• Applied Chemistry for Engineering
• /
• v.7 no.1
• /
• pp.145-152
• /
• 1996

A fine oil-in-water (O/W) emulsion using nonaqueous emulsification technique was developed and the behaviors of POE(25)octyldodecyl ether in nonaqueous solvent/oil systems were studied by observing the surface tension, interfacial tension, turbidity and transition temperature. It was found that POE(25)octyldodecyl ether existed soluble in nonaqueous solvent while, in aqueous system, it formed micelles. So, when a solvent, like glycerine in which POE(25)octyldodecyl ether has poor solubility, was added, POE(25)octyldodecyl ether moved to the surface. After saturated at surface, POE(25) octyldodecyl ether began to precitate. The mean particle size of the final emulsion was 230nm. Also, the emulsion system was stable at 0, 25, 40, $50^{\circ}C$ and cycling test for a month, while the conventional emulsion system showed unstability. It is concluded that, by pertinent combination of solvents, the adsorption efficiency of surfactant could be improved.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.63-63
• /
• 2010

Using both experimental and theoretical approaches, we have investigated the adsorption properties of an organic molecule (HATCN), which is used in OLEDs as an efficient hole injection layer, on metal and inert surfaces. We have also studied the structural and electronic properties of such interfaces and the dependences on deposition thickness. We have observed different trends in work function changes with different surfaces. Our photoelectron spectroscopic measurements have revealed an abnormal phenomenon in HATCN on a metal (Cu) surface: the work function decreases at lower coverage (~monolayer) of HATCN on a metal (Cu) surface, but it increases back and becomes higher than that of a bare Cu surface at higher coverage. It has, on the contrary, been observed that the work function of graphene surface just increases as the HATCN coverage increases. Our first-principles density functional calculations has not only verified our experimental observations, but also disclosed the underlying mechanism of such abnormal and different work function behaviors. We have found that the change in work function results from mutual polarization induced by the geometrical deformation and the bond dipole formed at the interface due to the charge redistribution. At low coverage of HAT-CN on Cu substrate, the former reduces the work function significantly by pulling down the vacuum level, while the latter tends to push up the vacuum level resulting in the work function increase.

• Journal of Wetlands Research
• /
• v.14 no.4
• /
• pp.629-635
• /
• 2012

This study was conducted to evaluate the removal behaviors of DOM(dissolved organic matter) and phosphorus in eutrophic lake water by coagulation process with PAC(powdered activated carbon). It was observed that the removal characteristic of soluble matter was different from that of dissolved one, and the removal of DOM was effected by both pH and coagulant dosage. It was founded that PAC could increase the removal efficiency by an adsorption of DOM in coagulation process. A formation of soluble and colloidal matters resulted in the degradation of phosphorus removal efficiency in a chemical precipitation process. The phosphorus removal efficiency could be enhanced by an absorption of colloidal matter and dissolved complex with PAC addition. In addition, the PAC addition caused the increase of floc density in coagulation process, that led to the rise of sedimentation rate, and resulted in a significant improvement of solid-liquid separation efficiency.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.556-556
• /
• 2012

Transition metal-based organometallic complexes have shown great talents as a catalyst in various reactions. Designing organic molecules and coordinating them to such active centers have been a promising route to control the catalytic natures. Metallocene, which has transition metal atoms sandwiched by aromatic rings, is one of the representative systems for organometallic catalysts. Group 4-based metallocene catalysts have been most commonly used for the production of polyolefins, which have great world-wide markets in the real life. Graphenes and carbon nanotubes (CNTs) were composed of extended $sp^2$ carbon networks, showing high electron mobility as well as have extremely large steric bulkiness relative to metal centers. We were inspired by these characteristics of such carbon-based nano-materials and assumed that they could intimately interact with active centers of metallocene catalysts. We examined this hypothesis and, recently, reported that CNTs dramatically changed catalytic natures of group 4-based catalysts when they formed hybrid systems with such catalysts. In conclusion, we produced hybrid materials composed of group-4 based metallocenes, $Cp_2ZrCl_2$ and $Cp_2TiCl_2$, and carbon-based nano-materials such as RGO and MWCNT. Such hybrids were generated via simple adsorption between Cp rings of metallocenes and graphitic surfaces of graphene/CNT. The hybrids showed interesting catalytic behaviors for ethylene polymerizations. Resulting PEs had significantly increased Mw relative to those produced from free metallocene-based catalytic systems, which are not adsorbed on carbon-based nano-materials. UHMWPEs with extremely high Mw were obtained at low Tp.

• Analytical Science and Technology
• /
• v.8 no.4
• /
• pp.675-682
• /
• 1995

Thin films of buckminsterfullerene($C_{60}$) formed by solution drop casting on Pt foil electrode surfaces were studied by cyclic voltammetry(CV) in acetonitrile(MeCN) containing quaternary ammonium or alkali-metal salts as supporting electrolyte. The electrochemical behaviors of $C_{60}$ films are found to be strongly dependent on the nature of the supporting electrolytes, especially with tetrabutyl ammonium perchlorate (TBAP, $NBu_4ClO_4$), and tetrabutyl ammonium tetrafluoroborate ($TBABF_4$, $NBu_4BF_4$). Reasonably stable films are formed into which electrons can be injected. The interaction of $C_{60}$ film with the quaternary ammonium cation may produce the fulleride salts $(TBA^+)(C{_{60}}^-)$ and $(TBA^+)_2(C{_{60}}^{2-})$. The bulk electroreduction with a controlled potential to generate the soluble $C{_{60}}^{3-}$ anions(dark red-brown color) is followed by electrooxidative deposition to produce a neutral $C_{60}$ film on the surface. The peak currents($I_{pc}$ and $I_{pa}$) of these thin film were dramatically decreased with repetitive potential scanning. These results could be explained by the adsorption-desorption phenomena and ion pairing interaction of reduced species($C{_{60}}^-$, and $C{_{60}}^{2-}$) onto the electrode surface. The peak current changes and peak potential shifts of the thin $C_{60}$ film in cyclic voltammograms formed from solution were observed by varying scan rates.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.17 no.2
• /
• pp.89-96
• /
• 2011

A three dimensional ecological model(EMT-3D) was applied to Ulsan Bay for the simulation of Dioxins. The simulated results of dissolved Dioxins were in agreement with the observed values, with a correlation coefficient(R) of 0.7951 and a coefficient of determination($R^2$) of 0.6265. The results of sensitivity analysis showed that partition rate, adsorption rate and bioconcentration factor were important factors. Therefore, the parameters must be carefully considered in the modeling. In the case of 50% and 80% total loads reduction, concentration of dissolved Dioxins was shown to be lower than 0.150 and 0.250 pg WHD-TEQ/L, respectively.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.04a
• /
• pp.99-101
• /
• 1998

1. Introduction : The conventional grafting polymerization technique requires chemically reactive groups on the surface as well as on the polymer chains. For this reason, a series of prefunctionalization steps are necessary for covalent grafting. The surface prefunctionalizational technique for grafting can be used to ionization radiation, UV, plasma, ion beam or chemical initiators. Of these techniques, radiation method is one of the useful methods because of uniform and rapid creation of active radical sites without catalytic contamination in grafted samples. If the diffusion of monomer into polymer is large enough to come to the inside of polymer substrate, a homogeneous and uniform grafting reaction can be carried out throughout the whole polymer substrate. Radiation-induced grafting method may attach specific functional moieties to a polymeric substrate, such as preirradiation and simultaneous irradiation. The former is irradiated at backbone polymer in vacuum or nitrogen gas and air, and then subsequent monomer grafting by trapped or peroxy radicals, while the latter is irradiated at backbone polymer in the presence of the monomer. Therefore, radiation-induced polymerization can be used to modification of the chemical and physical properties of the polymeric materials and has attracted considerable interest because it imparts desirable properties such as blood compatibility. membrane quality, ion excahnge, dyeability, protein adsorption, and immobilization of bioactive materials. Synthesizing biocompatible materials by radiation method such as preirradiation or simultaneous irradiation has often used $\gamma$-rays to graft hydrophilic monomers onto hydrophobic polymer substrates. In this work, in attempt to produce surfaces that show low levels of anti-fouling of bovine serum albumin(BSA) solutions, hydroxyethyl methacrylate(HEMA) was grafted polypropylene membrane surfaces by preirradiation technique. The anti-fouling effect of the polypropylene membrane after grafting was examined by permeation BSA solution.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.21 no.1
• /
• pp.19-37
• /
• 1995

A fine oil -in-water (O/W) emulsion using non-aqueous emulsification technique was developed. And the behaviors of POE(25)octyldodecyl ether in non-aqueous polyol/oil systems were studied by observing the surface tension, interfacial tension, turbidity and transition temperature. It was found that POE(25)octyldodecy1 ether hardly existed as the micelle in the non-aqueous polyol system while, in water, it formed micelles very easily. So, when a polyol, like glycerine in which POE(25)octyldodecyl ether has a poor solubility, was added, POE(25)octyldodecyl ether moved to the surface. After saturated at surface, POE(25)octyldodecyl ether began to precitate. The mean particle size of the final emulsion was 230nm. Also, the emulsion system was stable at 0$^{\circ}C$, 25$^{\circ}C$, 40$^{\circ}C$, 50 $^{\circ}C$ and freeze-thaw cycle chamber for a month, while a conventional emulsion system was unstable. It is concluded that, by pertinent combination of polyols, we can improve the adsorption efficiency of surfactant.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.178-184
• /
• 2010

The aim of this work is the fabrication of polyelectrolyte microcapsules composed of biocompatible polymers such as chitosan, heparin and alginate, to encapsulate the fluorescein isothiocyanate(FITC)-albumin, and to investigate the protein release behavior therefrom. Polyelectrolyte capsules with 4-layer structures could be prepared with biocompatible materials by oppositely charged adsorption using melamin-foramide as a template. Transmission electron microscope(TEM), scanning electron microscope(SEM) and optical microscope confirmed hollow capsule structures. Protein release before and after encapsulation was monitored with a UV-Vis spectrometer. Microcapsules have different behaviors depending on the kind of polyelectrolyte polymers, chitosan-heparin capsules or chitosan-alginate capsules. In conclusion, the polyelectrolyte multilayer shells can be switched between an open and closed state by means of tuning the pH value.

• Composites Research
• /
• v.33 no.6
• /
• pp.336-340
• /
• 2020

In this study, carbon aerogels (CA) were prepared by sol-gel polycondensation of resorcinol and furfural in isopropanol using hexamethylenetetramine as a catalyst, and then directly drying the organic gels under isopropanol freeze-drying conditions, followed by carbonization under a nitrogen atmosphere. The preparation conditions of the CA were explored by changing the mole ratio of resorcinol to furfural. The effect of the preparation conditions on the pore structure of the CA was studied by nitrogen adsorption isotherms. The characteristics of the CA were studied by scanning and transition electron microscopy, and infrared spectrometry. The accessibility of pores and performance of the CA as an electrode in electric double layer capacitors were also electrochemically investigated. As a result, BET surface area and specific capacitance increased with the molar ratio of resorcinol to catalyst (R/C) ratio; the maximum values of 765 ㎡/g and 132 F/g were achieved at the R/C ratio of 200, respectively. Consequently, it was confirmed that increasing the R/C ratio increased the average pore size of the CA electrode, which improved the rate capability of the system.