• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.3
• /
• pp.12-18
• /
• 2001

Frequency domain has been used to detect chatter vibration and to decide commencing point of chatter for the milling processes. For this, power spectrum of accelerations signal is analyzed in the frequency domain. Also, the power spectrum and surface roughness are measured, compared, and evaluated according to the depth of cut by experimental works. As a results, it is known that the commencing point of chatter can be decided the behavior of the maximum amplitude of the power spectrum of acceleration signal and there is a correlation between the power spectrum of acceleration signal and the surface roughness. In conclusion, the power spectrum of acceleration signal can be used as a useful information for detec-tion and estimation of chatter vibration in machining.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.4
• /
• pp.417-424
• /
• 2007

This paper presents a solution that an analytical model for an induction motor and the formula of regenerative power and instantaneous torque are derived. based on the spiral vector. The torque is controlled linearly through variations of the slip angular velocity, based on the field acceleration method (FAM). And also PWM inverter fed induction motor drives is schemed to be easily a regenerative drive. The voltage source inverter fed induction motor drives that regenerative power occurs with back current type is presented, to easily controlled the feedback power and to proper the adaption of energy shaving drives. The experimental tests verify the performance of the FAM, proving that food behavior of the drive is achieved in the transient and steady state operating condition, and are discussed to save the power that regenerative power is measured at the operating acceleration or deceleration of servo system.

• Structural Engineering and Mechanics
• /
• v.84 no.2
• /
• pp.155-165
• /
• 2022

The use of electricity and communication between electronic devices is increasing daily, which makes the stability of electrical power supply vital. Since the 1990s, large earthquakes have occurred frequently causing considerable direct damage to electrical power facilities as well as secondary damage, such as difficulty in restoring functions due to the interruption of electric power supply. Therefore, it is very important to establish measures to protect electrical power facilities, such as transformers and switchboards, from earthquakes. In this study, a 154 kV transformer whose service life had expired was installed on the base fabricated by simulating the field conditions and conducting the shaking table tests. The dynamic characteristics and seismic behavior of the 154 kV transformer were analyzed through the resonance frequency search test and seismic simulation test that considers the front, rear, left, and right directions. Since the purpose of this study is to analyze the acceleration amplification in the bushing due to the acceleration amplification, the experimental results were analyzed focusing on the acceleration response and the converted acceleration amplification ratio rather than the failure due to the displacement response of the transformer. The seismic force amplification at the transformer bushing was evaluated by simulating the characteristics of electrical power facilities in South Korea, and compared with the IEC TS 61463 acceleration amplification factor. Finally, the amplification factor at zero period acceleration (ZPA) modified for each return period was summarized. The results of this study can be used as data to define the amplification factor at ZPA of the transformer bushing, simulating the characteristics of electrical power facilities in Korea.

• Earthquakes and Structures
• /
• v.2 no.2
• /
• pp.171-187
• /
• 2011

Rational scaling of design earthquake ground motions for tall buildings is essential for safer, risk-based design of tall buildings. This paper provides the structural designers with an insight for more rational scaling based on drift and input energy demands. Since a resonant sinusoidal motion can be an approximate critical excitation to elastic and inelastic structures under the constraint of acceleration or velocity power, a resonant sinusoidal motion with variable period and duration is used as an input wave of the near-field and far-field ground motions. This enables one to understand clearly the relation of the intensity normalization index of ground motion (maximum acceleration, maximum velocity, acceleration power, velocity power) with the response performance (peak interstory drift, total input energy). It is proved that, when the maximum ground velocity is adopted as the normalization index, the maximum interstory drift exhibits a stable property irrespective of the number of stories. It is further shown that, when the velocity power is adopted as the normalization index, the total input energy exhibits a stable property irrespective of the number of stories. It is finally concluded that the former property on peak drift can hold for the practical design response spectrum-compatible ground motions.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1039-1040
• /
• 2007

This paper is derived a solutions for an analytical model of an induction motor and the formula of regenerative power, based on spiral vector. The torque is controlled linearity through variations of the slip angular velocity, based on the field acceleration method (FAM). And also PWM inverter fed induction motor drives is schemed to be easily a regenerative power. The experimental tests verify the performance of the FAM, proving that good behavior of the drive is achieved in the transient and steady state operating condition. and are discussed to shave the power that regenerative power is measured at the operating acceleration or deceleration of servo system.

• Korean Journal of Applied Biomechanics
• /
• v.27 no.4
• /
• pp.263-268
• /
• 2017

Objective: The purpose of this study was to show differences in impact variables between treadmills with (treadmills B, C, and D) and treadmills without a shock-absorbing function (treadmill A) to propose the development of a treadmill with improved or added shock-absorbing function to reduce impact shock. Method: Thirteen male students in their twenties who had habitual rear foot strike during running ran on four treadmills at 2.67 m/sec while ankle and neck acceleration data were collected. The magnitude of the ankle and neck acceleration peaks and peak positive ankle acceleration were calculated. The power spectral density of each signal was calculated to transform the ankle and neck accelerations in the frequency domain. Results: The peak positive ankle acceleration on treadmill B was significantly lesser than that on treadmills A and D, and that on treadmill C was significantly less than that on treadmill A (p < .01). Peak positive neck acceleration was not statistically different between the treadmills. The frequencies of the peak power of the ankle and neck acceleration signal within the lower and higher frequency ranges were not statistically different between the treadmills. The signal power magnitude of the ankle in higher frequency ranges on treadmill B was significantly less than that on treadmills A, C, and D (p < .01). The signal power magnitude of the ankle in higher frequency ranges was not statistically different between the treadmills. The signal power magnitudes of the neck acceleration signal within the lower and higher frequency ranges were not statistically significantly different between the treadmills. Conclusion: Our results indicate that the shock-absorbing function of a treadmill plays a role in reducing impact shock. Therefore, in future treadmill development, shock-absorbing function should be improved or incorporated to reduce impact shock to the body.

• Journal of Biosystems Engineering
• /
• v.8 no.2
• /
• pp.1-10
• /
• 1983

The resulting characteristics of vibrations show different patterns for the various oscillating mechanisms. These vibrations causes troublesome operation problems for the operators and sometimes for the machines. Furthermore, in some cases the practical usage of this oscillating mechanism is constrained by its mechanical conditions. In this study, a balanced oscillating tillage tool with triple blades having different acting area was designed. The horizontal and vertical oscillating accelerations and draft power requirement due to the various travel speeds, lift angles, amplitudes and oscillating frequencies were investigated in a laboratory soil bin with a soil having invariable properties. The results obtained are summarized as follows: 1. Overall, the horizontal acceleration decreased as the oscillating frequency and amplitude decreased. But the increase in travel speed caused the decrease horizontal acceleration. The blade with the lift angle of $30^{\circ}$ exhibited the lowest value of horizontal acceleration among the blades tested. 2. For the vertical acceleration, the fluctuating trend of oscillating acceleration was similar to the trend of the horizontal acceleration. 3. The draft power requirement decreased as the amplitude and oscillating frequency increased. But the increase in travel speed caused the increase in draft power requirement. The blade with the lift angle of $10^{\circ}$ showed the lowest value of draft power requirement among the blades tested.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.1
• /
• pp.41-48
• /
• 2022

Vehicle vibration was introduced in the time and frequency domains using fast Fourier transform (FFT) analysis. In particular, a vibration mode analysis and characteristics of the frequency response function (FRF) in a sport utility vehicle (SUV) passing over a bump barrier at different speeds was performed systematically. The response behavior of the theoretical acceleration was obtained using a numerical method applied to the forced vibration model. The amplitude and frequency of the external force on the vehicle cause various power spectra with individual intrinsic system frequencies. In this regard, several modes of power spectra were acquired from the spectra and are discussed in this paper. The proposed technique can be used for monitoring the acceleration in a vehicle passing over a bump barrier. To acquire acceleration signals, various experimental runs were performed using the SUV. These acceleration signals were then used to acquire the FRF and to conduct mode analysis. The vehicle characteristics according to the vehicle condition were analyzed using FRF. In addition, the vehicle structural system and bump passing frequencies were discriminated based on their power spectra and other FRF spectra.

• Journal of Applied Reliability
• /
• v.18 no.1
• /
• pp.8-19
• /
• 2018

Purpose: This study has developed the accelerated lifetime test method for smps for outdoor lighting LED through two factors of temperature and humidity. Methods: Acceleration condition was confirmed for each stress and model, and acceleration life test model was estimated according to acceleration condition. Results: As a result of confirming the accelerated life test model, in the case of humidity, acceleration was established only in the foreign products. Therefore, it is confirmed that the acceleration condition is insufficient. However, the estimated parameters for temperature are relatively constant. It is therefore suitable for power supply acceleration tests for outdoor lighting LEDs. Conclusion: The SMPS acceleration test for outdoor lighting LED can improve the availability of the product by developing an accelerated life test method that guarantees the reliability of the product.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.351-356
• /
• 2011

Some materials show the character of rigid body in low frequency spectrum. The rigid body motions are consisted of translational and rotational motions. Especially, we can get the acceleration or displacement of a random point in the rigid body by analyzing rigid body transfer matrix at the car's engine and power train. Actually it is difficult to measure the acceleration by attaching the sensor inside of the engine and power train. So the hard to predict acceleration data can be achieved attaching the sensor on the outside of the engine and power train by analyzing the data of rigid body motion which the engine is operated using dynamo. Also this paper will show the change of predicted data and accuracy variation by not using all the measured data but a few exceptions of the point number.