• Journal of Environmental Science International
• /
• v.15 no.7
• /
• pp.659-667
• /
• 2006

This research aims at applicability of adsorption process in order to satisfy the restricted Effluent Quality Standards for dyeing wastewater. The dyeing wastewater treated by biological process with carrier imbedded microorganisms was directly applied to the activated carbon adsorption in Process A, The dyeing wastewater treated by Fenton oxidation for the effluent of biological process was applied to the adsorption in Process B. It was found that the optimum conditions of adsorption with granular activated carbon are $20^{\circ}C$ and 120 minutes for the batch experiment. Langmuir equation was fitted better than Freundlich equation to the experimental data. The breakthrough time of adsorption column was determined by color rather than $COD_{Mn}$ for both Process A and Process B. The results revealed that the breakthrough time of adsorption for two processes was extended by the treatment of Fenton oxidation for dyeing wastewater treated by biological treatment than the direct application of dyeing wastewater treated by the biological treatment. Adsorption process can be applied in order to meet the restricted Effluent Quality Standards for dyeing wastewater.

• Journal of Korean Society on Water Environment
• /
• v.22 no.3
• /
• pp.498-503
• /
• 2006

Adsorption features of $Cd^{2+}$ on waste tire particles have been investigated for the purpose of enhanced wastes recycling along with the development of an economic process for wastewater treatment. The isoelectric point of waste tire particles was found to be ca. pH 7 and the adsorbed amount of $Cd^{2+}$ was increased with pH under experimental conditions. The variation of the adsorption behavior of $Cd^{2+}$ with pH was well explained by the change of the electrokinetic potential of waste tire particles according to the pH. Adsorption of $Cd^{2+}$ was observed to reach its equilibrium within 45 minutes after the adsorption started under experimental conditions and followed the Freundlich model well. Kinetic analysis showed that the adsorption reaction of $Cd^{2+}$ was second order and thermodynamic estimation substantiated the endothermic behavior of $Cd^{2+}$ adsorption. As the amount of adsorbent increased, more adsorption of $Cd^{2+}$ was accomplished and the adsorption capacity of adsorbent was found to be enhanced by its pre-treatment with NaOH. Also, the adsorption of adsorbate was promoted as the ionic strength of wastewater was increased.

• Journal of Korean Society of Water and Wastewater
• /
• v.8 no.1
• /
• pp.34-43
• /
• 1994

It is well known that the adsorption character of activated carbon is dependent on the specific surface area and pore volume, but the relationship between the surface-chemical structure and the adsorption character has not been studied very often. The purpose of this study is to investigate the effect of the acidic surface functional groups of activated carbon and the adsorption characteristics of low concentration phenol. So three types of activated carbons and four different treatments were introduced to this isotherm experiment. These treatments were nontreatment, 1N $HNO_3$ treatment, 6N $HNO_3$ treatment, $H_2O_2$ treatment. The conclusions of this study are as followings. If the initial concentration of phenol is high as 5mg/l, the adsorption is dependent on the specific surface area. If the initial concentration of phenol is low as $100{\mu}g/l$, the adsorption is dependent on the average pore volume. The acidic surface functional groups prevent the adsorption of phenol molecules to activated carbon. And the adsorbed amount decreases more for $HNO_3$ treatment than for $H_2O_2$ treatment and more for concentrated $HNO_3$ treatment than for dilute $HNO_3$ treatment.

• Journal of the Korean institute of surface engineering
• /
• v.25 no.3
• /
• pp.144-149
• /
• 1992

The adsorption and molecular sieve characteristics of water, methanol, ethanol, butanol and benzene on acid-alkali treated natural zeolite from Kampo area were investigated by the Diamond·Kinter method, and it was compared with synthetic zeolite A. Adsorption amount of water increased with the treatment of acid rather than the treatment of alkali. Similar tendency was observedd in adsorption of alcohols such as methanol, ethanol and butanol, but the amount of adsorption decreased. From the views of the molecular size, adsorption amount of benzene decreased because of surface activity according to the cations species rather than chemical treatment. And it was almost same value that the amount of adsorption was compared acid treated natural zeolite with synthetic zeolite A.

• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.6
• /
• pp.425-435
• /
• 2020

Numerous chemical modifications on activated carbon such as acidic conditioning, thermal treatment and metal impregnation have been investigated to enhance adsorption capacities of micropollutants in water treatment plants. In this study, chemical modification including acidic, alkaline treatment, and iron-impregnation was evaluated for adsorption of 2,4-dichlorophenol (2,4-DCP). For Fe-impregnation, three concentrations of ferric chloride solutions, i.e., 0.2 M, 0.4 M, and 0.8 M, were used and ion-exchange (MIX) of iron and subsequent thermal treatment (MTH) were also applied. Surface properties of the modified carbons were analyzed by active surface area, pore volume, three-dimensional images, and chemical characteristics. The acidic and alkaline treatment changed the pore structures but yielded little improvement of adsorption capacities. As Fe concentrations were increased during impregnation, the active adsorption areas were decreased and the compositional ratios of Fe were increased. Adsorption capacities of modified ACs were evaluated using Langmuir isotherm. The MIX modification was not efficient to enhance 2,4-DCP adsorption and the MES treatment showed increases in adsorption capacities of 2,4-DCP, compared to the original activated carbon. These results implied a possibility of chemical impregnation modification for improvement of adsorption of 2,4-DCP, if a proper modification procedure is sought.

• Carbon letters
• /
• v.11 no.1
• /
• pp.34-37
• /
• 2010

In this work, graphite nanofibers (GNFs) were prepared by ammonia and heat treatment at temperatures up to $1000^{\circ}C$ to improve its $CO_2$ adsorption capacity. The effects of the heat treatment on the textural properties and surface chemistry of the GNFs were investigated by $N_2$ adsorption isotherms, XRD, and elemental analysis. We found that the chemical properties of GNFs were significantly changed after the ammonia treatment. Mainly amine groups were formed on the GNF surfaces such as lactam groups, pyrrole and pyridines. The GNFs treated at $500^{\circ}C$ showed highest $CO_2$ adsorption capacity of 26.9 mg/g at 273 K in this system.

• Applied Chemistry for Engineering
• /
• v.27 no.1
• /
• pp.62-67
• /
• 2016

In this study, a pellet-type adsorbent was prepared by using the water-treatment sludge as a raw material, and its physical and chemical properties were analyzed through $N_2$-adsorption, XRD, XRF, and $NH_3$-TPD measurements. Adsorption performance for gaseous ammonia and formaldehyde was compared between the pellet-type adsorbents prepared from water-treatment sludge and the impregnated activated carbon. Although the surface area and pore volume of the pellet-type adsorbent produced from water-treatment sludge were much smaller than those of the impregnated activated carbon, the pellet-type adsorbent produced from water-treatment sludge could adsorb ammonia gas even more than that of using the impregnated activated carbon. The pellet-type adsorbent prepared from water-treatment sludge showed a superior adsorption capacity for ammonia which can be explained by chemical adsorption ascribed to the higher amount of acid sites on the pellet-type adsorbent prepared from water-treatment sludge. In the case of formaldehyde adsorption, the impregnated activated carbon was far superior to the adsorbent made from the water-treatment sludge, which can be attributed to the increased surface area of the impregnated activated carbon.

• Carbon letters
• /
• v.2 no.2
• /
• pp.109-112
• /
• 2001

For the adsorption of ammonia, activated carbon fibers (ACFs) were subjected to sulfuric acid treatment in order to modify the surface functional groups. The surface acid and base value of ACFs were measured using titration and FT-IR spectrometry. SEM was used to investigate the surface morphology. Acid treatments by $H_3PO_4$, $H_2SO_4$, and $HNO_3$ were performed to increase the adsorption capacity of $NH_3$. As a result, Cellulose-based ACF has high adsorption capacity for ammonia. The ammonia removal efficiency of ACF was the maximum which was treated by 15 wt% sulfuric acid at $100^{\circ}C$ for 60 min. The average pore diameter little increased from $19{\AA}$ to $20.8{\AA}$ and the specific surface area of ACF considerably decreased and acid values increased by 15 wt% sulfuric acid treatment. Ammonia reacted with sulfonyl radicals. After adsorption of ammonia, white material was grown on the surface of ACF through the adsorption of ammonia and it was determined to ammonium sulfate.

• Korean Chemical Engineering Research
• /
• v.53 no.4
• /
• pp.503-508
• /
• 2015

The adsorption characteristics of ammonia on MSWI bottom ash were investigated. The effect of the variation of the landfill environmental parameters including pH, anions and organic matter on the adsorption process was discussed. Results showed that the adsorption could be well described by pseudo-second-order kinetics and Langmuir model, with a maximum adsorption capacity of 156.2 mg/g. The optimum adsorption of ammonia was observed when the pH was 6.0. High level of ion and organic matter could restrict the adsorption to a low level. The above results suggested that MSWI bottom ash could affect the migration of ammonia in the landfill, which is related to the variation of the landfill circumstance.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.6
• /
• pp.1596-1600
• /
• 2010

Surface functionalization of multi-walled carbon nanotubes (MWNTs) was carried out by means of acid treatment. The presence of oxygen functional groups on the surface of acid-treated MWNTs was confirmed with the aid of Fourier transform infrared spectroscopy and X-ray spectroscopy. In addition, carboxylic groups generally formed on the surface of acid-treated MWNTs, and the dispersion was increased by the duration of the acid treatment. The zeta-potential indicated the surface charge transfer and the dispersion of MWMTs. Morphological characteristics of acid-treated MWNTs were also observed using a transmission electron microscopy, X-ray diffraction, and Raman analysis, which was revealed the significantly unchanged morphologies of MWNTs by acid treatment. The hydrogen adsorption capacity of the MWNTs was evaluated by means of adsorption isotherms at 77 K/1 atm. The hydrogen storage capacity was dependent upon the acid treatment conditions and the formation of oxygen functional groups on the MWNT surfaces. The latter have an important effect on the hydrogen storage capacity.