• 한국멀티미디어학회논문지
• /
• 제14권3호
• /
• pp.414-422
• /
• 2011

본 연구는 얇은 유전체기판 위에 프린트 패턴으로 구현하는 상/하 대칭 루프안테나에 관한 것으로서, 유전체기판 상/하에 대칭으로 루프안테나용 동박패턴을 제작하여 기판의 상/하에 프린트된 루프패턴 간에서 방사되는 전자계가 서로 충돌하지 않게 방사되는 위상제어형 상/하 대칭 루프안테나에 관한 것이다. 이 방법으로 상/하에 프린트된 각 루프코일이 서로 동위상으로 보완적으로 배치되어 전자계가 원만하게 방사되어, 방사 손실이 없고 방사 효율이 뛰어나게 된다. 앓은 유전체기판의 상/하에 프린트하여 안테나를 구현함으로 연해 경박/소형화가 가능해지며, 이로 인하여 크기 $40mm{\times}6mm$ 이하의 사이즈에, 두께 0.2mm 이하의 박막의 유전체가판에 제 3세대 휴대폰대역인 WCDMA 안테나를 구현하여 액티브 시험에서 평균게인 -3dBi 이상 방사효율 50~70% 정도의 안테나특성이 얻어졌으며, 상용되는 이동형 멀티미디어단말기에 부착하여 액티브 시험결과 평균게인 -4dBi, 송/수신 효율이 43% 얻어졌다.

• 대한치과보철학회지
• /
• 제31권2호
• /
• pp.165-179
• /
• 1993

Dicor has not been prescribed routinely, in spite of many advantages, because of esthetic limitations by excessive translucency and external shading. In an attempt to solve these problems, the technique of veneering Dicor by aluminous poreclain has been used and recently Dicor Plus system was developed. The purpose of this study was to evaluate the compatibility between Dicor and several veneering porcelains by measuring the shear bond strength and observing the failure mode and interface appearance with SEM. Total 55 Dicor disks(10.0mm diam. X 3.0mm thickness) were fabricated by lost wax technique and divided into five groups of 11. Veneering porcelains such as Dicor Plus, Vitadur Alpha, Vitadur N, Vivodent, and Ceramco II were built up over the center of the treated Dicor surface using paper tube(5.0mm diam. X 4.0mm height) and fired according to the manufacturesr’instructions. A representative sample from each group was completely embedded in epoxy resin and crosssectioned, and remaining 50 samples were embedded in epoxy resin with the bonded area perpendicular to table base. The shear bond strengths were measured by applying the shear load parallel to Dicor surface close to the bonded area. Failure modes and interface appearances were observed using SEM at 15 and 1000 magnification respectively. The obtained results were as follows : 1. The mean shear bond strengths showed Dicor-Dicor Plus(10.53 MPa); Dicor-Vitadur Alpha(8.84 MPa); Dicor-Vitadur N(7.37 MPa); Dicor-Vivodent(4.28 MPa); Dicor-Ceramco II(0.89 MPa). 2. The shear bond strength of Dicor-CeramcoII was significantly decreased compared with Dicor-Dicor Plus(p<0.01), but had no significant difference compared with Dicor-Vivodent(p>0.01). 3. The shear bond strengths of Dicor-Vitadur Alpha and Dicor-Vitadur N were not significantly different compared with Dicor-Dicor Plus(p>0.01). 4. SEM examination of bond failure modes revealed that Dicor-Dicor plus, Dicor-Vitadur Alpha, Dicor-Vitadur N exhibited cohesive failure within Dicor and Dicor-Vivodent exhibited adhesive failure. And Dicor-Ceramco III exhibited adhesive failure and cohesive failure within CeramcoIII together. 5. SEM examination of interfaces revealed that Dicor-Dicor Plus exhibited the most tight contact and Dicor-Vitadur Alpha, Dicor-Vitadur N exhibited acceptible contacts. But Vivodent exhibited discontinuous gap and Ceramco II exhibited large continuous gap.

• 한국광학회지
• /
• 제34권4호
• /
• pp.157-169
• /
• 2023

헤드 마운티드 디스플레이(head mounted display, HMD)를 이용한 증강 현실(augmented reality, AR)은 군사, 의료, 제조, 게임 및 교육 등 다양한 분야에서 활용되고 있다. 본 논문에서는 HMD에 가장 필수적인 AR 광학계의 설계 및 제작에 대해 논의한다. HMD용 AR 광학계는 디스플레이의 증강 영상과 현실 세계를 동시에 볼 수 있는 넓은 투명 영역이 필요하다. 이를 위해, AR 광학계를 각각의 특성에 따라 세 부분으로 나누어 설계 및 제작하였다. 그리고 3개의 광학계를 하나의 완전한 AR 광학계로 만들기 위해 필요한 ultra-violet (UV) 접착층의 굴절률을 고려해 설계함으로써 입력 광원이 UV 접착 층을 통과할 때의 광경로 이동(shift) 현상을 최소화하였다. 또한, AR 광학계를 설계할 때 축외 수차를 보정하고 양산에 적합하도록 2개의 비구면을 사용했다. 끝으로 HMD 양산을 위해 두께 11 mm, 대각선 화각(diagonal field of view) 40°, 무게 11.3 g의 비구면 AR 광학계를 설계하고 제작하였다.

• 한국표면공학회지
• /
• 제48권2호
• /
• pp.33-37
• /
• 2015

High efficiency LED device is being concerned due to its high heat loss, and such heat loss will cause a shorter lifespan and lower efficiency. Since there is a demand for the materials that can release heat quickly into the external air, the organic insulating layer was required to be replaced with high thermal conductive materials such as metal or ceramics. Through anodizing the upper layer of Al, the Breakdown Voltage of 3kV was obtained by using an uniform thickness of $60{\mu}M$ aluminum oxide($Al_2O_3$) and was carried out to determine the optimum process conditions when thermal cracking does not occur. Two Ni layers were formed above the layer of $Al_2O_3$ by sputtering deposition and electroplating process, and saccharin was added for the purpose of minimizing the remain stress in electroplating process. The results presented that the 3-layer film including the Ni layer has an adhesive force of 10N and the thermal conductivity for heat dissipation is achieved by 150W/mK level, and leads to improvement about 7 times or above in thermal conductivity, as opposed to the organic insulation layer.

• 대한가정학회지
• /
• 제37권7호
• /
• pp.29-43
• /
• 1999

The purpose of this study was to develop disposable diapers for the elderly in need by experimenting with wearing disposable diapers and analyzing the properties of materials of these diapers. The diapers were of two different types: one was a panty type for the elderly who were bed ridden, and the other was a pad type for the elderly who had incontinence. The subjects for the wearing test of the panty type were forty who were bed ridden, and there were forty subjects for the wearing test of the pad type who had incontinence. The disposable diapers for these experiments were chosen from those already found in the market place. Four panty types and three pad types were selected. From these experiments for the disposable diapers, the first prototypes were developed, and the second prototypes were proposed by experimenting with the first prototypes. The first panty prototype was designed to improve absorbing power, and we added waist rubber bands to prevent evacuation from back leaking and a frontal tape to prevent waistline film from tearing. The first pad prototype was designed to improve absorbing power also, and we added side rubber bands to prevent the side leaking and an adhesive tape on the fore part of the bottom to prevent the diapers from moving, and made the outline of the back area curved and thin to help hide the diaper from detection thus making the wearer feel better. From these test cases and analyzing the properties of materials with the first prototypes, we gained some success, but several points on further improvements were proposed to refine the final prototypes. The second panty prototype we proposed was to make 1he length longer, especially in the crotch area to prevent excess leaking and to fit the body more snugly. Also, the second pad prototype was proposed to reduce the total thickness of the diaper, and to improve the feeling and appearance.

• Journal of the Korean Wood Science and Technology
• /
• 제45권3호
• /
• pp.360-367
• /
• 2017

본 연구에서는 단열성능 및 물리적 성질이 우수한 친환경 목섬유 단열재의 제조 기술을 확립하기 위하여 멜라민 요소 폼알데하이드(MUF), 페놀 폼알데하이드(PF), emulsified MDI (eMDI) 및 라텍스계 수지 등 서로 다른 접착제로 제조한 저밀도섬유판의 특성을 비교하였다. 그 결과 MUF, PF, eMDI 수지 접착제로부터는 경질(硬質) 저밀도섬유판이, 라텍스계 수지 접착제로부터는 연질(軟質)의 저밀도섬유판이 각각 제조되었다. 모든 저밀도섬유판은 일반 중밀도섬유판에 비해 현저히 낮은 열전도율을 나타냈으며, 압출 발포 폴리스티렌과 유사한 단열 성능을 나타내는 것으로 조사되었다. 한편 본 연구에서 제조한 저밀도섬유판 중 eMDI를 사용한 것은 흡수 두께/길이 팽창률 및 휨 강도 등 물리적 성질이 가장 우수하였다.

• 보존과학회지
• /
• 제22권
• /
• pp.61-76
• /
• 2008

청동문화재 보존처리의 강화처리제로 가장 많이 쓰이고 있는 아크릴 수지인 Paraloid B72와 용제 4종(Acetone, MEK, Toluene, Xylene)을 선정하여 각 용제별 코팅 특성을 비교 분석하였다. 코팅 전 후의 표면을 현미경과 AFM을 통해 관찰하고 박막의 두께와 코팅 표면의 접촉각을 측정하여 표면에너지를 계산하였다. 그리고 Scratch Test를 통해 코팅 박막의 접착력을, 황변실험을 통해 코팅의 지속성을 조사하였다. 그 결과 Xylene을 용제로 사용하는 것이 육안으로 보았을 때 색 얼룩이 적고 적절한 소수성과 고른 표면을 가짐을 확인했다. 또한 코팅의 조건인 박막 두께가 얇으면서 접착력이 우수하며 황변에도 안정해야 한다는 점에서도 10% Paraloid B72 in xylene이 다른 용제에 비하여 우수한 코팅 성질을 가진다는 것을 확인하였다. 그러나 Paraloid B72의 적정농도를 찾기 위해서는 더 많은 실험과 분석이 이루어져야 할 것이다.

• International Journal of Concrete Structures and Materials
• /
• 제8권1호
• /
• pp.83-97
• /
• 2014

This paper presents the results of an investigation aimed at developing reinforced concrete beams consisting of precast permanent U-shaped reinforced mortar forms filled with different types of core materials to be used as a viable alternative to the conventional reinforced concrete beam. To accomplish this objective, an experimental program was conducted and theoretical model was adopted. The experimental program comprised casting and testing of thirty beams of total dimensions $300{\times}150{\times}2,000mm$ consisting of permanent precast U-shaped reinforced mortar forms of thickness 25 mm filled with the core material. Three additional typical reinforced concrete beams of the same total dimensions were also cast to serve as control specimens. Two types of single-layer and double-layers steel meshes were used to reinforce the permanent U-shaped forms; namely welded wire mesh and X8 expanded steel mesh. Three types of core materials were investigated: conventional concrete, autoclaved aerated lightweight concrete brick, and recycled concrete. Two types of shear connections between the precast permanent reinforced mortar form and the core material were investigated namely; adhesive bonding layer between the two surfaces, and mechanical shear connectors. The test specimens were tested as simple beams under three-point loadings on a span of 1,800 mm. The behavior of the beams incorporating the permanent forms was compared to that of the control beams. The experimental results showed that better crack resistance, high serviceability and ultimate loads, and good energy absorption could be achieved by using the proposed beams which verifies the validity of using the proposed system. The theoretical results compared well with the experimental ones.

• 대한토목학회논문집
• /
• 제12권1호
• /
• pp.207-217
• /
• 1992

본 연구에서는 기체 액체 고체의 직접접촉이 일어나는 3상 유동층 반응기를 이용하여 유입상승 유속에 의한 공극률의 변화와 생물막의 두께 및 밀도를 관측하였다. COD의 용적부하율은 반송비(r=0.2, 0.4, 0.6)로 조절하여 $201.12-1150.8g/m^3{\cdot}d$로 하였으며, 고체 매질로는 연탄재입자(평균유효입경 : 1.34 mm)와 유리비드(3 mm)를 사용하여, 매질의 차이에 따른 반응기의 효율에 대하여 비교하였다. 그 결과 반송비를 일정하게 고정시킨 경우, 연탄재 매질에 의한 생물막의 두께가 유리비드를 사용한 것보다 약 4.8배 두꺼우며, COD 제거 효율은 두 매질사이에는 변화가 거의 없으나, 암모니아성 질소의 제거에는 연탄재의 경우가 약간 높았다. 반응조내의 식종균으로는 합성폐수와 유사한 배지에서 동정 분리하여낸 토양미생물을 이용하였다 이 토양미생물은 기존의 활성슬러지균 보다 점착력과 침강성이 뛰어났다.

• Tribology and Lubricants
• /
• 제33권4호
• /
• pp.127-133
• /
• 2017

In order to characterize the adhesive properties and failure mechanisms of diamond-like carbon (DLC) films of two different thicknesses (130 nm and $1.2{\mu}m$), deposited by plasma-enhanced chemical vapor deposition on a Si substrate, scratch testing with a micro-indenter ($12.5{\mu}m$ tip radius) was performed under a linearly increasing load. These scratch tests were conducted under the same test conditions for both films. The critical load of each film was estimated from the scratch test results, based on a sharp increase in the coefficient of friction and a clear distinction of failure modes. The critical load was the basis for evaluating the adhesion strength of the films, and the $1.2{\mu}m-thick$ DLC film had superior adhesion strength. For better understanding of the failure modes, the following analyses were conducted: friction behavior and scratch tracks analysis using scanning electron microscopy, energy-dispersive spectroscopy, and 3-D profilometry. The scratch test results showed that failure modes were related to the thickness of the films. The 130 nm-thick DLC film underwent cohesive failure modes (cracks and chipping) before reaching to a gross failure stage. On the other hand, the thicker DLC film ($1.2{\mu}m-thick$) did not exhibit micro cracks before a sudden gross failure of the film together with the evidence of cracking and chipping of the Si substrate.