• Composites Research
• /
• v.22 no.6
• /
• pp.32-38
• /
• 2009

In this study, the energy absorption capabilities and failure modes of four different kinds of circular tubes made of carbon, Kevlar and carbon-Kevlar hybrid composites with epoxy resin have been evaluated. In order to achieve these goals, these tubes were fabricated with unidirectional prepregs and compressive tests were conducted for the tubes under 10mm/min loading speed. From the test results, carbon/epoxy tubes were collapsed by brittle fracturing mode and showed the best energy absorption capabilities, while Kevlar/epoxy tubes were crushed by local buckling mode and worst. The hybrid [$90_C/0_K$] tubes were failed in a local bucking mode and showed good post crushing integrity, whereas [$90_K/0_C$] tubes were failed in a lamina bending mode and bad post crushing integrity.

• Korean Journal of Plant Resources
• /
• v.20 no.4
• /
• pp.267-271
• /
• 2007

This study was carried out to examine optimal hot water treatment time in Albizzia julibrissin seeds. Germination and moisture absorption characteristics among intact seeds, immersed seeds for 24 hours in distilled water and hot water treated seeds were surveyed. As result, treated seeds showed a highly significant difference with intact and immersed seeds (p<0.0l). Especially, treated seed for 2.0 minutes represented the highest percent of germination (PG). But mean germination time (MGT) did not have significant difference between non-treatment and treatments (p=0.502). Germination speed and germination performance index showed similar tendency with PG. In percent of moisture absorption (PMA) and moisture absorption rate constant (MARC) treatments had higher values than non-treatment whereas 2.0 minutes treatment was lower than non-treatment in initial moisture absorption rate (IMAR). In relation between germination properties and moisture absorption characteristics, all properties except MGT among germination properties had high correlations with PMA and MARC ($r=0.854{\sim}0.931$,p<0.01) whereas IMAR didn't have correlation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.163-164
• /
• 2006

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.229-234
• /
• 2001

The aluminum extruded sections are used to the light construction of the high speed rail vehicle structures. However, the research works on the crashworthy design of aluminum extruded sections are not published sufficiently. In this paper, the collapse characteristics of aluminum extruded sections are investigated by crush test and simulation. The scale model studies are also performed to predict the impact energy absorption characteristics of full scale model through axial crush test and simulation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.568-573
• /
• 2003

This paper describes a study of terrestrial digital TV transmission systems using wideband opto-electronic techniques such as electro-absorption modulators, wavelength division multiplex to support cost effective, high speed, flexible and interactive digital TV networks including ultra-high speed subscriber networks. In particular, the national DTV networks to be installed is required huge amount of cost. Therefore, the network should be carefully designed for DTV, communication and multimedia services in the future. In this paper, wideband optoelectronic DTV systems are suggested.

• Food Science and Biotechnology
• /
• v.16 no.5
• /
• pp.783-788
• /
• 2007

An advantage to the extrusion of raw potatoes is a reduction in the energy input required to process potato products; however, the effects of extrusion on the properties of raw potato have not been studied. The purposes of this study were to develop a workable extrusion process for raw potato and to study the effects of extrusion conditions on the pasting properties of extruded potato products. The peak viscosity, final viscosity, pasting temperature, water solubility index, and water absorption index of pressed and pressed-dried potato extrudates decreased as die exit temperature increased, whereas they did not change as screw speed increased. The peak viscosity, final viscosity, and water solubility of steam-cooked potato products decreased with extrusion processing; however, they did not change with increasing die exit temperature and screw speed. Potato products with different degrees of depolymerization of extruded potato starch, depending on die exit temperature, were produced from raw potatoes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.342-345
• /
• 1997

We fabricated the sample of u1tra thin lipid membrane(L-${\alpha}$-DLPC ) by LB methode. The $\pi$-A isotherm of the DLPC was measured at the air-water interface varying with the compressing speed and amounts of solutions for spreading. For good property of lipid monolayer film, it was necessary for the lower speed of compressing, and 40${\mu}\ell$ of solutions for spreading. The molecular arrangement of deposited films were evaluated by measuring the absorption, transmitance and intensity with the UV spectrophotometer. The Y-type multilayers prepared at 50mN/m showed weaker than Z-type. So we found building-up of structurally high quality LB films is essential to study properties of the films and to get reproducible data.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.640-643
• /
• 2003

We present investigations of the surface micromachining for transparent glass substrate, e.g. soda lime glass using tightly focused 800nm Ti:sapphire femtosecond laser. In this study, experiment conditions such as laser intensity, scanning speed, focus position were controlled as variable parameters to decide optimal machining conditions. This study shows clearly that laser intensity and scanning speed are dominant factors for good surface morphology. Using the optimal conditions, grooves with 50${\mu}{\textrm}{m}$ line width were fabricated on glass substrate and their surface morphologies were investigated from SEM image.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.1
• /
• pp.201-210
• /
• 1994

A theoretical heat-flow model incorporating with a constant moving CO$_{2}$ laser beam has been analyzed to predict depth and the shape of bead section during last beam welding. The laser beam is exponentially attenuated with an abosrption coefficient in the material. The solution can be expressed in terms of normalized variables. The experimental data were generated by usint CW 2 CO$_{2}$ laser with multi beam mode and CW 3 kW CO$_{2}$laser with Gaussian mode. The specimens were made as bead-on-plate welds for SM 10C, STS 304, STS 316, STS 420 and pure Nickel. The maximum possible penetration depth and the shape of beas section for given sources of laser power, travel speed and beam spot size can be prdicted with this model in a given material.

• Journal of the Korean Society for Railway
• /
• v.5 no.4
• /
• pp.231-236
• /
• 2002

Todays, crash safety requirements of the railway vehicle structures become important design criterion according to the increased driving speed and the lightweight construction. Although the crash analysis using computer simulation can be effectively applied to predict the crash performance of the railway vehicles in the early design stage, the optimized design w.r.t the crash safety could be realized by the crash tests with actual prototype vehicles. However, it is very expensive and time-consuming task to perform the crash test of the railway vehicles. As a measure to cope with the problem, in this paper, the scale modeling technique is suggested and experimentally verified to predict the impact energy absorption characteristics of full scale model of aluminum extrusions sub-structures and the high-speed railway vehicle structure.