• Elastomers and Composites
• /
• v.49 no.3
• /
• pp.199-203
• /
• 2014

Terpolymer syrups were photopolymerized from 2-ethylhexyl acrylate, 2-hydroxylethyl acrylate and isobornyl acrylate to prepare acrylic pressure sensitive adhesives (PSAs). After polymerization, various crosslinkers as 1,6-hexanediol diacrylate (HDDA), poly (ethylene glycol) diacrylate (PEGDA, Mn = 250, 575, and 700) were added and then UV-irradiated to prepare the semi-IPN type PSAs. Their adhesion performance and storage modulus (G') were strongly dependent on their chemical structure and molecular weight of the crosslinkers. Optical properties such as transmittance (> 92.5 %), haze (< 1.0 %) and color-difference (< 0.3) of PSAs samples were not affected by crosslinker types used in this study.

• Elastomers and Composites
• /
• v.34 no.4
• /
• pp.360-365
• /
• 1999

In this study, the blends of acrylic quaternary polymer (PEBEV) which was co- polymerized from 2-ethylhexyl acrylate (2-EHA), n-butyl acrylate (BA) and ethyl acrylate (EA), vinyl acetate (VAc), and poly(vinyl chloride-co-vinyl propionate) (PVCVP) were prepared by solution blending. Pressure sensitive adhesive (PSA) properties of PEBEV/PVCVP blends were compared with those of PEBEV/poly(vinyl chloride-co-vinyl acetate) (PVCVAc) blends. Compatibility of PEBEV/PVCVP was better than that of PEBEV/PVCVAc. Tackiness of both blend systems were similar, but holding power began to decrease at 15wt% or higher PVCVAc contents in PEBEV/PVCVAc blends. On the other hands, holding power of PEBEV/PVCVP increased as the contents of PVCVP increased. Failure modes of the blends were adhesive failure except 5wt% of PVCVP was blended.

• Elastomers and Composites
• /
• v.37 no.1
• /
• pp.31-38
• /
• 2002

Polymerization of carboxylated styrene-butadiene latex takes longer time than that of acrylic emulsion due to delocalization of radical in butadiene unit having conjugated double bond. A latex stability is the most important properties owing to use intact without separating polymer from base latex. For reducing polymerization time without decreasing any properties of latex, carbon tetra-chloride which has been used as the most popular chain transfer agent was replaced to combination of tert-dodecylmercaptane and ${\alpha}$-methylstyrene dimer. The replacement yielded reducement or 2 hr in polymerization time. In the increment step, charge amount of acrylic acid was limited to 0.3 part to restrain viscosity enhancement. Just after initial step, addition of 0.1 part acrylamide prevent polymer chain from diffusing between two region followed by giving hardness and final good adhesive force to latex particles.

• Elastomers and Composites
• /
• v.47 no.3
• /
• pp.216-222
• /
• 2012

In this study, p-acryloyloxybenzoic acid(ABA) was synthesized with p-hydroxybenzoic acid(HBA) and acryloyl chloride(AC). The synthesized ABA monomer was grafted onto ethylene-propylene-diene rubber(EPDM) in toluene using benzoyl peroxide(BPO) as an initiator. The structures of ABA and EPDM-g-ABA were characterized by FT-IR, $^1H$-NMR, and $^{13}C$-NMR spectrometer. The graft ratio of EPDM-g-ABA increased with increasing the concentration of the initiator and the monomer. Mechanical properties such as tensile strength and compression set of the EPDM-g-ABA were improved with increasing the graft ratio. The $T_g$ and initial decomposition temperature were also increased with increasing the graft ratio.

• Elastomers and Composites
• /
• v.51 no.4
• /
• pp.275-279
• /
• 2016

Additive manufacturing or 3D printing is a new manufacturing process and its application is getting growth. However, the product qualities such as mechanical strength, dimensional accuracy, and surface quality are low compared with conventional manufacturing process such as molding and machining. In this study not only mechanical characteristics of polymer sandwich panel having three dimensional core layer but also mechanical characteristics of core layer itself were analyzed. The shape of three dimensional core layer was pyramidal kagome structure. This core layer was fabricated by two different methods, injection molding with PP resin and material jetting type 3D printing with acrylic photo curable resin. The material for face sheets in the polymer sandwich panel was PP. Maximum load, stiffness, and elongation at break were examined for core layers fabricated by two different methods and also assembled polymer sandwich panels. 3D printed core showed brittle behavior, but the brittleness decreased in polymer sandwich panel containing 3D printed core. The availability of 3D printed article for the three dimensional core layer of polymer sandwich panel was verified.

• Journal of Technologic Dentistry
• /
• v.8 no.1
• /
• pp.85-90
• /
• 1986

The effect of splinting on aqbutment tooth distal movement was performed in vitro study. An acrylic resin mandibular model with missing 2nd premolars, molars and a removable partial denture framework were constructed. The roots of the canines, 1st premolars and edentulous ridges were coated with silicone rubber. A modified Ney Surveyor was used for vertical load appkication, and abutment tooth distal movement were measured with a dial gauge with four conditions of splinting methods were tested by applying unilateral vertical loadings. The results are follows; 1. The magnitude of abutment tooth distal movement on the non-load side was less 40$\sim$69% than that occurred on the load side. 2. On the load side, reducing effect of splinting on abutment tooth movement in the condition of load side double abutment(30%), non-load side double abutment(10%), double abutments of both sides(40%) was compared with single abutments of both sides. 3. On the non-load side, reducing effect of splinting on abutment tooth movement in the condition of load side double abutment(5%), non-load side double abutment(22%), double abutments of both sides(59%) was compared with single abutments of both sides. 4. The magnitude of abutment tooth distal movement in the condition of double abutments of both sides was less 40$\sim$59% than that in the condition of single abutments of both sides.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.34 no.1
• /
• pp.73-80
• /
• 2007

Compomer that release fluoride could be used on proximal caries of child effectively. But oral cavity is always wet, so saliva inhibits bonding of tooth and compomer. When the saliva exist on bonding, it can be occured microleakages. The purpose of this study was to evaluate the influence of salivary contamination on compomer restoration and degree of microleakage according to restoration methods. Dyract $AP^{(R)}$ and prime and $bond^{(R)}$ NT was applied by the manufacture s instructions. Elipar Trilight was applied for light curing. Saliva pool was made for reconstruction of oral cavity. Two premolar was embedded in acrylic resin. After class II cavity preperation, Dyract $AP^{(R)}$ was restored under several condition, the specimen was thermocycled 500 times with 30 second dwell time. 0.5% methylene blue was used for microleakage test. Micoleakage was measured by the ratio of the infiltration length to occlusal and gingival side interface. Data were analyzed statistically using Kruskal Wallis Test, Mann-Whitney Test. The Result were as follows ; 1. In occlusal side, there were no statistical differences. 2. In gingival side, there were no statistical differences in Group III ($ContactMatrix^{TM}$, Rubber dam, $Oraseal^{(R)}$), Group IV (No saliva contamination). 3. In gingival side, there were no statistical differences in Group I$(ContactMatrix^{TM})$, II($ContactMatrix^{TM}$, Rubber dam). 4. In gingival side, there were statistical differences in Group I$(ContactMatrix^{TM})$, II($ContactMatrix^{TM}$, Rubber dam).

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.5
• /
• pp.61-68
• /
• 2020

In this study, the international standard ISO TS 16774 Part 3 Test Method for Water (wash out) Resistance and KS F 4935 ｢Sealant Injection type for water leakage maintenance of adhesive flexible rubber asphalt series｣, which are standardized as a quality control method of injection type repair materials used for water leakage cracks in underground concrete structures, are currently used in Korea. As a result, considering the performance criteria of "mass change rate -0.1%" stipulated in KS F 4935, the remaining 13 types repair materials, excluding RG-2 of synthetic rubber and UG-1 of urethane, need to be reviewed for stabilization of the loss resistance due to the flow of ground water. The results of this study are determined to be available as a basic indicator for the selection of repair materials used for cracks in concrete structures. In addition, it is expected that the results of this study can be utilized as reference data that can be reflected in the improvement of the quality of repair materials that will be researched and developed later.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.83-83
• /
• 2011

나노섬유는 마이크로 섬유에 비해 $10^3$배 정도의 넓은 표면적을 가지며, 다른 섬유와 비교하여 유연성, 투습성과 같은 특성이 우수하다. 나노섬유의 제조방법은 여러 가지가 있으나, 상용화의 가능성, 적용 고분자의 다양성, 제조공정의 단순성, 다양한 제품기술에의 응용성 등을 고려하여 선택하여야 한다. 나노섬유의 제조기술은 방법에 따라 전기방사, 복합방사, 멜트블로운 공정, 에어레이드 공정, 습식 공정 등으로 나눌 수 있다. 전기방사 등 나노섬유를 대량생산하여 상용화하려는 노력을 지속적으로 하고 있으나 나노섬유의 염색가공에 관련되어 기술적 한계로 제품전개에 많은 어려움을 겪고 있다. 그리하여 본 연구에서는 나노섬유 단독으로 제품화하기에는 강도 등의 문제로 PET에 워터펀칭한 복합소재로 개발하여 900nm 이하의 나노섬유에 대한 최적의 날염조건과 현장적용 생산기술을 개발하고자 하였다. 나노섬유 복합소재에 대하여 Brown, Red, Blue, Black 색상의 안료와 Urethane, Rubber, Acrylic, Eco Binder를 사용하여 날염 실험하였으며, 최적의 조건으로 현장생산에 적용하여 생산하였다. 안료의 고착성을 높여 날염성과 염색견뢰도를 증진시키기 위하여 원적외선 열처리기를 개발하여 현장생산에 접목시켰다. 원적외선 열처리기는 벙커C유 또는 가스 등을 사용하는 텐터나 증열기와는 다르게 전기를 에너지원으로 하여 원적외선 램프를 이용한 건열시스템의 형태로 저공해 및 그린 형태의 열처리기 시스템으로, 섬유에 대한 원적외선의 조사거리, 원적외선 램프의 간격, 적용 온도, 원단이송 속도 등에 따른 최적의 원적외선 열처리기 날염조건을 설정하였다. 바인더에 따른 날염성은 우레탄계 바인더를 사용하였을 경우에 가장 선명하고 깊은 색상을 보였으며, 아크릴계 바인더의 경우가 가장 낮은 색상을 보였으며 염색견뢰도는 대체적으로 양호한 결과를 얻었다. 그리고, 최근 환경적인 추세에 맞추어 에코 바인더를 사용하여 날염한 결과 염색성과 내구성 등은 우레탄계와 아크릴계 바인더의 중간 정도의 결과를 보였다.

• Journal of Bio-Environment Control
• /
• v.18 no.3
• /
• pp.200-207
• /
• 2009

This study was conducted to analyze the variations of air temperature, relative humidity and pressure in a low pressure chamber for plant growth. The low pressure chamber was composed of an acrylic cylinder, a stainless plate, a mass flow controller, an elastomer pressure controller, a read-out-box, a vacuum pump, and sensors of air temperature, relative humidity, and pressure. The pressure leakage in the low pressure chamber was greatly affected by the material and connection method of tubes. The leakage rate in the low pressure chamber with the welding of the stainless tubes and a plate decreased by $0.21kPa{\cdot}h^{-1}$, whereas the leakage in the low pressure chamber with teflon tube and rubber O-ring was given by $1.03kPa{\cdot}h^{-1}$. Pressure in the low pressure chamber was sensitively fluctuated by the air temperature inside the chamber. An elastomer pressure controller was installed to keep the pressure in the low pressure chamber at a setting value. However, inside relative humidity at dark period increased to saturation level.. Two levels (25 and 50kPa) of pressure and two levels (500 and 1,000sccm) of mass flow rate were provided to investigate the effect of low pressure and mass flow rate on relative humidity inside the chamber. It was concluded that low setting value of pressure and high mass flow rate of mixed gas were the effective methods to control the pressure and to suppress the excessive rise of relative humidity inside the chamber.