• International Journal of Railway
• /
• v.6 no.1
• /
• pp.13-25
• /
• 2013

Railpad prevents damage of the tie and ballast by reducing the impact and high frequency vibration, which occurs when a vehicle load transfers to a tie. But elasticity of the railpad can decrease under vehicle load and over usable period. If that happens, railpad will become stiffer. Increase in stiffness of the railpad also translates into a rise in track maintenance cost because it accelerates the damage of the track. In this study, accelerated heat ageing test was performed to predict an expectable lifetime of the railpad. As a result, it was predicted to be about sixteen years at $25^{\circ}C$ that life time of railpad using NR rubber from Arrhenius relationship. Also, it was predicted to be about thirty-two days at $100^{\circ}C$. At this time, a standard rate of thickness change is approximately within 12%.

• Journal of the Korean Society for Railway
• /
• v.7 no.4
• /
• pp.307-311
• /
• 2004

Arresters are the best protective device on electrical power systems against transient overvoltages generated by lightning and/or switching operation. Nonetheless, arresters are deteriorated by absorption of moisture in the environments of its use, repetition in the protective operation to overvoltages, and some defects at manufacturing. It is therefore important to estimate the electrical characteristic changes of ZnO blocks. In this paper, an accelerated ageing test by a standard lightning impulse current was carried out to extract parameters needed for arrester diagnosis, and leakage current components were measured. Total energy applied to the ZnO blocks at each time is about 1,050[J] in 8/20[${\mu}\textrm{s}$] impulse current. From the experimental results, we proposed electrical parameters and leakage current level to diagnose arrester soundness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.562-563
• /
• 2005

In case of aged porcelain, the failure in basic performance tests happened in cool-heat tests. Based on this characteristic, we studied the method predicting failure phenomena through more severe accelerated cool-heat ageing and accelerating thermal mechanical performance tests. Test results indicated that the thermal stress by temperature gradient was more severe parameter than thermal stress by quenching cycles within a category of standard or accelerating methods. And there is no the deterioration of statistic strength, but the deterioration of strength according to accelerating tests is serious.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.59 no.4
• /
• pp.457-462
• /
• 2014

This study was conducted to evaluate basic seed characteristics such as morphological characteristics and various seed vigor using 4 sorghum varieties, Nampungchal, Donganme, Hwanggeumchal and Whinchal. No difference was shown in morphological characteristics of the varieties except that the width. Whinchal has bulb-shaped seed, while the other varieties have oval-shaped seeds. The seed coat color of Whinchal is obviously different from those of the other varieties; especially, Nampungchal and Hwanggeumchal are not glossy. Germination rate were Hwanggeumchal > Nampungchal > Donganme > Whinchal in the order of higher rate in standard germination tests and cold germination test. In the ageing test, Donganme showed the lowest 15% decrease in comparison with the standard cultivar. Electric conductivity (EC) has negative correlation with standard germination tests, cold germination test and accelerated ageing test. In the percentage of emergence (PE), Hwanggeumchal was the highest 85.7% which was more than 40% to the lowest Whinchal. Mean emergence time (MET) showed significant difference between the varieties; Whinchal showed the slowest 6.0 days.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.4
• /
• pp.151-159
• /
• 2001

As huge energy transfer systems like a nuclear power plant, steam power plant and petrochemical plant are operated for a long time, mechanical properties are changed by degradation. The life time of the systems can be affected by the mechanical properties. BI(Ball Indentation) test has a potential to replace conventional fracture tests like a uniaxial tensile test, fracture toughness test, hardness test and so on. In this paper, we would like to present the ageing evaluation technique by the BI method. The four classes of the thermally aged 1Cr-!mo-0.25V specimens were prepared using an artificially accelerated aging method. Tensile tests, fracture toughness tests, hardness tests and BI tests were performed. The results of the BI tests were in good agreement with fracture characteristics by a standard fracture test method within 5%. The IDE(Indentation Deformation Energy) of a BI technique as a new parameter for evaluating a degradation was suggested and the new IDE parameter clearly depicts the degradation degree.

• Fibers and Polymers
• /
• v.7 no.3
• /
• pp.286-294
• /
• 2006

This study has examined the flexural properties of natural and chemically modified coir fiber reinforced cementitious composites (CFRCC). Coir fibers of two different average lengths were used, and the longer coir fibers were also treated with a 1% NaOH solution for comparison. The fibers were combined with cementitious materials and chemical agents (dispersant, defoamer or wetting agent) to form CFRCC. The flexural properties of the composites, including elastic stress, flexural strength, toughness and toughness index, were measured. The effects of fiber treatments, addition of chemical agents and accelerated ageing of composites on the composites' flexural properties were examined. The results showed that the CFRCC samples were 5-12 % lighter than the conventional mortar, and that the addition of coir fibers improved the flexural strength of the CFRCC materials. Toughness and toughness index, which were associated with the work of fracture, were increased more than ten times. For the alkalized long coir fiber composites, a higher immediate and long-term toughness index was achieved. SEM microstructure images revealed improved physicochemical bonding in the treated CFRCC.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.13 no.1
• /
• pp.92-100
• /
• 2017

Due to the presence of ferrite phase in the finished welds, austenitic stainless steel welds (ASSWs) are considered susceptible to the thermal aging embrittlement during long-term service in light water reactor environment. In this study, the thermal aging embrittlement of typical ASSWs, E308 and ER316L welds, were evaluated after the long-term exposure up to 20,000 h at $400^{\circ}C$, which is considered as an accelerated thermal aging condition. After thermal aging, the decrease of tensile ductility and fracture toughness was observed. The microstructure observation with high resolution transmission electron microscopy revealed that spinodal decomposition in ferrite phase of both E308 and ER316L welds would be the main cause of the degradation of mechanical properties. Also, it was shown that the difference of thermal ageing embrittlement between ER316L and E308 welds was significant, such that the reduction of fracture resistance for ER316L weld was much larger than that of E308 weld.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.9
• /
• pp.842-850
• /
• 2003

The suspension insulators are subjected to harsh environments in service for a long time. The long-term reliability of tile insulators is required for both mechanical and electrical performances. This study describes some basic performance tests and accelerated aging test by cool-heat cycling methods and thermal mechanical performance test methods on alumina porcelain insulators (new and aged) used for transmission line in KOREA. There was no fail in electrical and mechanical performance tests such as a high voltage strength, a flashover voltage, and an impact strength in all samples. But in the case of accelerating aging tests which have above 9$0^{\circ}C$ temperature gradient, fracture phenomena was happened by a thermal shock in tile aged sample(sample A) with low alumina porcelain body. It was indicated that sample A was more severely aged than other samples. According to results of HRB test and microstructural analysis, it was reasoned that insulator bodies with the matrix reinforced with alumina crystalline phase have advantages over the suppression of crack advance. And cool-heat aging and mechanical thermal ageing tests shows that a temperature gradient is more effective to accelerating than a cycling number.

• The Korean Journal of Nuclear Medicine
• /
• v.24 no.2
• /
• pp.222-228
• /
• 1990

The development of histomorphometric and histodynamic investigations has permitted the description of a specific and complex osteopathy in hyperthyroidism. The increased bone turnover rate in hyperthyroid patients may be accompanied by a considerable bone loss. These features are associated with both inclosed osteoclastic bone resorption and increased osteoblastric bone formation, with an accelerated calcification rate. Conventional biochemical markers of bone metabolism, i.e. serum calcium and alkaline phosphatase and urinary hydroxyproline and calcium are normal in most patients with hyperthyroidism. However, the correlation between serum BGP and serum concentration of thyroid hormon suggests that serum BGP may be a sensitive marker of increased bone formation due to the hypersecretion of thyroid hormones. Any increase in bone turnover, whether focal or diffuse, will result in an increase in $^{99m}Tc-methylenediphosphonate$ uptake (MDP). The measurement of this uptake in hyperthyroid patients by bone provides a sensitive and objective means of quantifying skeletal metabolism. Using a standard shadow-shield whole-body monitor and radioimmunoassay kit, we have measured whole-body retention of $^{99m}Tc-MDP$ up to 24hr and concentration of serum Osteocalcin in 20 patients with hyperthyroidism and in 42 normals. The results were as follows; 1) The average of serum Osteocalcin level in 42 patients with normals was $9.90{\pm}4.87(ng/ml)$ and in 20 patients with hyperthyroidism was $19.54{\pm}5.7(ng/ml)$. Both the averages of serum Osteocalcin and 24hr $^{99m}Tc-MDP$ uptakes in hyperthyroid patients were higher than those in normals. 2) $^{99m}Tc-MDP$ uptakes in skeletal system increased in proportion to normal ageing after 40 yrs old in 42 patients with normals. The average of $^{99m}Tc-MDP$ uptakes in hyperthyroid patients were higher than those in normals without related ageing. 3) A significant relationships between the $^{99m}Tc-MDP$ uptakes and serum Osteocalcin level were peformed (r=0.55, $y=17.58+6.7\times$). From the above results we concluded that the measurement of serum Osteocalcin and 24hr $^{99m}Tc-MDP$ uptakes can be used for evaluation of bone turnover as a specific marker in hyperthyroid patients.

• Journal of Conservation Science
• /
• v.34 no.6
• /
• pp.459-470
• /
• 2018

Cellulose nitrates were used for folklore artifacts(ornamental beads and pipes in hatstrings, frames of eyeglasses, ornamental eyeglass cases, headband ornaments, and jeogori buttons) between the 19th and 20th centuries; however, they are susceptible to cracking, crazing, embrittlement, and crumbling due to deterioration. To consolidate and adhere deteriorated cellulose nitrate folklore artifacts, water-soluble acrylic emulsion adhesives were investigated. For consolidation, Plextol D 498, which has the lowest viscosity in low concentrations, was used. In adhesive films whose glass transition temperature(Tg) is lower than room temperature, the tensile stress and modulus decreased and the strain increased; therefore, the flexibility was high. The Plextol D 498 and Plextol D 498 and Dispersion K 52 films maintained their adhesiveness and flexibility after artificial-sunlight-accelerated ageing, and Plextol D 498 and Dispersion K 52 films hardly caused yellowing. Plextol D 498 was the most stable for accelerating ageing. A low concentration of Plextol D 498 emulsion resulted in the best permeability on the surface of cellulose nitrate, compared with other acrylic emulsions. To prevent ornamental hatstrings from cracking, crazing, embrittlement, and crumbling, a Plextol D 498 emulsion was used. After applying low concentrations(1%, 3%) of the emulsion to consolidate the fragments and high concentration to adhere the fragments, the ornamental hatstrings were protected from crumbling by deterioration, and their fragments were well-adhered. To preserve it from deterioration by oxygen and humidity, the treated ornament was sealed with an oxygen-barrier film using a low-humidity oxygen scavenger.