• Journal of the Korean Wood Science and Technology
• /
• v.52 no.4
• /
• pp.301-318
• /
• 2024

Contrary to other materials like metals, glass, etc., wood continuously interacts with the environment, increasing and decreasing its moisture content according to the humidity of the air and changing its dimensions by swelling or shrinking. Water diffusion through laminated solid wood is crucial in wood bonding processes. The adhesive layer might block the diffusion if the water vapor diffusion is perpendicular to the bond line. As a result of this blockage, different proportions of deformation appear on the two sides of the bond line, which causes stresses in the bonded assembly. The question arises of how long the bonded structure will keep its integrity due to moisture diffusion blockage, inevitable tensions appearing in the glue line, and how these stresses could be avoided. With cross laminated timber (CLT) solid wood panel production, this question gains new importance. Despite the relevance, only a limited number of publications are available. Comprehensive research would also be necessary considering both the molecular structure and diffusion properties of the adhesive adjusted to the wood species (covering possible substituting wood species, too). Overall, this review serves as a resource for enhancing our understanding of water vapor diffusion through wood adhesive layers and provides insights that have implications for reducing stresses in bonded wood assemblies and the performance of the bonded group over time. Furthermore, identifying knowledge gaps is necessary to establish the basis for investigating the diffusion property of CLT panels.

• Restorative Dentistry and Endodontics
• /
• v.40 no.3
• /
• pp.202-208
• /
• 2015

Objectives: This study determined the effect of the air-stream application time and the bonding technique on the dentin bond strength of adhesives with different solvents. Furthermore, the content and volatilization rate of the solvents contained in the adhesives were also evaluated. Materials and Methods:Three adhesive systems with different solvents (Stae, SDI, acetone; XP Bond, Dentsply De Trey, butanol; Ambar, FGM, ethanol) were evaluated. The concentrations and evaporation rates of each adhesive were measured using an analytical balance. After acid-etching and rinsing, medium occlusal dentin surfaces of human molars were kept moist (conventional) or were treated with 10% sodium hypochlorite for deproteinization. After applying adhesives over the dentin, slight air-stream was applied for 10, 30 or 60 sec. Composite cylinders were built up and submitted to shear testing. The data were submitted to ANOVA and Tukey's test (${\alpha}=0.05$). Results: Stae showed the highest solvent content and Ambar the lowest. Acetone presented the highest evaporation rate, followed by butanol. Shear bond strengths were significantly affected only by the factors of 'adhesive' and 'bonding technique' (p < 0.05), while the factor 'duration of air-stream' was not significant. Deproteinization of dentin increased the bond strength (p < 0.05). Stae showed the lowest bond strength values (p < 0.05), while no significant difference was observed between XP Bond and Ambar. Conclusions: Despite the differences in content and evaporation rate of the solvents, the duration of air-stream application did not affect the bond strength to dentin irrespective of the bonding technique.

• Preventive Nutrition and Food Science
• /
• v.5 no.3
• /
• pp.148-152
• /
• 2000

Mussel adhesive protein (MAP) was extracted from Korean Mytilus edulis and then partially purified using Sephacryl S-300 gel permeation chromatography and reversed-phase high performance liquid chromatography. As an indicator of adhesiveness, is 3,4-dihydroxyphenylalanine (DOPA) content was determined. Its DOPA/protein ratio of 0.19 was higher than those of other reports, indicating a good adhesive. The partially purified MAP was confirmed by acid-urea polyacrylamide gel electrophoresis using cetylpiridinium bromide as a cationic detergent. Sea mussel hydrolysates were prepared using three commercial proteases to provide value-added functional materials and their angiotensin converting enzyme (ACE) inhibitory activities were determined. Among hydrolysates of sea mussel, Protamex was the best and further purification would improved ACE inhibitory activity.

• Journal of the Korean Applied Science and Technology
• /
• v.18 no.4
• /
• pp.316-324
• /
• 2001

To prepare an acrylic type pressure-sensitive adhesive, quarternary polymers were synthesized from butyl acrylate (BA), 2-ethyl hexyl acrylate (2-EHA), methyl methacrylate (MMA), and 2-hydroxy ethyl methacrylate (2-HEMA). The quarternary polymers were identified by FT-IR and Molecular weight was measured by Gel Pearmeation Chromatography. Also, viscosity, solid content and peel strength were examined. The peel strength was 160 $g_{f}/25$ mm when the volume ratio of feed monomer to solvent was 1.3:1, and the ratio was relevant to commercial usage. The pot life of adhesive was 30 sec at the 50 m/min of heat treatment rate at, and it indicated that the minimum drying time was 30 sec. In weathering resistance test, peel strength of $160{\sim}180$ $g_{f}/25$ mm after 1000 h, with no residual remains on the adhesive surface.

• Journal of Adhesion and Interface
• /
• v.18 no.3
• /
• pp.134-140
• /
• 2017

In this study, we made UV cured acrylic pressure sensitive adhesive containing silicone-urethane-acrylate (SUA) oligomer for a coating on protective film and investigated the effect of SUA oligomer content and UV-dose on adhesion properties. The results illustrated that peel strength decreases with increasing oligomer content and UV-dose, while holding power increases. The gel fractions sharply increased after UV irradiation and then remain constant with prolonged UV exposure. From peel-off test, sample S70 (70% oligomer content) shows the best peelability and removability without remaining any mark or adhesive material on the test substrate than S50 (50% oligomer content) and S60 (60% oligomer content). Sample S70 also showed a surface energy lower than $26mJ/m^2$ and a transmittance higher than 95% at UV-dose 1857 and $2270mJ/cm^2$ which met the required properties for protective film application.

• Journal of the Korea Institute of Building Construction
• /
• v.8 no.4
• /
• pp.105-114
• /
• 2008

This study investigates the saturation level of surface dryness, quantity of adhesive mortar, and the alien substance content of recycled aggregates for concrete to develop an adequate quality testing method for understanding the properties of recycled aggregates, which differ greatly from preexisting aggregates. For tests that measure the saturation level of surface dryness, where detail methods are applied differently according to the tester, various testing methods from across world were compared and analyzed. This study revealed that when measuring the saturation level of surface dryness of a certain sample, aggregates must be supplemented immediately whenever the height of the sample becomes lower than the measuring mold, and allowing the tamper to free fall on the sample will provide the most accurate results. When measuring the quantity of adhesive mortar of recycled aggregates for concrete, an acid solution was used, and since the quantity of adhesive mortar increases as the particle sizes gets smaller, the sample for testing should represent the entire granularity. Sulfuric acid solution is adequate for immersion, and the concentration should be 20% for best results. According to the alien substance content measurement, which was examined by the naked eye, the error range caused by the difference in particle size was neglectable, and therefore the sample should be $2.5{\sim}5.0mm$ in size concerning the accuracy and measuring time. Also, for coarse recycled aggregates, the sample should amount to 1kg for measuring alien substance content by the naked eye, which proves that assortment by the naked eye is the most adequate method for measuring the alien substance content of a recycled aggregate.

• Journal of Korea Foresty Energy
• /
• v.24 no.1
• /
• pp.33-38
• /
• 2005

To find a new use of wood tar which is obtained from the manufacturing process of wood charcoal, a resol type of phenol adhesive using wood tar was made and some adhesion tests on plywood were examined. Phenol adhesive synthesized with pine tar was almost same as an original phenol adhesive in physical properties such as solid content and viscosity and tensile-shear adhesive strength of plywood made of phenol adhesive synthesized with pine tar was not much lower than the original one in non-waterproof and waterproof tests. Phenol adhesive synthesized with oak tar, however, was different from original phenol adhesive in physical properties. Adhesive strength of plywood made of oak tar was $50\%$ lower than the original one on waterproof tests. The amount of emitted formaldehyde increased as the amount of wood tar increased.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.4
• /
• pp.329-335
• /
• 2018

The objective of this study is to develop a mortar mixture with high workability and adhesive strength for section jacketing in seismic strengthening technology of existing concrete structures. To achieve targeted requirements of the mortars (initial flow exceeding 200 mm, compressive strength of 30MPa, and adhesive strength exceeding 1MPa), step-by-step tests were conducted under the variation of the following mixture parameters: water-to-binder ratio, sand-to-binder ratio, polymer-to-binder ratio, dosage of viscosity agent, and content of ultra-rapid-hardening cement. The adhesive strength of the mortars was also estimated with respect to the various surface treatment states of existing concrete. Based on the test results, the mortar mixture with the polymer-to-binder ratio of 10% and the content of ultra-rapid-hardening cement of 5% can be recommended for the section jacketing materials. The recommended mortar mixture satisfied the targeted requirements as follows: initial flow of 220 mm, high-early strength gain, 28-day compressive strength of 35MPa, and adhesive strength exceeding 1.2MPa.

• Journal of Adhesion and Interface
• /
• v.23 no.4
• /
• pp.108-115
• /
• 2022

In this study, we synthesized poly(itaconic acid-co-acrylamide) (IAcAAM) used as a novel polymer adhesion promoter to improve the adhesion strength of surface-treated Cu lead frames and epoxy composites. IAcAAM comprising itaconic acid, acrylamide was prepared through radical aqueous polymerization. The chemical structure and properties of IAcAAM was analyzed by FT-IR, ¹H-NMR, GPC, and DSC. The surface of the copper lead frame was treated with high temperature, alkali, and UV ozone to reduce the water contact angle and increase the surface energy. The adhesive strength of Cu lead frame and epoxy composite increased with the decrease of contact angle. The adhesive strength of Cu lead frame/epoxy composite increased with the addition of IAcAAM in epoxy composite. As silica content increased, the adhesive strength of Cu lead frame and epoxy composite tended to slightly decrease.

• The Korean Fashion and Textile Research Journal
• /
• v.9 no.1
• /
• pp.96-102
• /
• 2007

Antibacterial finishing of nylon 66 fabrics was carried out with sericite and medilite which are a cheap price antibacterial agents and had excellent antibacterial effects. The particle size of sericite and medilite was 15 ${\mu}m$ and 30 ${\mu}m$. The antibacterial and deodorant ratio, tensile and tear strength, peel strength were examined to investigate the change of physical properties and antibacterial effect. The results are as follows. 1. Peel strength is increased with increasing adhesive content, and satisfied standard value of peel strength when adhesive content is 20 $g/m^2$. Also peel strength was decreased with increasing antibacterial agent content and particle size in the adhesives. 2. Tensile and tear strength were not related with antibacterial agent content in the adhesives. 3. Laundering nylon 66 fabric treated with antibacterial agent, the optimum content satisfying Korean Standard(KS) is 8%. The antibacterial and deodorant ratio were not affected by several types of adhesives.