• Journal of Technologic Dentistry
• /
• v.31 no.3
• /
• pp.9-14
• /
• 2009

This study evaluated the mechanical properties of Ti-Cu alloys with the hope of developing an alloy for dental casting with better mechanical properties than unalloyed titanium. Ti-Cu alloys with four concentrations of Cu(2,5,10wt%) were made in an argon-arc melting furnace. The microstructure and micro-Vickers hardness were determined. X-ray diffraction pattern test was performed on the polished specimens. The microstructure of 2%Cu and 5%Cu alloys are shown acicular ${\alpha}Ti$ phase formed on the surfaces of previously formed $\beta$grains. The 10%Cu alloys has essentially a eutectoid structure; this structure includes lamella of ${\alpha}Ti$ and $Ti_2Cu$ phase that transformed from ${\alpha}Ti$ at the eutectoid temperature. The micro-Vickers hardness of CP Ti specimens was significantly(p<0.05) lower than that of any of the other alloys. Among the Ti-Cu alloys, the 10%Cu alloys exhibited a significantly(p<0.05) higher hardness value. but lower than that of Ti-6%Al-4%V alloy. From these results, it was concluded that new alloys for dental castings should be designed as Ti-Cu based alloys if other properties necessary for dental castings were obtained.

• Journal of Korea Foundry Society
• /
• v.13 no.2
• /
• pp.187-193
• /
• 1993

In this study, it was examined the relationship between the microstructure, fatigue properties, mechanical properties and retained austenite volume of Mo-Ni ADI corresponding to various austempering temperatures. When the austempering temperature is increased to $370^{\circ}C$, acicular bainite structure was found to be transformed to feathery bainite structure. But at the austempering temperature of $420^{\circ}C$, the dissolved bainite lath was showned. Up to the austempering temperature of $370^{\circ}C$, the volume of retained austenite was increased. However at the austempering temperature of $420^{\circ}C$ a large amount of retained austenite was decreased. In this study, the retained austenite volume was determined by XRD(X-ray diffraction). It was observed that the optimum fatigue properties can be obtained at the condition of austempering temperature $370^{\circ}C$. Under the such conditions, fatigue limit determined as the value of 290 MPa, tensile strength 877MPa elongation 6%, hardness 285(BHN), impact values(CVN) 9.2J and retained austenite volume 30.3%, respectively.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.245-251
• /
• 2002

We prepared γ-alumina beads using the amorphous alumina, obtained by fast calcination of gibbsite, and its were immersed in aqueous solution of the mixture of 21.87% nitric acid and 28.57% acetic acid. The beads thus were hydrothermaly treated at 200$^{\circ}$C for 3h, and were investigated changes of crystal, pore characteristics, $N_2$ adsorption and desorption isotherms, mechanical strengths and thermal resistance. Acicular platelet crystals of 0.1∼0.3${\mu}$m were transformed into acicular boehmite crystals of 1∼2${\mu}$m having the same crystal structure. Through this changes, we found that reversible phase transformation due to hydrothermal reaction took placed between boehmite and ${\gamma}$-alumina. In comparison to the ${\gamma}$-alumina bead before hydrothermal treatment, $N_2$ adsorption capacity was increased from 450㎖/g to 670㎖/g, and pore volume between 100${\AA}$ and 1000${\AA}$ was increased form 0.15㎖/g to 0.77㎖g, and mechanical strength was increased form 1.4MPa to 2.2MPa. Also, it showed the remarkable thermal resistance which sustained ${\theta}$-alumina crystal structure and pores between 100${\AA}$ and 1000${\AA}$ at 1000$^{\circ}$C in 40vol% steam.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.1
• /
• pp.92-100
• /
• 2008

Experimental studies were conducted to identify the active agents for reductive dechlorination of TCE in cement/Fe(II) systems focusing on cement components such as CaO, $Fe_2O_3$, and $Al_2O_3$. A hematite that was used to simulate an $Fe_2O_3$ component in cement was found to have degradation efficiencies (k = 0.641 $day^{-1}$) equivalent to that of cement/Fe(II) systems in the presence of CaO/Fe(II), only when it contained an aluminum impurity$(Al_2O_3)$. When the effect of $Al_2O_3$ content of hematite/CaO/$Al_2O_3$/Fe(II) system was tested, the mole ratio of $Al_2O_3$ to CaO affected the rate of TCE degradation with an optimum ratio around 1 : 10 that resulted in a rate constant of 0.895 $day^{-1}$. In the SEM images of hematite/CaO/$Al_2O_3$/Fe(II) systems, acicular crystals were also found that were also observed in cement/Fe(II) systems. Thus it was suspected that these crystals were reactive reductants and that they might be goethite or ettringite that are known to have acicular structures. An EDS element map analysis revealed that these crystals were not goethite crystals. A subsequent experiment that tested reactivities of compounds formed during the ettringite synthesis showed that ettringite and minerals associated with ettringite formation are not reactive reductants. These observations conclude that a mineral containing CaO and $Al_2O_3$ with a acicular structure could be a major reactive reductant of cement/Fe(II) systems.

• Applied Chemistry for Engineering
• /
• v.17 no.6
• /
• pp.619-624
• /
• 2006

This study was performed to investigate the formation process of calcium sulfate ${\alpha}$-hemihydrate from FGD gypsum produced at thermal power plant burning bituminous coal. The experimental results showed that calcium sulfate $\alpha$-hemihydrate with a large aspect ratio was produced in the temperature range of $120^{\circ}C$ and $140^{\circ}C$ in the absence of additives through dissolution-recrystallization mechanism. It was also observed that addition of Na-succinate as a catalyst changed crystal shape from acicular to prismatic, resulting in decreased water/powder ratio down to 33%. Optimum concentration of Na-succinate was 20mM. It was confirmed that the optimum moulding pressure and moisture content of moulded body from FGD gypsum were $30kg_f/cm^2$ and between 10% and 15% respectively, which prevent moulded body from collapsing and maximize the capillary effect by given pore volume while autoclaving.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.4_1
• /
• pp.531-539
• /
• 2020

When injection mold is repeatedly used for mass production, fatigue phenomenon due to cyclic stress may occur. The surface and interior of structure might be damaged due to cyclic stress or strain. The objective of this study was to analyze failure of SCM435 high-tension bolts connecting upper and lower parts of a three-stage injection molding machine. These bolts have to undergo an accurate heat treatment to prevent the formation of chromium carbide and the action of dynamic stresses. Bolts were fractured by cyclic bending stress in the observation of ratchet marks and beach marks. Damaged specimen showed an acicular microstructure. Impurity was observed. Chromium carbide was observed near the crack origin. Both shape parameters of the Vickers hardness were similar. However, the scale parameter of the damaged specimen was about 20% smaller than that of the as-received specimen. Much degradation occurred in the damaged specimen. Bolts should undergo an accurate heat treatment to prevent the formation of chromium carbide. They must prevent the action of dynamic stresses. Bolts need accurate tightening and accuracy of heat treatment and screws need compression residual stress due to peening.

• Journal of Korea Foundry Society
• /
• v.12 no.5
• /
• pp.403-411
• /
• 1992

The growth characteristics of bainite at early stage in the fast quenched spheroidal graphite cast irons containing 0.06%Mn and 0.45%Mn during austempering process, was investigated with optical and scanning electron microscope. The following results regarding the effects of Mn and isothermal heat treatment on the morphological variation of bainitic ferrite were obtained. The morphology of bainite varies from acicular below 350$^{\circ}C$ to feather shape above 350$^{\circ}C$. The period of isothermal treatment also affects the shape of bainite at the fixed temperature. At 350$^{\circ}C$, bainite is bamboo leaf-like up to 200 secs of isothermal holding time and with further increasing time up to 300 secs, changes to a mixed structure consisting of both feather and bamboo leaf and, finally becomes all feather shape at 900 secs. The morphology of bainitic ferrite formed at early stage of 300$^{\circ}C$ isothermal treatment is similar to that of bainitic ferrite formed at 250$^{\circ}C$ or 350$^{\circ}C$ with unbranched, linear ferrite. However, bainitic ferrite divides into branches with increasing isothermal treatment, which occurs more fast at 400$^{\circ}C$ than at 350$^{\circ}C$. The difference in adding amount of Mn influences the morphology of bainitic ferrite in upper bainite. The bainitic ferrite with 0.45%Mn is observed to be more stable than that with 0.06%Mn, remaining unbranched for a longer period at the same temperature.

• Journal of Korea Foundry Society
• /
• v.30 no.5
• /
• pp.161-166
• /
• 2010

In this examination, the effect of Sr addition and holding time on microstructure of Al-10.5wt%Si-2wt%Cu secondary die-casting alloy was investigated. Degree of undercooling was improved with increasing the Sr content in this alloy. Up to 0.02wt%Sr addition, acicular and lamellar eutectic structure was observed in the microstructure. Meanwhile, the eutectic Si was modified toward the fine fibrous form by increasing Sr content with more than 0.03wt% and holding time of the melt. The well- modified alloys showed decreased eutectic silicon size from 3.25 ${\mu}m$ to less than 0.8 ${\mu}m$. From these results, the optimal strontium content and holding time were identified on the Al-10.5wt%Si-2wt%Cu secondary die-casting alloy.

• Nano
• /
• v.13 no.11
• /
• pp.1850136.1-1850136.12
• /
• 2018

Three-dimensional (3D) mixed phases NiSe nanoparticles growing on the nickel foam were synthesized via a simple one-step hydrothermal method. A series of experiments were carried out to control the morphology by adjusting the amount of selenium in the synthetic reaction. Meanwhile, the as-prepared novel column-acicular structure NiSe exist three advantages including ideal electrical conductivity, high specific capacity and high cycling stability. It delivered a high capacitance of $10.8F\;cm^{-2}$ at a current density- of $5mA\;cm^{-2}$. An electrochemical capacitor device operating at 1.6 V was then constructed using NiSe/NF and activated carbon (AC) as positive and negative electrodes. Moreover, the device showed high energy density of $31W\;h\;kg^{-1}$ at a power density of $0.81kW\;kg^{-1}$, as well as good cycling stability (77% retention after 1500 cycles).

• Applied Microscopy
• /
• v.32 no.4
• /
• pp.319-327
• /
• 2002

Salvinia natans, an unique water fern having a small rootless body, developed three different types of trichomes throughout the plant. The most peculiar type exhibiting rows of obvious, whitish, multicellular trichome clusters was noticed in the upper surface of the floating leaves. Eight to ten branches within a cluster extended ca. $370{\sim}420{\mu}m$ from the leaf surface. No stalk cell was found, however, four large epidermal cells were discernable at the base of four central branches in the cluster. Each branch consisted of $8{\sim}10$ obliquely-oriented small cells that gradually decreased in size toward the branch tip. The second type was found in the lower surface of the floating leaves, stems, and sporocarps. Multicellular uniseriate trichomes, ca. $430{\sim}980{\mu}m$ long, were distributed all over these structures. The tip of trichome was acicular, but a semi-spheric protuberance of approximately $24{\sim}32{\mu}m$ in diameter occurred at the base of each trichome. The protuberance appeared to be firmly attached to the side of the basal cell, however, internal connection to the trichome cell itself was uncertain. The third type was similar to the second in that multicellur uniseriate trichomes with acicular tip and a protuberance at the base were present. However, the trichomes were considerably long relative to the second type, and only occurred along the surface of highly dissected, submerged leaves. A majority of the trichomes exceeded more than 2 mm in length that hung downward in the water. Regardless of trichome type, all trichomes contained a huge central vacuole with very thin cytoplasm, resulting from the fusion of several vacuoles during early trichome development. The various densely-distributed trichomes formed in Salvinia natans probably play an important role in plant buoyancy.