• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.212-216
• /
• 2005

Benzotriazole which is used as a corrosion inhibitor for the zinc coated steel was intercalated into Na-MMT. X-ray diffraction experiments on intercalant/silicate composite samples demonstrated that the intercalation of intercalant leads to an increase in the spacing between silicate layers. Water soluble poly(ethylene-co-acrylic acid) (PEA) nanocomposites, to use as a coating agent, were prepared with these modified MMT. We found that mono-layered silicates were dispersed in PEA matrix and those resultants were exfoliated nanocomposites. From the result of salt spray test, we found that this coating agent prepared with water soluble poly(ethylene-co-acrylic acid) (PEA) nanocomposite provided good corrosion protection. These results were caused by decreasing the rate of oxygen permeation from silicate layers dispersed homogeneously in PEA matrix and the effect of corrosion inhibitor from benzotriazole.

• Korean Chemical Engineering Research
• /
• v.55 no.6
• /
• pp.754-761
• /
• 2017

UV-curable hydrophilic coating solutions were prepared by mixing colloidal silica dispersed in alcohol with an acrylic monomer, pentaerythritol triacrylate (PETA). Hydrophilic coating films were also prepared by spin coating the hydrophilic coating solutions on PC substrates and UV curing for 10 minutes subsequently. The effect of the amount of colloidal silica in the coating solutions, which was varied from 10 g to 50 g, was investigated on the hydrophilic properties of UV-cured coating films. The results showed that the amount of colloidal silica had a great influence on the hydrophilic properties of UV-cured coating films and the coating film prepared with 30 g of colloidal silica showed a lowest contact angle of $37^{\circ}$ and an excellent pencil hardness of H.

• Applied Chemistry for Engineering
• /
• v.24 no.2
• /
• pp.171-176
• /
• 2013

The need of volatile organic compound (VOC) free coating material has been increased to solve environmental problems such as the global warming. Nowadays, about 70~80% of coating materials used in the worldwide are a liquid type. Therefore, the development of non-solvent coating material that can minimize VOCs emissions is necessary to solve the global warming problem. In this study, acrylic monomers were added to develop non-solvent paints in order to improve disadvantages of the poor adhesion of a conventional phenolic resin caused by acidification. As a result, the blend resins of 2.818 Mpa phenol- formaldehyde resin/poly methyl methacrylate (PE/PMMA) has the best properties and performances for the adhesives.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.138-143
• /
• 2014

${\alpha},{\omega}$-Hydroxypropyl polydimethylsiloxane (HO-PDMS) was prepared by hydrosilylation of hydrogen terminated polydimethylsiloxane with allyl alcohol. Polydimethylsiloxane modified urethane with isocyanate group (PSU) was prepared from cyclic trimer of hexamethylenediisocyanate with HO-PDMS. PDMS modified urethane base resin with acrylic group (PSUA) was prepared from the urethane reaction of PSU with isocyanate group and 2-hydroxyethylmethacrylate. Their structures were characterized using FTIR and NMR. Coating materials were prepared by mixing PSUA, acrylic hardner, photo-initiator, and solvent and coated on PET film to obtain flexible and hard coating film by UV irradiation. Transparency of coating film was 89.7%, contact angle, $88^{\circ}$, and pencil hardness, 3H.

• Polymer(Korea)
• /
• v.35 no.6
• /
• pp.520-525
• /
• 2011

Superporous hydrogels (SPHs) with fast swelling and superabsorbent properties are useful materials in various biomedical fields, by improving the swelling properties of conventional hydrogels based on their unique porous structure. In this study, Eudragit polymers were used as coating materials to control the swelling properties of poly(acrylic acid-co-acrylamide) based SPHs by environmental pH. The SPHs were coated with Eudragit L100 and S100 that have different pH characteristics as enteric coating materials by a dip coating method, and their pH dependent swelling behaviors were observed in various pH environments. The swelling of SPHs was inhibited at a low pH range, but significantly enhanced above a characteristic pH of Eudragit polymers. This pH dependent swelling behavior of hydrogels could be modulated by the characteristics of the enteric coating polymers.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.191-197
• /
• 2012

Acrylic terminated polyurethane prepolymers were synthesized by capping the NCO groups of polyurethane prepolymers, prepared from isophorone diisocyanate (IPDI), polycarbonate diol (PCD) and dimethylol propionic acid (DMPA), with pentaerythritol triacrylate (PETA). Subsequently, silylated acrylic terminated prepolymers were prepared by capping the NCO groups of acrylic terminated polyurethane prepolymers with different types of silane coupling agents, glycidoxypropyl trimethoxysilane (GPTMS) or aminopropyl triethoxysilane (APS). The average particle size of pure waterborne polyurethane solution, measured by the dynamic light scattering method, was increased from 14.3 nm to 208.6 nm by adding PETA and APS. Also, the coating film of silylated acrylic terminated waterborne polyurethane showed better abrasion resistance and pencil hardness than that of pure waterborne polyurethane.

• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.187-198
• /
• 2018

Clay based coating with zwitterionic functionality is used to remove cationic and anionic dyes. Adsorbent coating was prepared by the mixing of bentonite clay, acrylic polymer (AP) and polyethylene-diamine (EPI-DMA). Characterization was performed using SEM-EDX, XRF, X-ray mapping and FTIR analyses. The adsorption capacity of ZACC was found to be increased from 59.35 to 255.99 mg/g and from 45.84 to 70.09 mg/g for BG and AR1 dyes, respectively using initial concentration (50-200 ppm). Significant adsorption capacity along with mechanical and chemical stability formulates ZACC as an excellent composite coating for treatment of anionic and cationic dyes from industrial wastewater.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.9
• /
• pp.2396-2401
• /
• 2009

This study is on development of UV-cured hard coating compounds which have more improved abrasion resistance than existing UV-cured urethane-acrylic resin, to prevent a surface of a widely used PVC tile as a constructive material from being scratched. To make a high abrasion resistant hard coating solution compared to UV-cured urethane-acrylic resin which has no abrasion resistance and been used for PVC tiles, we added powder substances of different abrasion resistant level, $Al_2O_3$(Al-160SG-3), $Al(OH)_3$(SH-8W), $SiO_2$(KS-5000), etc., to the resin, changing their contents from 10% to 30% against quantities of resin, and compounded it using Ring-Mill. After coating PVC tiles with the hard coating solution using bar-coating method that can adjust a thickness, we estimated some surface properties-abrasion resistance, pencil hardness, adhesive power, thickness of coating, and so on. As a result, a hard coating solution added 30% $Al_2O_3$ powder to the resin had the finest surface properties-the first grade in abrasion resistance, H in pencil hardness, 100% in adhesive power, and a hard coating solution which showed excellent solidity and abrasion resistance has smaller particle size, higher powder content, and thicker coating thickness.

• Proceedings of the KAIS Fall Conference
• /
• 2001.11a
• /
• pp.91-94
• /
• 2001

리튬전지의 vent cap ass'y용의 AI foil에 LDPE(low density polyethylene)만을 coating하였으나 LDPE는 vent cover인 sus와의 열접착성이 우수하지 못하기 때문에 vent 조립시 상당한 주의가 필요했다. 그러나, LDPE보다 열접착성이 우수한 EVA(ethylene vinylacetate)와 EAA(ethylene acrylic acid)의 2중 coating된 AI foil을 이용함으로 열접착성을 향상시킬 수 있었다. 이에 따라, 전해액 누액 등의 전지 불량 원인을 제거함과 동시에 vent cap ass'y의 조립시 공정 불량까지 감소시킬 수 있었다.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3316-3318
• /
• 1999

PMMA(poly-methyl methacrylate) microlens array is fabricated using transparent acrylic resin. PMMA is commonly used material for plastic lens due to its excellent visibility larger than 90% and other optical characteristics so much close to those of glass. Orthodontic resin (DENTSPLY International Inc.), commonly used in dentistry, is an transparent acrylic resin kit including MMA liquid and polymerization powder. Their mixture results in PMMA through polymerization. Using the resin PMMA layer is formed on the substrate through spin-coating. Designed pattern of lens structure is transferred to PMMA layer by RIE (Reactive Ion Etching) with oxygen plasma. Final lens shape is formed by thermal treatment that causes PMMA to reflow, The thickness of PMMA spun on the substrate is $17{\mu}m$ that is also final sag of microlens, Designed diameters of the microlenses are $200{\mu}m$, $300{\mu}m$,and $500{\mu}m$, respectively.