• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1209-1215
• /
• 2010

The effects of multi-walled carbon nanotube (MWCNT) content, carbon black (CB) content, atmospheric-pressure flame plasma (APFP) treatment, and acid treatment on the mechanical properties of elastomeric composites were investigated. For pure or filled rubbers with the given amount of CB (20 and 40 phr), the tensile strength and modulus of the elastomeric composites increase similarly with the MWCNT content. A composite with APFP-treated MWCNTs shows a hardening effect (high strength, high modulus, and high ductility) unlike the one with untreated MWCNTs. On the other hand, a composite with APFP-treated CB shows a softening effect (high strength, low modulus, and high ductility), which is unlike a composite with untreated CB. As the refluxing time increases from 1 h to 2 h and the sulfuric acid concentration increases from 60% to 90%, the tensile strength and modulus of a composite decrease. Thus, it is found that the MWCNT content, CB content, APFP treatment, sulfuric acid concentration, and refluxing time have an important effect on the mechanical properties of NBR composites.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.5
• /
• pp.95-102
• /
• 2010

In recent years, the demand for the development of high quality and cost effective materials, as well as the competition to ensure a diverse and sufficient amount of ready-mixed concrete, has been increasing rapidly. In this experiment, concretes made with different admixtures are blended with each other in different combinations and ratios, in order to identify potential problems. The first test was a slump level test, in which all of the concretes met the required numbers, as they also did in the test for air content. Plain organic acid concrete scored the highest in bleeding amount, but organic acid mix in general showed a similar outcome. In the early measurement of compressive strength, plain naphthalene concrete was the strongest. Of the blends, the 5:5 mix of organic acid and naphthalene was the strongest. In the standard measurement, the 5:5 mix of naphthalene and lignin was the strongest. Tensile strength tests revealed similar results. Length change rate proved to be greater in blended concrete than in plain concrete, and dry shrinkage rate was highest in the 7:3 ratio blends. Through SEM photo analysis, it was confirmed that the 7:3 ratio blends contained more micro-voids. In conclusion, with the exception of a specific few combinations, it was found that the blending of different types of concrete is undesirable due to the delayed coagulation time as well as the early decrease in strength.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.3
• /
• pp.87-94
• /
• 2016

In order to improve performances of submicrometer-sized Si negative electrode which shows larger volumetric change than nano-sized Si, composite binders are introduced by blending between poly(phenanthrenequinone) (PPQ) conductive polymer binder and poly(acrylic acid) (PAA) having good adhesion strength due to its carboxyl functional group. Blending between PPQ and PAA shows an effect that the adhesion strength of the Si electrode with the composite conductive binder is greatly improved after blending and this makes its better stable cycle performance. Blending ratios between PPQ and PAA in this work are 2:1, 1:1, 1:2 (by weight) and the best capacity retention at 50th cycle is observed in the electrode with the blending ratio 2:1 (named QA21). This is because that PPQ plays a role of conductive carbon among the Si particles or between Si particles and Cu current collector and PAA binds effectively the particles and the current collector. According to this synergetic effect, the internal resistance of the Si electrode with the blending ratio 2:1 is the smallest value. In addition, the Si electrode with PPQ-PAA composite binder shows the better stable cycle performance than the electrode with conventional super-P conductive carbon (20 wt.%).

• Applied Chemistry for Engineering
• /
• v.28 no.3
• /
• pp.360-368
• /
• 2017

In order to investigate the durability of high performance polymer concrete composites, polymer concrete specimens were prepared using the ortho-type unsaturated polyester resin (UPR) and iso-type UPR as a polymer binder and the calcium carbonate and silica fine powder as a filler. The durability of polymer concrete specimens was measured by hot water resistance, chemical resistance, pore analysis and SEM observation. The compressive strength of the specimen using the iso-type UPR was higher than that of using the ortho-type UPR, and the compressive strength of the specimen using the silica fine powder was higher than that of using the calcium carbonate filler. From hot water resistance results, it was found that the specimen using the iso-type UPR was superior to that of using the ortho-type UPR and the specimen using the calcium carbonate filler was superior to that of using the silica fine powder. The compressive strength reduction rate was measured after the chemical resistance test and the sodium hydroxide solution showed the highest reduction rate, followed by sulfuric acid, hydrochloric acid and calcium chloride solutions. When using the alkaline solution of sodium hydroxide, the weight reduction rate of the specimen using calcium carbonate was lower than that of using silica fine powder, while for the acidic solutions of sulfuric acid and hydrochloric acid, the weight reduction rate of the specimen using the silica fine powder was lower than that of using calcium carbonate.

• Journal of the Korea Concrete Institute
• /
• v.27 no.6
• /
• pp.641-649
• /
• 2015

The purpose of this study was to assess the durability of high-strength concrete with high volume mineral admixture (HVMAC) derived from previous studies within ternary blended concrete (TBC) and normal concrete (NC). Four durability evaluation types such as chloride penetration resistance, freezing and thawing resistance, carbonation resistance in two pre-treatment conditions, and sulfuric acid and sulfate resistance using 5% sulfuric acid ($H_2SO_4$), 10% sodium sulfate ($Na_2SO_4$), and 10% magnesium sulfate ($MgSO_4$) solution were selected and performed in this study. HVMAC showed the excellent chloride penetration resistance in any age and the freezing and thawing durability close to 100%. In addition, HVMAC affected more reduction in carbonation resistance than TBC. When the curing time was increased, to create a concrete internal organization densely improved resistance to carbonation. HVMAC also showed the most superior in sulfuric acid and sulfate resistance. As the reduction of calcium hydroxide and $C_3A$ to apply a large amount of admixture reduced the swelling and cracking of concrete, the strength reduction and mass change of concrete was found to be small indicated.

• Korean Journal of Food Science and Technology
• /
• v.17 no.5
• /
• pp.340-344
• /
• 1985

In this study, an effective method for purifying of crude agar was attempted, and at the same time, the effect of crude protein and ash contained in impurified agar on the gel strength of the agar were investigated. In order to reduce the content of protein of crude agar, the agar extract was treated with a protein precipitant such as tricholoroacetic acid(TCA) or perchloric acid(PCA), whereas washing with deionized water was applied to decrease the ash content of agar extract. Among the protein precipitants used in the experiment PCA reduced the crude proteins of crude agar most efficiently; addition of 0.01% PCA resulted in the reduction of crude protein content by 3%, and the gel strength of agar thereby increased from 220g/$cm^{2}$ to 402g/$cm^{2}$. High ash content of crude agar was removed by means of washing treatment and it decreased from 8.1% to 2.7%, leading to the gel strength of 530g/$cm^{2}4$.

• Restorative Dentistry and Endodontics
• /
• v.17 no.1
• /
• pp.104-114
• /
• 1992

The purpose of this study was to evaluate the shear bond strength of glass ionomer cement(Ketacfil, ESPE, Co.) against dentin surface which had been treated with surface conditioning agents(distilled water, 5% sodium hypochlorite solution, Ketac - conditioner, 40% polyacrylic acid). In this study, 60 human molars with sound and healthy crown portion which were previously extracted for orthodontic or periodontal problem. The dentin surfaces of these teeth were exposed with wet trimmer and polished with 150 - grit and 600 - grit silicon carbide paper and the teeth were divided into four groups(15 teeth per group) according to the following surface conditioning methods. Group I : Surface treatment with distilled water as control group. Group II : Surface conditioning with 5% sodium hypochlorite solution. Group III : Surface conditioning with Ketac conditioner. Group IV : Surface conditioning with 40% polyacrylic acid. The shear bond strengths were measured by Autograph(Shimatzu Co. Japan). The result of the evaluations were then subjected to statistical analysis using one - way analysis of variance and Duncan test and the results were as follows : 1. The shear bond strength accrding to the dentin surface conditioning conditions was highest in Ketac conditioner group, with measurements of $44.44{\pm}0.74(kg/cm^2)$ and lowest in the distilled water group, with measurements of $28.84{\pm}0.88(kg/cm^2)$. 2. Statistically significant differences were found between surface conditioning with 5% sodium hypochlorite solution group or Ketac conditioner group and distilled water group(P<0.01). 3. Also, statistically significant difference was found between surface conditioning with distilled water group and 40% polyacrylic acid group(P<0.05). 4. Overall difference in statistical significance between the groups was not found (P<0.05). 5. Fractured dentin surface treated with conditioning solutions showed cohesive fracture. 6. Distilled water group and 5% sodium hypochlorite solution group removed the smear layer less effectively. 7. Conditioning dentin with Ketac conditioner and 40% polyacrylic acid resulted in the removal of a significant amount of the smear layer without removing the tubular plugs and dissolving the peritubular dentin.

• Korean Journal of Microbiology
• /
• v.7 no.3
• /
• pp.115-124
• /
• 1969

The mash of Takjoo, Korean flour wine, is fermented through two brewing processes ; the primary brewing process to saccharify and the main one to produce ethyl alcohol. The activities of acid proteinase (pH3), weak acid proteinase (pH 6), and alkaline proteinase (Ph 80 on the processes are determined with time by the Folin phenol method as a strength of casein digestion. Hydrogen ion concentration, the content of total organic acids, protein, free amino acids and oligopeptides, which effect the activities of proteinase, are also measured. The results are briefly summarized as follows : 1. In general, the activities of acid proteinase and weak acid proteinase in the mesh of primary brewing process are stronger than those in main brewing process. 2. The activities of acid proteinase are remarkably stronger than those of weak acid proteinase in both processes. It reveals that they decrease slowly through the fermentation. Activities of alkaline proteinase are weaker than others. 3. As the raw materials are mixtured, the total amount of organic acids is equivalent to 0.150 mg/ml acetic acid in the mesh of primary brewing process and 0.02 mg/ml acetic acid in the main one. They increase gradually with time. 4. Hydrogen ion concnetration shows 3.9 in the mesh of main brewing process and 3.28 in the primary one. They increase to the maximum in 60-72 hrs., and decrease since 108 hrs. 5. The content of crude protein shows 66.90mg/ml in the mesh of main brewing process, while shows 64.29mg/ml in the mesh of primary one. they decrease slowly with time. it seems that a small content of crude protein, as a substrate, converts into amino acids and soluble nitrogen compounds by proteinase. 6. The content of free amino acids and oligopeptides shows 0.36 mg/ml in the mesh of primary brewing process and 0.24mg/ml in the main brewing process. It is evident that the reason they increase continuously through the fermentation is the effect of proteinase. 7. According to the results, the strong activities of proteinase in primary brewing process has been derived from the decrease of hydrogen ion concentration due to the production of organic acids.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.6
• /
• pp.847-853
• /
• 1999

A Pseudomonas sp. strain that is capable of utilizing dicarboxylic acids as a sole carbon source was isolated from activated sludge by using the enrichment culture technique. This organism accumulated polyhydroxyalkanoates (PHAs) with an unusual pattern of monomer units that depends on the carbon sources used. Polyhydroxybutyrate (PHB) homopolyester was synthesized from glucose or small $C_{-even}$ alkanoic acids, such as butyric acid and hexanoic acid. Accumulation of PHB homopolyester was also observed in the cells grown on $C_{-odd}$ dicarboxylic acids, such as heptanedioic acid and nonanedioic acid as the sole carbon sources. In contrast, a copolyester consisting of 6 mol% 3-hydroxybutyrate (3HB) and 94 mol% 3-hydroxyvalerate (3HV) was produced with a PHA content of as much as 36% of the cellular dry matter. This strain produced PHAs consisting both of the short-chain-length (SCL) and the medium-chain-length (MCL) 3-hydroxyacid units when heptanoic acid to undecanoic acid were fed as the sole carbon sources. Most interestingly, polyester consisting of significant amount of relevant fractions, 3HB, 3HV, and 3-hydroxyheptanoate (3HHp), was accumulated from heptanoic acid. According to solvent fractionation experiments, the polymer produced from heptanoic acid was a blend of poly(3HHp) and of a copolyester of 3HB, 3HV, and 3HHp units. The hexane soluble fractions contained only 3HHp units while the hexane-insoluble fractions contained 3HB and 3HV units with a small amount of 3HHp unit. The copolyester was an elastomer with unusual mechanical properties. The maximum elongation ratio of the copolyester was 460% with an ultimate strength of 10 MPa, which was very different from those of poly(3HB-co-3HV) copolyesters having similar compositions produced from other microorganisms.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.3
• /
• pp.319-324
• /
• 2003

Statement of problem. Adhesives in dentistry playa major role in the success of restorative treatments. In the treatment of all ceramic restoration it is needed to find the adequate bond strength between enamel and dentin. Purpose. The purpose of this study was to evaluate shear bond strength of resin cement bonded to extracted human uncut enamel, cut enamel, and dentin in vitro. Material and methods. Ten freshly extracted anterior teeth without any previous restorative treatments were chosen. The extracted teeth were embedded in PMMA cold acrylic in the shape of a cylinder, 25 mm in diameter by 25 mm in height. The bonding system used was as follow: Uni-Etch (32% phosphoric acid), One-Step adhesive, Duolink resin cement. The specimens were acid etched and rinsed with water. Two layers of One-Step adhesive were coated with a disposable brush on the uncut enamel. VIP curing light at $500mV/cm^2$ was used to cure the adhesive. For cut enamel shear bond test, the specimen used for uncut enamel was further reduced approximately $0.3{\sim}0.5mm$ using a laminate preparation diamond bur (0.3 mm in depth). The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit SiC paper and cleaned with distilled water. The bonding procedure on the cut enamel was same as uncut enamel bonding procedure. For dentin bonding test, the specimen used for cut enamel was further reduced approximately $0.5mm{\sim}1.0mm$ using a laminate preparation diamond bur (0.5 mm in depth of diamond cutting). The amount of reduction was evaluated with the silicone mold. The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit silicon carbon paper and cleaned in distilled water. The bonding procedure on the dentin was same as uncut enamel bonding procedure. All samples were mounted and secured on the Ultradent shear bond test sample holder, and Ultradent restricted shear bond testing device was used with Universal Instron machine until fracture. Analysis of variance (ANOVA) test was performed comparing the result at P<0.05. Multiple comparison (Tukey) was used to compare each groups. Result. The result showed that the mean value in shear bond strength of resin cement bonded to uncut enamel, cut enamel and dentin were 27.04 Mpa, 30.25 Mpa and 26.39 Mpa with respect. Conclusion. Within the limitation of this study, the mean value of the shear bond strength of cut enamel was higher than those of uncut enamel or dentin. However there existed no statistical differences between three different human dentition substrates due to increased adhesive characteristics.