• Journal of Welding and Joining
• /
• 제13권2호
• /
• pp.106-114
• /
• 1995

The characteristics of adhesive bonded joint of steels for automobile were investigated. Shear and tear strength were tested and analyzed for the joints of cold rolled steel sheets bonded with three kinds of epoxy and urethane based adhesive. The results showed that the tensile shear strength and the tear strength of adhesive joint were affected by the shape of adhesive joint such as the length and width of adhesive joint. The thickness of adhesive layer was very important factor affecting the bonding strength. The shear strength increased with decrease of the thickness of adhesive layer, while the tear strength decreased as the thickness of adhesive layer decreased. In comparison with the strength of spot welded joint, the shear strength of adhesive Joint was higher than that of spot welded joint, but the tear strength of adhesive Joint was lower than that of spot welded joint.

• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.249-254
• /
• 2002

Adhesive contact characteristics of torus-shaped bumps were analyzed using the finite element technique considering the adhesive force. Analyses focused on the effect of rim and bump radii on the adhesive contact behavior such as the jump-to-contact behavior, adhesion hysteresis, pull-off forces, contact region and pressure, and surface and subsurface stresses. Analysis results in the absence of adhesive force were also included to examine the effect of adhesive force. The applicability of torus-shaped bumps to the MEMS structure for reduction of friction is discussed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.553-556
• /
• 2003

This study is analyzed about the factor of adhesive strength characteristics, curing time, asphalt application, test temperature which are liquid waterproofing membrane of rubber-asphalt and chloroprene-rubber type for concrete bridge deck. According to the results, curing time is shorter, adhesive strength is less in chloroprene-rubber type. And also chloroprene-rubber and rubber-asphalt type are showed high adhesive strength in low temperature.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.196-201
• /
• 2004

Adhesive joints have been widely used for fastening thin adherends because they can distribute the load over a larger area than mechanical joints, require no hole, add very little weight to the structure and have superior fatigue resistance. However, the fatigue characteristics of adhesive joints are much affected by applied pressure during curing operation because actual curing temperature is changed by applied pressure and the adhesion characteristics of adhesives are very sensitive to manufacturing conditions. In this study, cure monitoring and torsional fatigue tests of adhesive joints with an epoxy adhesive were performed in order to investigate the effects of the applied pressure during curing operation. From the experiments, it was found that the actual curing temperature increased as the applied pressure increased, which increased residual thermal stress in the adhesive layer. Therefore, the fatigue life decreased as the applied pressure increased because the mean stress during fatigue tests increased due to the residual thermal stress.

• 한국동물학회지
• /
• 제39권2호
• /
• pp.198-206
• /
• 1996

Adhesive membranes in the oocvtes of four loach fishes of Korea were investigated by light and electron microscopes to clarify the structural characteristics among the species. In the vitellosenic stage the adhesive membranes of oocvtes could be classified into two forms as follows: 1) fence-shaped form of Nemacheilus yoni and 2) non-adhesive membranous form of Misgurnus anguillicoudotus, M. Mizolepis, and Lefuo costuto. The adhesive membranes of oocvtes in the loach fishes showed a species specificity with reference to their habitats and spawning properties.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.179-184
• /
• 2002

Adhesive contact characteristics of torus-shaped bumps, which are commonly used to reduce friction and stiction in hard disks, are analyzed to examine the applicability to the MEMS structure. The analysis is conducted with the finite element technique considering the adhesive force. Torus-shaped bumps of various rim and bump radii are analyzed. The jump-to-contact behavior, adhesion hysterisis, pull-off forces, contact region and pressure, and surface and subsurface stresses are presented and discussed. Analysis results in the absence of adhesive force are also presented to identify the effect of adhesive force.

• 한국산학기술학회논문지
• /
• 제16권8호
• /
• pp.5721-5727
• /
• 2015

페인트는 외부로부터 본체가 손상되는 것을 막아주며, 오랫동안 색깔과 마무리 상태를 유지해 준다. 유기용제와 물이 페인트의 용제로 사용되고 있으며, 유기용제는 VOCs의 인위적인 공급원으로 알려져 있다. 이러한 이유로 자동차 내장부품에서 유기용재 페인트의 사용은 줄어들고 있으며, 외장 부품에서는 계속 사용하고 있다. 수성페인트의 접착력은 유성페인트에 비하여 작아, 페인트가 기제로부터 박리되고 있어, 품질문제를 일으킨다. 본 연구에서는 수성페인트와 실린 혼합물의 접착 특성에 대하여 연구하였다. 수성페인트의 접착력을 향상시키기 위하여 접착제와 혼합이 필요하다. 접착력은 UTM을 이용하여 ASTM D1002 방법으로 측정하였고, 박리현상은 ASTM D1002를 사용하여 측정하였다. 수성페인트와 실란접착제의 최적 혼합조건은 $25^{\circ}C$, 500rpm, 20분 이었으며. 실란접착제 농도는 5wt% 이었다

• Restorative Dentistry and Endodontics
• /
• 제46권2호
• /
• pp.30.1-30.13
• /
• 2021

Objectives: This study was conducted to compare the microleakage and characteristics of the resin-tooth tissue interface between self-etch and etch-and-rinse adhesive systems after 48 hours and 3 months. Materials and Methods: 40 extracted premolar teeth were randomly divided into 2 groups: 1-step self-etch adhesive system - Optibond^TM All-In-One, and 2-step etch-and-rinse adhesive system - Adper^TM Single Bond 2. Both groups were subjected to 500 thermocycles (5℃-55℃) before scanning electron microscope (SEM) analysis or microleakage trial at 48-hour and 3-month time periods. Results: SEM images showed the hybrid layer thickness, diameter, and length of resin tags of the self-etch adhesive (0.42 ± 0.14 ㎛; 1.49 ± 0.45 ㎛; 16.35 ± 14.26 ㎛) were smaller than those of the etch-and-rinse adhesive (4.39 ± 1.52 ㎛; 3.49 ± 1 ㎛; 52.81 ± 35.81 ㎛). In dentin, the microleakage scores of the 2 adhesives were not different in both time periods (48 hours/3 months). However, the microleakage score of etch-and-rinse adhesive increased significantly after 3 months (0.8 ± 0.63 and 1.9 ± 0.88, p < 0.05). Conclusions: The self-etch adhesive exhibited better long-term sealing ability in dentin when compared to that of the etch-and-rinse adhesive. The greater hybrid layer thickness and dimensions of resin tags did not guarantee reliable, long-lasting sealing in the bonding area.

• Journal of the Korean Wood Science and Technology
• /
• 제16권3호
• /
• pp.5-16
• /
• 1988

This experiment was executed to investigate the effect of activation of veneer surface by oxidizing agents, hydrogen peroxide and nitric acid, on bonding characteristics of Malas(Homalium foetidum Benth) plywood, in which the effects of these oxidizing agents amount, pretreatment time, and pressing time and temperatue on shear strength of the plywood were examined and discussed. In this research the activation of veneer surface by oxidants was effective in raising shear strength but the difference in shear strength was not observed between hydrogen peroxide and nitric acid treatment. Hydrogen peroxide treatment, however, seemed to be more profitable to industrial application because of its lower concentration and easier handling than nitric acid. The bonding method by lignin-phenol adhesive through surface activation revealed inferior shear strength to phenol- and urea-formaldehyde adhesive but superior water resistance to urea-formaldehyde adhesive and this bonding method, in addition, have the advantage of lower cost compared with phenol-formaldehyde adhesive, Therefore, this bonding method by lignin-phenol adhesive through surface activation seemed to economical in manufacturing of water-resistant wood panel materials in future.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제3권3호
• /
• pp.122-131
• /
• 2003

In this study, some characteristics of conductive and non-conductive adhesive inter-connections are derived, based on data from literature and own projects. Assembly of flip chip on flex is taken as a carrier. Potential failure mechanisms of adhesive interconnections reported in literature are reviewed. Some methods that can be used to evaluate the quality of adhesive interconnections and to evaluate their aging behavior are given. Possible finite element simulation approaches are introduced and the required critical materials properties are summarized. Response to temperature and moisture, resistance to reflow soldering and resistance to rapid change in temperature and humidity are elaborated. The effect of post cure during accelerated testing is discussed. This study shows that only a combined approach using finite element simulations, and use of appropriate experimental evaluation methods can result in revealing, understanding and quantifying the complex degradation mechanisms of adhesive interconnections during aging.