• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.735-738
• /
• 2005

Electro-Active Paper (EAPap) is attractive as an EAP actuator material due to its merits in terms of lightweight, dry condition, large displacement output, low actuation voltage and low power consumption. This paper presents the performance of EAPap actuators with thickness variation. The EAPap is made with cellulose paper, and is shown to bend in response to an external electric field. Up to the present, we have tested displacement, current and force of EAPap with 20 $\mu$m thickness. The thickness of EAPap is important factor that affects the performance of the actuator. Therefere, three different thickness of EAPap, 20, 30, and 40 $\mu$m are investigated that inference the tip displacement, blocked force, the resonance and the actuator efficiency. There is an optimum thickness of EAPap, which is resulted from the stiffness and the mass. The performance of EAPap with thickness is discussed.

• Polymer(Korea)
• /
• v.33 no.4
• /
• pp.377-383
• /
• 2009

Ionic polymer-metal composite (IPMC) actuator generates bending actuation via ion/water flux to the cathode side under an electric field. Polyelectrolytes in IPMC should possess high water-retention capability, proton conductivity, and Young's modulus. In this study. for endowing IPMCs with these properties, Nafion-alumina composite membranes containing $\alpha$- or $\gamma$-aluminas of $4{\sim}8$ wt% were prepared. Mechanical moduli of Nafion-alumina composite membranes were $7{\sim}3$ MPa higher than that of Nafion, with the slight decrease in proton conductivity. At DC 3 V. the actuation performance of the Nafion-$\alpha$-alumina (8 wt%)-IPMC was superior to that of the typical Nafion-IPMC. exhibiting 2.7 times the displacement with an enhanced blocking force. The enhanced actuation performance with the Nafion-$\alpha$-alumina composite membranes was attributed to the higher proton conductivity, the elevated ion/water flux, and the lower interfacial electric resistance of platinum electrodes and membrane, compared with those containing $\gamma$-alumina.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.7
• /
• pp.899-903
• /
• 2013

A self-bearing is an electric machine that achieves both rotational actuation and magnetic levitation using a single magnetic structure. To be able to stably levitate the rotor in a self-bearing, one needs to have an inverse of the force-current model. However, the force-current model in a self-bearing motor is typically not square. Furthermore, the elements of the matrix vary with respect to the rotational angle, resulting in singularities of the pseudo-inverse at various angles. In this paper, we propose a new force-current model that eliminates the singularities by adding a constraint in coil currents. This constraint eliminates the flux density in the stator core so that the saturation problem in the previous study is avoided. By implementing this force-current model, we are able to implement a levitation controller for a toroidally-wound self-bearing BLDC motor. The model inversion and levitation are validated experimentally.

• Journal of Institute of Convergence Technology
• /
• v.3 no.2
• /
• pp.11-15
• /
• 2013

These days, the quality of goods is required to improve in the process of manufacturing the semiconductor through the short working hours and clean transportation. The non-contact transport device using magnetic levitation can be a solution in the manufacturing process. The non-contact transport device, using electromagnetic actuation, is the system that can actually transport them by only using attraction force from the electromagnetic source without authentic contact. Moreover, the system using electromagnetic force has a substantial number of benefits ranging from unrestricted design to unlimited expansion. Especially, the price is competitive. The non-contact transport device, using electromagnetic force, has another merits in controlling by giving the same amount of attraction force to ferromagnetic body. By controlling the currents given to coil, the operator is able to decide the direction of the transportation. In order to design the optimal system, we implemented five different things such as the presence of the links below the electromagnetic, the electromagnet changes due to coupling method, the change according to the thickness of the links below electromagnet, due to changes in between electromagnetic distance direction, and the size of the current. Through simulations and the optimum design, it seems to control easily and figure out the exact size of power. It might definitely be the non-contact transport that can sharply reduce tiny scratches and particles in the process of manufacturing the semiconductor.

• Journal of Advanced Navigation Technology
• /
• v.5 no.1
• /
• pp.85-96
• /
• 2001

Recent development of a smart structures module and its successful integration with a multidisciplinary design optimization software $ASTROS^*$ and an Aeroservoelasticity module is presented. A modeled F-16 wing using piezoelectric actuators is used as an example to demonstrate the integrated software capability to design a flutter suppression system. For an active control design, neural network based controller is used for this study. A smart structures module is developed by modifying the existing thermal loads module in $ASTROS^*$ in order to include the effects of the induced strain due to piezoelectric actuation. The control surface/piezoelectric equivalence model principle is developed, which ensures the interchangeability between the control surface force input and the piezoelectric force input to the Aeroservoelasticity modules in $ASTROS^*$. The results show that the developed controller can increase the flutter speed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.2
• /
• pp.171-177
• /
• 2010

This paper presents the development of a new 6-DOF parallel-kinematic motion simulator. The moving platform is connected to the fixed base by six P-S-U (Prismatic-Spherical-Universal) serial chains. Comparing with the well-known Gough-Stewart platform-type motion simulator, it uses commercialized linear actuators mounted at the fixed base whereas a 6-UPS manipulator uses telescopic linear ones. Therefore, the proposed motion simulator has the advantages of easier fabrication and lower inertia over a 6-UPS counterpart. Furthermore, since most forces acting along the legs are transmitted to the structure of linear actuators, smaller actuation forces are required. The inverse position and Jacobian matrix are analyzed. In order to further increase workspace, inclined arrangement of universal joints is introduced. The optimal design considering workspace and force transmission capability has been performed. The prototype motion simulator and PC-based real-time controller have been developed. Finally, position control experiment on the prototype has been performed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.10a
• /
• pp.331-336
• /
• 2012

This paper proposes a new type of high-frequency directional valve controlled by the piezostack actuator associated with displacement amplifier. As a first step, a dynamic model of directional valve which can operate at 200 Hz with a flow rate of 12 l/min is derived by considering pressure drop and flow force. As a second step, an appropriate piezostack is selected by considering actuation force as well as field-dependent displacement. Subsequently, in order to control spool displacement and flow rate a proportional-derivative (PD) controller is designed based on the $3^{rd}$-order valve system. Control performances such as sinusoidal trajectory tracking of the spool displacement in time domain are evaluated. In addition, the field-dependent flow rate is also presented to verify the required performance of the valve system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.1020-1026
• /
• 2012

This paper proposes a new type of high-frequency directional valve controlled by the piezostack actuator associated with displacement amplifier. As a first step, a dynamic model of directional valve which can operate at 200 Hz with a flow rate of 12 litter/min is derived by considering pressure drop and flow force. As a second step, an appropriate piezostack is selected by considering actuation force as well as field-dependent displacement. Subsequently, in order to control spool displacement and flow rate a proportional-derivative(PD) controller is designed based on the 3rd-order valve system. Control performances such as sinusoidal trajectory tracking of the spool displacement in time domain are evaluated. In addition, the field-dependent flow rate is also presented to verify the required performance of the valve system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.3
• /
• pp.392-400
• /
• 2019

This paper provides a fin actuation system of missile based on electromagnetic-spring mechanism to miniaturize the system and lower the cost. Compared with proportional electro-mechanical actuators, the output of Electromagnetic-Spring Actuators(EMSA) has two or three discrete states, but the mechanical configuration of EMSA is simple since it does not need power trains like gears. The simple mechanism of EMSA makes it easy to build small size, low cost, and relatively high torque actuators. However, fast response time is required to improve the dynamic performance and accuracy of missiles since bang-off-bang operation of EMSA affects the flight performance of missile. In this paper the development of EMSA including parameter optimization and mathematical modeling is described. The simulation results using Simulink and experimental test results of prototype EMSAs are presented.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.2
• /
• pp.92-97
• /
• 2016

This paper presents design and simulation of wide band RF microswitch that uses electrostatic actuation for its operation. RF MEMS devices exhibit superior high frequency performance in comparison to conventional devices. Similar techniques that are used in Very Large Scale Integration (VLSI) can be employed to design and fabricate MEMS devices and traditional batch-processing methods can be used for its manufacturing. The proposed switch presents a novel design approach to handle reliability concerns in MEMS switches like dielectric charging effect, micro welding and stiction. The shape has been optimized at actuation voltage of 14-16 V. The switch has an improved restoring force of 20.8 μN. The design of the proposed switch is very elemental and primarily composed of electrostatic actuator, a bridge membrane and coplanar waveguide which are suspended over the substrate. The simple design of the switch makes it easy for fabrication. Typical insertion and isolation of the switch at 1 GHz is -0.03 dB and -71 dB and at 85 GHz it is -0.24 dB and -29.8 dB respectively. The isolation remains more than - 20 db even after 120 GHz. To our knowledge this is the first demonstration of a metal contact switch that shows such a high and sustained isolation and performance at W-band frequencies with an excellent figure-of merit (fc=1/2.pi.Ron.Cu =1,900 GHz). This figure of merit is significantly greater than electronic switching devices. The switch would find extensive application in wideband operations and areas where reliability is a major concern.