• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.615-619
• /
• 2004

A new asymmetrical zero voltage switching (ZVS) active clamp forward converter is proposed. Since the ripple current of secondary inductor plays a key role in the ZVS operation of main power switch, the proposed converter shows an excellent ZVS performance. The synchronous rectification is employed to reduce the rectification loss. The operational principle and ZVS analysis are presented. Experimental results demonstrate that the proposed converter can achieve an excellent ZVS performance throughout all load conditions and the significant improvement in the efficiency for the 100W(5V,20A) prototype converter.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.135-138
• /
• 2009

Quality evaluation of laser welded MCFC separator panels with large active area was performed. Lap joint was applied to produce stable air-tight seam weld by employing Nd:YAG laser. Results showed that surface contamination played a key role to form weld defects at the joint interface. However, there was no evidence that weld width at the lap joint changed after the stack operation time of 2,890h. Test results also revealed that the reinforcement values which were measured on the weld line after long time operation, were stable.

• 한국세라믹학회지
• /
• 제35권1호
• /
• pp.33-40
• /
• 1998

A MgO-CaO-based coating material for ferrous melt refining is applied to the tundish operation for mol-ten steel having low carbon. The changes in the total oxygen content insoluble aluminum content and the content of inclusions in molten steel during tundish operation were measured at the pouring part strand of tundish and mold. On the basis of the experimental results the interfacial reaction occurring between the coating materials and the molten steel in tundish was discussed and compared with the theoretical con-sideration. It is concluded that interfacial reaction is not active at the strand part of tundish but is active at the pouring part because of the turbulent flow in the molten steel.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권8호
• /
• pp.551-556
• /
• 2000

A zero-voltage-switching(ZVS) programmable power supply employing the ZVS active clamp forward converter is suggested. Through the analysis on operation region of the supply, the constant power region and the maximum current limit region are clearly identified. Furthermore, the duty ratio range corresponding to the variation range of the output voltages and the control scheme at the minimum duty ration region are presented. Finally, in order to vefity the validity of the operation for the proposed power supply, experimental evaluation results obtained on an 1kW prototype power supply for the 198~242VAC input voltage range(220VAC$\pm$10%), the 0~25V output voltage range, and the 100kHz switching frequency are presented.

• Journal of Electrical Engineering and Technology
• /
• 제3권2호
• /
• pp.254-262
• /
• 2008

This paper presents an active use of doubly-fed induction-generator(DFIG)-based variable-speed wind-turbine for voltage control in power system operation. For reasonable simulation studies, a detail dynamic model of a DFIG-based wind-turbine grid-connected system is presented. For the research objective, an innovative reactive power control scheme is proposed that manipulates dynamically the reactive power from the voltage source converter(VSC) with taking into account its operating state and limits.

• 전력전자학회논문지
• /
• 제26권1호
• /
• pp.9-15
• /
• 2021

In multi-string light-emitting diode (LED) driver system, current balancing is crucial because the brightness of LED is directly related to its forward current. This paper presents a novel LED current balancing topology using current-fed Z-source converter. With the proposed structure, currents flowing through two LED strings are automatically balanced owing to the charge-balance condition on capacitors. Operation of the proposed converter is simple and the proposed converter uses only one active switch and one diode. Moreover, low-side gate driving can be used to operate the active switch. To verify the operation of the proposed LED current balancing converter, a prototype is built and tested with different numbers of LEDs.

• 전자공학회논문지SC
• /
• 제40권5호
• /
• pp.350-354
• /
• 2003

본 논문에서는 능동 클램프 스위치를 위한 별도의 구동 회로가 생략된 새로운 자기 구동 능동 클램프 포워드 컨버터를 제안하였다. 능동 클램프 스위치의 구동에는 컨버터 자체의 변압기의 보조 권선을 이용하였고, 두 스위치 구동 신호 사이의 데드 타임을 설정하기 위하여 간단한 R-C지연 회로를 추가하였다. 제안된 컨버터의 동작 원리를 제시하였고 실험 결과를 가지고 이론적인 결과를 입증하였다. 출력 100W(5V/20A)의 컨버터를 제작하였으며 입력이 50V일 때 능동 클램프 스위치의 구동에 단지 1.5T의 보조 권선의 권선수로 충분하다는 점을 보였다. 끝으로 제안된 컨버터의 측정 효율을 제시하였고 91%의 최대 효율을 달성하였다.

• 전력전자학회논문지
• /
• 제18권5호
• /
• pp.477-484
• /
• 2013

This paper proposes a novel switching method of active clamp snubber for efficiency improvement of PV module integrated converter(MIC) system. Recently, MIC solar system is researched about the efficiency and safety. PV MIC system is used active clamp method of snubber circuit for the price and reliability of the system. But active clamp snubber circuit has the disadvantage that system efficiency is decreased for switch operating time because of heat loss of resonant between snubber capacitor and leakage inductance. To solve this problem, this paper proposes a novel switching method of the active clamp. The proposed method is a technique to reduce power consumption by reducing the resonance of the snubber switch operation time and through simulations and experiments proved the validity.

• 대한전자공학회논문지SD
• /
• 제41권9호
• /
• pp.31-37
• /
• 2004

oxide 층의 위치와 두께 조절을 통하여 oxide-VCSEL이 단일모드로 동작하는 활성영역의 반경을 확장하는 방법을 Self-consistent effective-index 방법을 이용하여 제시하였다. 이렇게 활성영역이 넓어지면 고속, 고신뢰도, 고출력 동작에 유리한 단일모드 VCSEL을 만들 수 있게 된다. 고출력을 위하여 단일모드로 동작하는 활성영역을 확대하는 방법을 하면 다음과 같다. 첫째 oxide 층은 활성층에서 멀리 떨어진 곳에 위치시켜야 한다 둘째, oxide 층은 얇게 만들어야 한다. 셋째, oxide층을 node에 위치시켜야 한다. 그리고 고출력을 위하여 p-DBR 쌍의 수를 줄이는 것은 단일모드 동작조건을 변화시키지 않는다. 이 방법을 사용하면 단일모드로 동작하는 oxide-aperture 크기를 3m% 이상 키울 수 있다.

• 대한의용생체공학회:의공학회지
• /
• 제29권3호
• /
• pp.179-186
• /
• 2008

This paper presents a portable tele-assessment system designed for remote evaluation of the hypertonic elbow joint of neurologically impaired patients. A patient's upper limb was securely strapped to a portable limb-stretching device which is connected through Internet to a portable haptic device by which a clinician remotely moved the patient's elbow joint and felt the resistance from the patient. Elbow flexion angle and joint torques were measured from both master and slave devices and bilaterally fed back to their counterparts. In order to overcome problems associated with the network latency, two different tele-operation schemes were proposed depending on relative speed of tasks compared to the amount of time delay. For slow movement tasks, the bilateral tele-operation was achieved in real-time by designing control architectures after causality analysis. For fast movement tasks, we used a semi-real-time tele-operation scheme which provided the clinicians with stable and transparent feeling. The tele-assessment system was verified experimentally on patients with stroke. The devices were made portable and low cost, which makes it potentially more accessible to patients in remote areas.