• Korean Chemical Engineering Research
• /
• v.45 no.1
• /
• pp.12-16
• /
• 2007

Temperature control of an autothermal methanol reforming reactor which uses the copper-zinc oxide catalyst was studied. Temperature at 1cm below the hot-spot point in the reactor was used for the controlled variable, and the air flow rate was used for the manipulated variable. A first order plus time delay model was identified and controller parameters were obtained by applying the IMC-PI tuning rule to the identified model. With this controller, we could control the reforming reactor temperature within ${\pm}5^{\circ}C$ over 100 hours. Change of the hot-spot point due to the catalyst degradation was investigated and it could be used to design an adaptive controller.

• 전자공학회논문지 IE
• /
• v.45 no.4
• /
• pp.60-67
• /
• 2008

Skin color is a very important information for an automatic face recognition. In this paper, we proposed a skin region extraction method using color information and skin color model. We use the adaptive lighting compensation technique for improved performance of skin region extraction. Also, using an preprocessing filter, normally large areas of easily distinct non skin pixels, are eliminated from further processing. And we use the modified ST color space, where undesired effects are reduced and the skin color distribution fits better than others color space. Experimental results show that the proposed method has better performance than the conventional methods, and reduces processing time by $35{\sim}40%$ on average.

• Journal of Korea Water Resources Association
• /
• v.36 no.4
• /
• pp.705-713
• /
• 2003

To investigate the run-up heights of nearshore tsunamis in the vicinity of a circular island, a numerical model has been developed based on quadtree grids. The governing equations of the model are the nonlinear shallow-water equations. The governing equations are discretized explicitly by using a finite difference leap-frog scheme on adaptive hierarchical quadtree grids. The quadtree grids are generated around a circular island where refined with rectangular or circular domain. Obtained numerical results have been verified by comparing to available laboratory measurements. A good agreement has been achieved.

• Journal of information and communication convergence engineering
• /
• v.10 no.3
• /
• pp.315-320
• /
• 2012

In H.264/AVC, the first frame of a group of pictures (GOP) is encoded in intra mode which generates a large number of bits. The number of bits for the I-frame affects the qualities of the following frames of a GOP since they are encoded using the bits remaining among the bits allocated to the GOP. In addition, the first frame is used for the inter mode encoding of the following frames. Thus, the initial quantization parameter (QP) affects the following frames as well as the first frame. In this paper, an adaptive peak signal to noise ratio (PSNR)-based initial QP determination algorithm is presented. In the proposed algorithm, a novel linear model is established based on the observation of the relation between the initial QPs and PSNRs of frames. Using the linear model and PSNR results of the encoded GOPs, the proposed algorithm accurately estimates the optimal initial QP which maximizes the PSNR of the current GOP. It is shown by experimental results that the proposed algorithm predicts the optimal initial QP accurately and thus achieves better PSNR performance than that of the existing algorithm.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 1999.06a
• /
• pp.83-88
• /
• 1999

In this paper, a novel gray-scale lossless image coder combining context-based minimum mean squared error (MMSE) prediction and entropy coding is proposed. To obtain context of prediction, this paper first defines directional difference according to sharpness of edge and gradients of localities of image data. Classification of 4 directional differences forms“geometry context”model which characterizes two-dimensional general image behaviors such as directional edge region, smooth region or texture. Based on this context model, adaptive DPCM prediction coefficients are calculated in MMSE sense and the prediction is performed. The MMSE method on context-by-context basis is more in accord with minimum entropy condition, which is one of the major objectives of the predictive coding. In entropy coding stage, context modeling method also gives useful performance. To reduce the statistical redundancy of the residual image, many contexts are preset to take full advantage of conditional probability in entropy coding and merged into small number of context in efficient way for complexity reduction. The proposed lossless coding scheme slightly outperforms the CALIC, which is the state-of-the-art, in compression ratio.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.430-433
• /
• 2001

When the vector control, which does not need a speed signal from a mechanical speed sensor, it is possible to reduce the cost of the control equipment and to improve the control performance in many industrial application. This paper describes a rotor speed identification method of induction motor based on the theory of flux model reference adaptive system. The estimator execute the rotor speed identification so that the vector control of the induction motor may be achieved. The improved auxiliary variable of the two model are introduced In perform accurate rotor speed estimation. The control system is composed of the PI controller for speed control and current controller using space voltage vector PWM technique. High speed calculation and processing for vector control is carried out by TMS320C31 digital signal processor. Validity of the proposed control method is verified through simulation and experimental result.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.161-164
• /
• 2001

This paper presents a digital speed sensorless control system for Reluctance Synchronous Motor (RSM) drives with direct torque control (DTC). The system consist of stator flux observer, rotor speed estimator, torque estimator two hysteresis band controllers, an optimal switching look-up table. IGBT voltage source inverter, and TMS320C31DSP controller by using fully integrated control software. The stator flux observer is based on the combined voltage and current model with stator flux feedback adaptive control that inputs are current and voltage sensing of motor terminal with estimated rotor angle for wide speed range. The rotor speed is estimated by the observed stator flux-linkage space vector. The estimated rotor speed can be determinated by differentiation of the rotor position used only in the current model part of the flux observer for a low speed operating area. In order to prove the suggested speed sensorless control algorithm. There are some simulation and testing at actual experimental system. The developed digitally high- performance speed sensorless control system are shown a good speed control response characteristic results and high Performance features using 1.0Kw RSM.

• Structural Engineering and Mechanics
• /
• v.73 no.1
• /
• pp.65-73
• /
• 2020

The present work describes a new time marching procedure for structural dynamics analyses. In this novel technique, time integration parameters are automatically evaluated according to the properties of the model. Such parameters are locally defined, allowing the user to input a numerical dissipation property for each element, which defines the amount of numerical dissipation to be introduced. Since the integration parameters are locally defined as a function of the structural element itself, the time marching technique adapts according to the model, providing enhanced accuracy. The new methodology is based on displacement-velocity relations and no computation of accelerations is required. Furthermore, the method is second order accurate, it has guaranteed stability, it is truly self-starting and it allows highly controllable algorithm dissipation in the higher modes. Numerical results are presented and compared to those provided by the Newmark and the Bathe methods, illustrating the good performance of the new time marching procedure.

• Wind and Structures
• /
• v.17 no.4
• /
• pp.361-377
• /
• 2013

Wall functions have been widely used in computational fluid dynamics (CFD) simulations and can save significant computational costs compared to other near-wall flow treatment strategies. However, most of the existing wall functions were based on the asymptotic characteristics of near-wall flow quantities, which are inapplicable in complex and non-equilibrium flows. A modified wall function is thus derived in this study based on flow over a plate at zero-pressure gradient, instead of on the basis of asymptotic formulations. Turbulent kinetic energy generation ($G_P$), dissipation rate (${\varepsilon}$) and shear stress (${\tau}_{\omega}$) are composed together as the near-wall expressions. Performances of the modified wall function combined with the nonlinear realizable k-${\varepsilon}$ turbulence model are investigated in homogeneous equilibrium atmosphere boundary layer (ABL) and flow around a 6 m cube. The computational results and associated comparisons to available full-scale measurements show a clear improvement over the standard wall function, especially in reproducing the boundary layer flow. It is demonstrated through the two case studies that the modified wall function is indeed adaptive and can yield accurate prediction results, in spite of its simplicity.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.9
• /
• pp.207-214
• /
• 2019

Natural ventilation through openings such as windows in school buildings is an efficient resource for natural cooling during the intermediate season of the year. Because the natural ventilation uses the wind outside the building, the amount of ventilation will depend not only on the wind speed and wind direction but also on the window layout and open window ratio. Therefore, in this study, the natural ventilation plans of school classroom windows are divided into 4 types and 8 cases as shown in Table 1. The characteristics of cooling effect by natural ventilation are simulated by applying Energyplus's Airflow Network Model and the comfort of the occupants is evaluated by the number of hours included in the 80% acceptability range of the ASHRAE Standard 55-2010 adaptive comfort model for the weekdays (Monday-Friday) and the class hours (08: 00-19: 00). Based on the analysis results of the above, this study presents basic data related to classroom cooling plan using intermediate season natural ventilation.