally it is showed that the magnetic circuit revision constant which is found by comparing of the analyzed and the measured data can be used for the design of the voice coil type linear force motor to minimize the trial and error.

• Wind and Structures
• /
• v.32 no.5
• /
• pp.487-499
• /
• 2021

The wind-blown sand effect on the high-speed train is investigated. Unsteady RANS equation and the SST k-ω turbulent model coupled with the discrete phase model (DPM) are utilized to simulate the two-phase of air-sand. Sand impact force is calculated based on the Hertzian impact theory. The different cases, including various wind velocity, train speed, sand particle diameter, were simulated. The train's flow field characteristics and the sand impact force were analyzed. The results show that the sand environment makes the pressure increase under different wind velocity and train speed situations. Sand impact force increases with the increasing train speed and sand particle diameter under the same particle mass flow rate. The train aerodynamic force connected with sand impact force when the train running in the wind-sand environment were compared with the aerodynamic force when the train running in the pure wind environment. The results show that the head car longitudinal force increase with wind speed increasing. When the crosswind speed is larger than 35m/s, the effect of the wind- sand environment on the train increases obviously. The longitudinal force of head car increases 23% and lateral force of tail increases 12% comparing to the pure wind environment. The sand concentration in air is the most important factor which influences the sand impact force on the train.

• Journal of the Semiconductor & Display Technology
• /
• v.23 no.2
• /
• pp.12-18
• /
• 2024

A Electrostatic chuck is a device that fixes the substrate, using the force between charges applied between two parallel plates to attract substrates such as wafers or OLED panels. Unlike mechanical suction methods, which rely on physical fixation, this method utilizes the force of electrostatics for fixation, making it important to verify the adhesion force. As the size of the substrate increases, deformations due to gravity or chucking force also increase, and the adhesion force decreases rapidly as the distance between the chuck and the substrate increases. The outlook for displays is shifting from small to large OLEDs, necessitating consideration of substrate deformations. In this paper, to confirm the deformation of the substrate through various patterns, a simplified 2D model using Ansys' electromagnetic field analysis program, Maxwell, and the static structural analysis program, Mechanical, was utilized to observe changes in adhesion force according to the variation in the air gap between the substrate and the chuck. Additionally, the chucking force was analyzed for the size of the substrate, and the deformation of the substrate was confirmed when gravity and chucking force act simultaneously.

• Proceedings of the KIEE Conference
• /
• 2008.04c
• /
• pp.169-171
• /
• 2008

The brake systems of the rolling stocks are generally consisted of electrical and mechanical brake systems. Because of its inherent structure of the each brake system, the electrical brake system is mainly used at the high speed range while the mechanical brake system is used at the relatively lower speed range. It is desirable for the rolling stocks to apply the entire electrical brake system. However, since the brake force from electric brake system is not enough to stop the rolling stock within the legal stop distance. Therefore, the mechanical brake system is indispensable to rolling stocks. In general, the vast majority of the world trains are equipped with mechanical braking systems which use compressed air as the force to push block on to wheels or pads on to discs. These mechanical systems are known as air brake or pneumatic brakes. For the air brake system, basically huge scale air compressor is equipped and the long pipe line is complexively connected. Since mass of these air brake components, it is difficult to be a light weight equipment and the long pipe line raise the maintenance problem. In order to overcome these problems of air brake system, the hydraulic brake system is proposed in this research. The hydraulic brake system makes the whole weight of brake equipment be light and large braking force can be applied. Therefore, in this research, the validity and advantages of applying the hydraulic brake system are reviewed.