• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.5
• /
• pp.80-87
• /
• 1999

We propose a new recirculating fiber delay-line filter structure. In proposed system, we insert a fiber Bragg grating(FBG) into a recirculating fiber delay line and it operates as a partially reflection mirror. Therefore, the transfer function of the system is given by the recirculating delay output part and the multiple-reflected output part due to a FBG. By adjusting the parameters such as coupling coefficient, reflectivity of FBG, and gain, we can make the system operate in various filter.

• Transactions of Materials Processing
• /
• v.19 no.4
• /
• pp.203-209
• /
• 2010

In the hot press forming process (HPF), a martensitic structure is obtained by controlling the cooling rate when cooling a boron sheet that is heated up to over $900^{\circ}C$. The HPF process has various advantages such as the improvement in formability and material properties and minimal spring back of the deformed materials. The factors related to the cooling rate depend on the heat transfer characteristics between heated materials and dies. Therefore, in this study, the cooling rate is controlled by adjusting the heat transfer coefficient of the material at the pressing process. And, the mechanical properties and microstructure of the deformed material is demonstrated during the HPF process where cold dies are used to form the heated steel plate. This is achieved by varying the major forming conditions that control the cooling rate regarded as the most important process parameter.

• ETRI Journal
• /
• v.31 no.6
• /
• pp.675-679
• /
• 2009

$Ti_xSi_{1-x}O_y$ (TSO) thin films are fabricated using plasma-enhanced atomic layer deposition. The Ti content in the TSO films is controlled by adjusting the sub-cycle ratio of $TiO_2$ and $SiO_2$. The refractive indices of $SiO_2$ and $TiO_2$ are 1.4 and 2.4, respectively. Hence, tailoring of the refractivity indices from 1.4 to 2.4 is feasible. The controllability of the refractive index and film thickness enables application of an antireflection coating layer to TSO films for use as a thin film solar cell. The TSO coating layer on an Si wafer dramatically reduces reflectivity compared to a bare Si wafer. In the measurement of the current-voltage characteristics, a nonlinear coefficient of 13.6 is obtained in the TSO films.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.1045-1046
• /
• 2015

When using the Support Vector Machine in the online signature verification, SVM kernel function should be chosen to use non-linear SVM and the constant parameters in the kernel functions should be adjusted to appropriate values to reduce the error rate of signature verification. Non-linear SVM which is built on a strong mathematical basis shows better performance of classification with the higher discrimination power. However, choosing the kernel function and adjusting constant parameter values depend on the heuristics of the problem domain. In the signature verification, this paper deals with the problems of selecting the correct kernel function and constant parameters' values, and shows the kernel function and coefficient parameter's values with the minimum error rate. As a result of this research, we expect the average error rate to be less than 1%.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.4
• /
• pp.168-173
• /
• 2012

The aggregation of group loads, which consists of the linear and the non-linear systems, yields the error involved in the reactive power aggregation, which is greater than the active power aggregation in the component based load modeling. Each individual reactive power in a group load affects the aggregated load different from composition rate. This paper proposes a new method that determines the degree of impacts by adjusting the coefficient of weight factors of each load using the least squares error method. The effectiveness of proposed algorithm is demonstrated by simulating three aggregation cases.

• Journal of electromagnetic engineering and science
• /
• v.6 no.1
• /
• pp.53-61
• /
• 2006

In this paper, we present parametric studies for the optimum design of a hexagonal plate monopole antenna. The dependence of the antenna performance on various geometric parameters is investigated using a commercial electromagnetic software, from which an optimum design of a hexagonal plate monopole antenna is derived. Guidelines for determining initial parameter values are given. The diameter of the circular ground plane is minimized tlo 1/5 wavelength at the lowest operating frequency. The antenna impedance matching is controlled by adjusting the gap between the plate and the ground plane, the plate base width, and the base bevel angle. The antenna proposed in. this paper shows a reflection coefficient less than -10 dB and a $2.0{\sim}6.2$ dBi gain over $3{\sim}20$ GHz frequencies.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.371-372
• /
• 2015

Dc microgrid has the advantage of high efficiency as compared to the ac system. Droop method has been realized to suppress the current mismatching among the distributed sources. However, this method involves distribution loss due to the line impedance. In this paper, a novel droop method is proposed to minimize the distribution loss as well as the voltage deviation by adjusting the droop coefficient. The proposed droop method is verified by using the simulation based on PSCAD/EMTDC.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.10
• /
• pp.1445-1453
• /
• 2013

The scale-up criterion of constant oxygen mass transfer coefficient ($k_La$) was applied for the production of itaconic acid (IA) in a 50 L pilot-scale fermentor by the fungal cells of Aspergillus terreus. Various operating conditions were examined to collect as many $k_La$ data as possible by adjusting the stirring speed and aeration rate in both 5 L and 50 L fermentor systems. In the fermentations performed with the 5 L fermentor, the highest IA production was obtained under the operating conditions of 200 rpm and 1.5 vvm. Accordingly, we intended to find out parallel agitation and aeration rates in the 50 L fermentor system, under which the $k_La$ value measured was almost identical to that ($0.02sec^{-1}$) of the 5 L system. The conditions of 180 rpm and 0.5 vvm in the 50 L system turned out to be optimal for providing almost the same volumetric amount of dissolved oxygen (DO) into the fermentor, without causing shear damage to the producing cells due to excessive agitation. Practically identical fermentation physiologies were observed in both fermentations performed under those respective operating conditions, as demonstrated by nearly the same values of volumetric ($Q_p$) and specific ($q_p$) IA production rates, IA production yield ($Y_{p/s}$), and specific growth rate (${\mu}$). Specifically, the negligible difference of the specific growth rate (${\mu}$) between the two cultures (i.e., $0.029h^{-1}$ vs. $0.031h^{-1}$) was notable, considering the fact that ${\mu}$ normally has a significant influence on $q_p$ in the biosynthesis of secondary metabolites such as itaconic acid.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.3
• /
• pp.323-327
• /
• 2024

The low-temperature coefficient of resistance (TCR) is a crucial factor in the development of space-grade resistors for temperature stability. Consequently, extensive research is underway to achieve zero TCR. In this study, resistors were deposited by co-sputtering nickel-chromium-based composite compositions, metals showing positive TCR, with SiO₂, introducing negative TCR components. It was observed that achieving zero TCR is feasible by adjusting the proportion of negative TCR components in the deposited thin film resistors within certain compositions. Additionally, the correlation between TCR and deposition conditions, such as sputtering power, Ar pressure, and surface roughness, was investigated. We anticipate that these findings will contribute to the study of resistors with very low TCR, thereby enhancing the reliability of space-level resistors operating under high temperatures.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.2 s.48
• /
• pp.63-71
• /
• 2006

In the companion paper (II, Development of Site Classification System), new size classification system based on site periods $(T_G)$ was recommended for legions of shallow bedrock depth in Korea. Despite the site classification method was improved, the response spectrum would be required to be modified by adjusting the integration interval to calculate the site coefficients because the response spectra did not match well the average spectral accelerations obtained by site response analyses in the range of long periods. In this paper, new response spectra for each site categories were determined by adjusting the integration interval of long period site coefficient $F_v\;from\;0.4{\sim}2.0\;to\;0.4{\sim}1.5$ second. It matched well the average spectral accelerations and new response spectrum, and it was also improved compared to the current she classification system.