• 구강회복응용과학지
• /
• 제37권4호
• /
• pp.209-216
• /
• 2021

목적: 본 연구의 목적은 접착제를 적용하지 않고 치열교정용 브라켓을 접착할 수 있는 레진시멘트의 법랑질에 대한 접착강도를 접착제를 적용한 경우와 비교하기 위함이다. 연구 재료 및 방법: 시편을 Transbond XT, GC Ortho Connect 및 Orthomite LC의 3개의 실험군으로 나누고, 노출된 법랑질 표면을 2분획으로 나누어 한 분획에는 37% 인산으로, 다른 한 분획에는 37% 인산 및 접착제 혹은 유니버셜 접착제로 표면 처리를 하였다. 치열교정용 브라켓에 3 종류의 시멘트를 각각 도포하고 접착을 한 뒤 전단접착강도를 측정하였다. 결과: Transbond XT와 Orthomite LC는 각각 접착제와 유니버셜 접착제를 적용한 후 치열교정용 브라켓을 접착할 경우 전단접착강도가 유의하게 증가하였다. 결론: Transbond XT와 Orthomite LC에서 산 부식 후 접착제의 적용이 치열교정용 브라켓의 전단접착강도를 향상시킬 것으로 기대한다.

• Restorative Dentistry and Endodontics
• /
• 제24권1호
• /
• pp.26-39
• /
• 1999

Bis-GMA, the representative monomer of bonding resin, contributes to the rigidity of bonding layer. Hydrophilic monomer contributes to the permeability into dentin substrates while weaken the bonding layer due to its small molecular weight. The degree of conversion also contributes to the ultimate strength of the bonding layer. This study was performed for the correlation analysis of monomer ratio and dentin bonding strength via degree of conversion. 7 experimental bonding resins were prepared with Bis-GMA, ratio from 20% to 80% by 10% increment, and hydrophilic HEMA monomer. Their degree of conversion and shear bond strength to dentin were compared with Scotchbond Multi-Purpose adhesive, and the fractured surfaces were examined microscopically. The results were as follows; 1. The degree of conversion increased when, the ratio of Bis-GMA increased from 20% to 70%, whereas it decreased when the ratio of Bis-GMA was 80%. 2. Shear bond strengths of the experimental bonding resins of 80%, 70%, 60% ratio of Bis-GMA were significantly higher than those of the experimental bonding resin of 50% ratio of Bis-GMA and Scotchbond Multi-Purpose adhesive. Lower shear bond strengths were obtained with the experimental bonding resins of 40%, 30%, 20% ratio of Bis-GMA (p<0.05). 3. Adhesive fractures were associated with the bonding resins of the lower bond strength, while cohesive fractures within the bonding resin layer were associated with the bonding resins of higher bond strength. Bonding resins with shear bond strength higher than 18MPa showed some cohesive fractures within the composite resin or within the dentin. 4. Correlations between Bis-GMA ratio and the degree of conversion (r=0.826), between Bis-GMA ratio and shear bond strength (r=0.853), and between the degree of conversion and shear bond strength (r=0.786) were significant (p<0.05).

• The Journal of Advanced Prosthodontics
• /
• 제14권4호
• /
• pp.262-272
• /
• 2022

PURPOSE. This study aimed to analyze the shear bond strength between the 3D-printed denture base and the chairside relining material, according to the surface treatment. MATERIALS AND METHODS. Cylindrical specimens were prepared using DENTCA Denture Base II. The experimental groups were divided into 6 (n = 10): no surface treatment (C), Tokuyama Rebase II Normal adhesive (A), sandblasting (P), sandblasting and adhesive (PA), sandblasting and silane (PS), and the Rocatec system (PPS). After bonding the chairside relining material to the center of the specimens in a cylindrical shape, they were stored in distilled water for 24 hours. Shear bond strength was measured using a universal testing machine, and failure mode was analyzed with a scanning electron microscope. Shear bond strength values were analyzed using one-way analysis of variance, and Tukey's honest significant difference test was used for post-hoc analysis (P < .05). RESULTS. Group PPS exhibited significantly higher shear bond strength than all other groups. Groups P and PA displayed significantly higher bond strengths than the control group. There were no significant differences between groups PS and A compared to the control group. Regarding the failure mode, adhesive failure occurred primarily in groups C and A, and mixed failure mainly in groups P, PA, PS, and PPS. CONCLUSION. The shear bond strength between the 3D-printed denture base and the chairside relining material exhibited significant differences according to the surface treatment methods. It is believed that excellent adhesive strength will be obtained when the Rocatec system is applied to 3D-printed dentures in clinical practice.

• Journal of Welding and Joining
• /
• 제31권5호
• /
• pp.71-76
• /
• 2013

The effect of zirconate having - NH functional group on the T-peel and lap shear strength of $CaCO_3$ containing structural epoxy adhesive for car body assembly was investigated. Curing behavior of epoxy adhesive samples were investigated by differential scanning calorimeter (DSC) techniques. The addition of zirconate up to 7.5 phr did not affect the curing mechanism of epoxy adhesive. While the small amount of zirconate addition less than 1.1 phr increased the cross-linking density, the excess addition of zirconate resulted in the increase of uncross-linked impurity. From the increase of T-peel and lap shear strength and the change of fracture mode from the adhesive failure to the mixed one, it was considered that the small addition of zirconate was effective in improving the adhesion strength of epoxy adhesive to the adherend and inorganic filler surfaces. The formation of uncross-linked impurity with the excess addition of zirconate was considered to decrease the joint strength by decreasing the cohesive strength of the cured epoxy.

• Journal of Welding and Joining
• /
• 제23권6호
• /
• pp.67-71
• /
• 2005

This paper is concerned with a study on fracture strength of composites in an adhesive single lap joint. The tests were carried out on joint specimens made with hybrid stacked composites consisting of the polyester and bamboo natural fiber layer. The main objective of this work was to evaluate the fracture properties adjacent to adhesive bonded joint of natural fiber reinforced composite specimens. From the results, natural fiber reinforced composites have lower tensile strength than the original polyester. But tensile-shear strength of natural fiber reinforced composites with bamboo layer far from adhesive bond is as high as that of the original polyester adhesive bonded joints. Spew filet at the end of the overlap reduced the stress concentration at the bonded area. Spew fillet and position of bamboo natural fiber layer have a peat effect on the tensile-shear strength of natural fiber reinforced composites including adhesive bonded joints.

• Steel and Composite Structures
• /
• 제20권6호
• /
• pp.1275-1303
• /
• 2016

Steel plates and carbon-fiber-reinforced polymer (CFRP) laminates or plates bonded to concrete substrates have been widely used for concrete strengthening. However, this technique cause plate debonding, which makes the strengthening system inefficient. The main objective of this study is to enhance the bond strength of externally bonded steel plates and CFRP laminates to the concrete surface by proposing new embedded adhesive and steel connectors. The effects of these new embedded connectors were investigated through the tests on 36 prism specimens. Parameters such as interfacial shear stress, fracture energy and the maximum strains in plates were also determined in this study and compared with the maximum value of debonding stresses using a relevant failure criterion by means of pullout test. The study indicates that the interfacial bond strength between the externally bonded plates and concrete can be increased remarkably by using these connectors. The investigation verifies that steel connectors increase the shear bond strength by 48% compared to 38% for the adhesive connectors. Thus, steel connectors are more effective than adhesive connectors in increasing shear bond strength. Results also show that the use of double connectors significantly increases interfacial shear stress and decrease debonding failure. Finally, a new proposed formula is modified to predict the maximum bond strength of steel plates and CFRP laminates adhesively glued to concrete in the presence of the embedded connectors.

• 대한치과교정학회지
• /
• 제30권4호
• /
• pp.483-490
• /
• 2000

치과용 금합금에 브라켓을 부착하는 경우 자연치에 비하여 낮은 결합강도를 보이며, 잦은 브라켓 탈락이 나타나고 있는 바, 본 연구는 여러 가지 금합금 표면처리 방법이 교정용 레진 접착제와 금합금 간의 전단결합강도에 미치는 영향을 평가하여 금합금과 브라켓 간의 부착강도 증진방법을 모색하고자 시행하였다. 치과용 금합금으로 주조된 240개의 시편을 표면처리 유무 및 방법에 따라 무처리, 샌드블라스팅 단독처리, 샌드블라스팅과 주석도금 병용처리, 그리고 샌드블라스팅과 중간접착제 병용처리의 4가지 경우와, Ortho-one, Panavia 21, Superbond C&B의 3가지 레진접착제의 조합에 의해 12군으로 나누어 브라켓을 부착하였다. 시편을 증류수에 담아 $37^{\circ}C$ 항온 수조 속에서 24시간 동안 보관한 후, 만능물성 시험기를 이용하여 전단결합강도를 측정한 후 다음과 같은 결과를 얻었다. 1. 치과용 금합금의 표면을 처리하지 않은 경우에 비하여 표면처리한 군에서 통계적으로 유의하게 높은 전단결합강도가 나타났다. 2. 샌드블라스팅 단독처리에 비하여 주석도금 병용처리를 시행한 경우 Panavia 21에서만 유의한 결합강도 증가가 나타났다. 3. 샌드블라스팅 단독처리에 비하여 중간접착제 병용처리를 시행한 경우 모든 접착제에서 유의한 결합강도 증가가 나타났다. 4. 사용된 레진접착제에 따른 전단결합강도를 비교한 결과 Superbond C&B가 가장 높고 그 다음으로 Panavia 21, Ortho-one 순으로 나타나는 양상을 보였다. 이상의 결과는 금합금 표면에서 브라켓 부착강도를 증가시키기 위해서는 레진접착제 종류에 관계없이 샌드블라스팅과 중간접착제 병용처리가 필요함을 시사하였다.

• Restorative Dentistry and Endodontics
• /
• 제21권1호
• /
• pp.280-288
• /
• 1996

The purpose of this study was to assess comparatively the shear bond strength on dentin of four dentin bonding agents used in conjunction with light-curing composite resins. Clearfil New Bond, Scotchbond Multipurpose Dentin Adhesive, All-Bond 2 and X-R Bond were applicated on labial dentin surfaces just below dentin - enamel juction of bovine incisor teeth. After shear bond strength testing with the universal testing machine, the bonding interface of the specimens were observed under light stereomicroscope. Following results were obtained. 1. The shear bond strength was high in the order of B,C,D,A and group B Scotchbond Multipurpose Dentine Adhesive revealed greater bond strength than Clearfil New Bond and X-R Bond. (p<.001) 2. When using ANOVA and Duncan's multiple range test, there were statistical differences among the four groups, except between group Band C,group D and A. 3. There was no relationship between mode of failure and shear bond strength.

• Composites Research
• /
• 제33권5호
• /
• pp.275-281
• /
• 2020

본 논문에서는 항공기 팬 블레이드에 적용되는 복합재와 금속 간의 접합 구조물에 대한 온도, 습도에 따른 접착제의 물성 변화에 관해 연구하였다. 항공기 운용 시 노출되는 환경 조건을 고려하여 상온 건조(Room Temperature Dry, RTD), 고온 흡습(Evaluated Temperature Wet, ETW), 저온 건조(Cold Temperature Dry, CTD) 세가지 환경에서 강도 시험을 수행하였다. 접착전단강도 시험은 ASTM D3528을 기준으로 수행하였고, 파손 영역에 대한 마이크로 구조 특성을 SEM이미지를 통해 분석하였다. 연구 결과에 따르면 RTD 환경에서의 전단강도 대비하여 ETW 환경에서 72.8% 저하되었으며, CTD 환경에서는 56.5% 증가되었다. 이는 고온 및 수분 흡습이 접착제의 기계적 특성에 큰 영향을 미치는 것을 확인했고, 저온 환경에서는 모재와 접착제 모두 취성의 증가로 인해 접착 전단 강도가 향상된 것으로 분석되었다.

• 대한치과교정학회지
• /
• 제22권2호
• /
• pp.327-343
• /
• 1992

Metal brackets and ceramic brackets were bonded to natural teeth, porcelain crowns and gold crowns After stored in artificial saliva solution for 72 hours at $37^{\circ}C$, the shear bond strengths were measured by Instron and compared with them, the bonding sites and bracket bases were examined by scanning electron microscope and light optical stereomicroscope. The results were as follows: 1. The shear bond strengths of the group which metal brackets were bonded to natural teeth and the groups which ceramic brackets were bonded to natural teeth and porcelain crowns were comparable to each other, the shear bond strength of the group which metal brackets were bonded to gold crowns was significantly low. 2. The bond failed predominantly at the bracket base/adhesive interface with the bulk of adhesive remaining on enamel in the group which metal brackets were bonded to natural teeth. 3. The bond failed consistently at the crown/adhesive interface with all of adhesive remaining on the bracket babes in the group which metal brackets were bonded to gold crowns. 4. The bond failed at the enamel or crown/adhesive interface with the bulk of adhesive remaining on the bracket bases in the groups which cramic brackets were bonded to natural teeth and porcelain crowns. 5. The shear bond strengths of the groups which ceramic brackets were bonded to porcelain crowns were not affected by etching time.