• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.51-58
• /
• 2020

Many types of optical plastic films are essential in optoelectronics display unit fabrication and it is important to develop high precision laser cutting methods of optical films with extremely low level of film surface contamination by fume particles. This study investigates the effects of suction and blowing air motions with air flow misalignment in removing fume particles from laser cut line by employing random particle trajectory simulation and probabilistic particle generation model. The computational results show fume particle dispersion behaviors on optical film under suction and blowing air flow conditions. It is found that suction air flow motion is more advantageous to blowing air motion in reducing film surface contamination outside designated target margin from laser cut line. While air flow misalignment adversely affects particle dispersion in blowing air flows, its effects become much more complicated in suction air flows by showing different particle dispersion patterns around laser cut line. It is required to have more careful air flow alignment in fume particle removal under suction air flow conditions.

• International Journal of Safety
• /
• v.2 no.1
• /
• pp.34-38
• /
• 2003

The lower and upper flash points of the flammable binary system, butylacetate+2-propanol were measured by air blowing tester. The shape of the concentration-temperature region of flash depended on the components of the mixture in solution. The experimental data were compared with the values calculated by the reduced model under an ideal solution assumption and the flash point-prediction models based on Van Laar equation. Good qualitative agreement was obtained with these models. The prediction results of these models can thus be applied to incorporate inherently safer design for chemical process, such as the determination of the safe storage conditions for flammable solutions.

• Textile Coloration and Finishing
• /
• v.28 no.2
• /
• pp.77-91
• /
• 2016

Recently, the spun blend yarns with staple fibers and filaments are being developed in the spinning process using an air blowing and electrostatic spinning technology(cyclone) in order to enhance the soft feeling and the fine count spun blend yarn manufacturing competitiveness. In this study, the appropriate separation condition of polyester multifilament was examined according to the treatment condition of conductive agents and voltage on polyester multifilament in the newly developed cyclone spinning process. And it was investigated the physical properties and dyeability of the cyclone wool/polyester spun blend yarns and its wool composite fabrics in comparison with existing sirofil wool/polyester spun blend yarn and its fabrics. As the result, it is determined that the newly developed cyclone wool/polyester spun blend yarn applied fabrics has a superior quality level in terms of practicality.

• Applied Chemistry for Engineering
• /
• v.22 no.6
• /
• pp.664-671
• /
• 2011

The vacuum residue of petroleum refinery, i.e. asphalt, was modified through a non-catalytic air blowing process to prepare the semi-blown asphalt. Changes in composition, chemical structure, and physical properties of asphalt were examined. The result from the thin layer chromatography showed that the asphaltene content in asphalt was increased by the air blowing on account of the aromatization of aliphatic hydrocarbon and condensation. These changes in molecular structure were also confirmed by $^1H-NMR$, differential scanning calorimetry, and thermogravimetry. Because of the molecular structure changes, the penetration of asphalt was decreased and the softening point and the flash point of asphalt were increased.

• Food Science and Preservation
• /
• v.22 no.1
• /
• pp.154-157
• /
• 2015

To maintain the freshness and to prevent browning of cut Kimchi cabbages, the effect of the cutting process using a ceramic knife under $N_2$ blowing on the quality of the cut Kimchi cabbages was investigated. Kimchi cabbages cut with a ceramic knife under $N_2$ gas blowing conditions (NC) were stored at $5^{\circ}C$ for 7 days, and their weight reduction ratio and the browning degree and appearance were compared with those of the control treatment samples (OS; cut with a stainless steel knife under normal air, OC; cut with a ceramic knife under normal air). The weight reduction ratios were 0.07~0.13%, and the NC treatment showed the lowest reduction ratio among all the treatments (p<0.05). The Hunter L values increased, but the a and b values decreased after 5-day storage in all the treatments. The NC treatment had higher L values but lower a and b values than the OS and OC treatments. The browning degrees by Hunter color value, PPO activity, and appearances were the least in the NC treatment (p<0.05). The cutting process with a ceramic knife under $N_2$ blowing could be applied to the cutting of vegetable products and for minimal fruit processing.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.5
• /
• pp.25-32
• /
• 2009

A study is conducted to improve the suction performance on suction devices which are used to remove polluted air generated by welding or machining process in a spacious working place of industry. Air-curtain is applied around the inlet of suction duct to interrupt the inflow of fresh air from the downstream region where is located opposite to the polluted air source. Two different air-curtain devices, such as a $45^{\circ}$ backward and a fully backward, are adopted. Suction region is experimentally investigated by measuring the suction velocities using a hot-wire anemometer. Contours of the suction velocity are compared with the computed results. The suction condition is selected to 110,000 Reynolds number which is widely used on typical suction devices, and a width of blowing passage for creating the air-curtain is chosen to 9.38% of the suction duct diameter. The experimental results show that the suction performance obtained with the $45^{\circ}$ backward air-curtain was better than that obtained with the fully backward air-curtain. On the suction duct using the $45^{\circ}$ backward air-curtain, the suction region estimated on basis of the 0.4m/sec is improved by 66% at the same input power.

• Food Engineering Progress
• /
• v.21 no.2
• /
• pp.110-115
• /
• 2017

This study aimed to identify milling characteristics depending on the number of a cutting roller's air vent and blowing velocity to remove rice bran by the cutting type milling machine which can minimize the conventional milling process. The level of whiteness was found to be $38{\pm}0.5$ in all the conditions, showing consistent whiteness levels during milling. The rice temperatures turned out to be 15.4 and $14.6^{\circ}C$ which were rather low-level under the conditions of the cutting roller with 3 vents and blowing velocities of 35 and 40 m/s respectively. Cracked rice ratio was 2.13% under the conditions of the cutting roller with 3 vents and a blowing velocity of 35 m/s. Broken rice ratio showed the range of 0.762-0.869%, reflecting a low level. Turbidity after milling was decreased, as blowing velocity became faster. Energy consumption for milled rice production was decreased, as blowing velocity became faster. The optimum milling condition for cutting type milling machine depending on air vent number of cutting roller and blowing velocity was found to be 3 vents and 35 m/s.

• Korea-Australia Rheology Journal
• /
• v.13 no.1
• /
• pp.1-12
• /
• 2001

This paper describes the application of our recently developed two-phase model for flow-induced crystallization (FIC) to the simulation of fiber spinning and film blowing. 1-D and 2-D simulations of fiber spinning include the combined effects of (FIC), viscoelasticity, filament cooling, air drag, inertia, surface tension and gravity and the process dynamics are modeled from the spinneret to the take-up roll device (below the freeze point). 1-D model fits and predictions are in very good quantitative agreement with high- and low-speed spinline data for both nylon and PET systems. Necking and the associated extensional softening are also predicted. Consistent with experimental observations, the 2-D model also predicts a skin-core structure at low and intermediate spin speeds, with the stress, chain extension and crystallinity being highest at the surface. Film blowing is simulated using a "quasi-cylindrical" approximation for the momentum equations, and simulations include the combined effects of flow-induced crystallization, viscoelasticity, and bubble cooling. The effects of inflation pressure, melt extrusion temperature and take-up ratio on the bubble shape are predicted to be in agreement with experimental observations, and the location of the frost line is predicted naturally as a consequence of flow-induced crystallization. An important feature of our FIC model is the ability to predict stresses at the freeze point in fiber spinning and the frost line in film blowing, both of which are related to the physical and mechanical properties of the final product.l product.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.571-580
• /
• 2016

In this paper, performance of the gas turbine combined cycle(GTCC) using pre-combustion carbon capture technology was comparatively analysed. Steam reforming and autothermal reforming were used. In the latter, two different methods were adopted to supply oxygen for the reforming process. One is to extract air form gas turbine compressor (air blowing) and the other is to supply oxygen directly from air separation unit ($O_2$ blowing). To separate $CO_2$ from the reformed gas, the chemical absorption system using MEA solution was used. The net cycle efficiency of the system adopting $O_2$ blown autothermal reforming was higher than the other two systems. The system using air blown autothermal reforming exhibited the largest net cycle power output. In addition to the performance analysis, the influence of fuel reforming and carbon capture on the operating condition of the gas turbine and the necessity of turbine re-design were investigated.

• Textile Coloration and Finishing
• /
• v.12 no.3
• /
• pp.207-217
• /
• 2000

A new, high-efficiency ultrasonic fabric washing machine was developed to be an energy-efficient washing machine and to enhance fabric washing quality in washing processes of the dyeing and finishing process in the textile industry. This system is composed of ultrasonic wave generator, air blowing nozzle, torque motor for fabric tension control, and enclosed washing bath, multi-tube type exchanger, noiseless heater, air cylinder, expander roller, mangle upper and lower rollers, bend bar, dancer, shower spray nozzle, and solenoid valve, and so on. These elements are synergised for fabric washing. One of the very important principles is the low tension fabric running system. For an efficient washing effect, a counter flow system is also adopted. The new system also adopts the dancer and torque motor to control fabric tension and prevent fabric creasing. Shower spray nozzle, counter flow and overflow apparatus, and air-blowing apparatus are adopted to enhance the fabric washing effect. In this study, peach yoryu, exter, and moss crepe fabrics were washed by the general and ultrasonic washing systems under different conditions respectively. The washing efficiency was affected by the fabric running speed and characteristics of fabrics. Size content after washing increased with increasing the fabric running speed. The values in the general washing system were higher than those of the ultrasonic washing system. The changes of conductivity in the ultrasonic and the cooling bath were affected by the running time under the ultrasonic generating. The values of conductivity decreased as the experimental time passed.