• ETRI Journal
• /
• v.23 no.3
• /
• pp.97-105
• /
• 2001

$1.6\;{\mu}m$ emission originated from $Pr^{3+}:\;(^3F_3,\;^3F_4)\;{\longrightarrow}\;^3H_4$ transition in $Pr^{3+}-\;and\;Pr^{3+}/Er^{3+}$-doped selenide glasses was investigated under an optical pump of a conventional 1480 nm laser diode. The measured peak wavelength and fullwidth at half-maximum of the fluorescent emission are ~1650nm and 120nm, respectively. A moderate lifetime of the thermally coupled upper manifolds of ${\sim}212{\pm}10{\mu}s$ together with a high stimulated emission cross-section of ${\sim}(3{\pm}1){\times}10^{-20}\;cm^2$ promises to be useful for $1.6{\mu}m$ band fiber-optic amplifiers that can be pumped with an existing high-power 1480 nm laser diode. Codoping $Er^{3+}$ enhances the emission intensity by way of a nonradiative $Er^{3+}:\;^4I_{13/2}\;{\longrightarrow}\;Pr^{3+}:\;(^3F_3,\;^3F_4)$ energy transfer. The Dexter model based on the spectral overlap between donor emission and acceptor absorption describes well the energy transfer from $Er^{3+}$ to $Pr^{3+}$ in these glasses. Also discussed in this paper are major transmission loss mechanisms of a selenide glass optical fiber.

• Journal of Welding and Joining
• /
• v.35 no.3
• /
• pp.28-34
• /
• 2017

The authors derived the criteria on the process parameters of laser depositions with metal powers(SUS316L & IN718) by evaluating the surface and cross-section properties of the deposition layers. The surface characteristics of the deposition layer are investigated through optical microscopy by controlling the process parameters of laser output, powder feeding rate and gas feeding rate. The cross-section characteristics were also analyzed after polishing and chemical etching process. As the gas feeding rate increased, the amount of powder loss increased and the difference in the dilution ratio and heat affected zone depending on laser outputs was observed. In addition, the powder feeding rate used in the experiment did not interfere with the energy absorption of the base material.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.34 no.6
• /
• pp.466-472
• /
• 2012

The loss of mandibular continuity due to trauma, neoplasm, or infection results in major esthetic and biologic compromise. The reconstruction of the mandibular bone defect still poses a challenge to oral and maxillofacial surgeons. There have been a number of variety graft materials. Among them, free block bone graft with rigid fixation has been widely used. However, cases using free block bone grafts may lead to a marked invasion of the donor site, mal-union, and absorption of the block bone. In this respect, particulate cortical bone using a titanium mesh tray can be an effective alternative option in order to achieve a proper bone contour and good oral rehabilitation. We have developed an intraoral approach for the mandibular reconstruction method using a titanium mesh tray with autogenous particulate cortical bone graft.

• Journal of Life Science
• /
• v.9 no.3
• /
• pp.241-247
• /
• 1999

Antibiotics have been routinely used to control the disease of farm-raised animals in the aquaculture facilities without any criterion based on a pharmacokinetic study. This lack of information on the effective usage of antibiotics would have brought the farmers to use excessive and/or less dosages, causing the advent of drug-resistant bacteria as well as economic loss and possible contamination of the local farming area. Until recently, few studies on a detailed manual for the antibiotic usage including chemotherapy procedure, dosage, and treatment schedule of the aquatic antibiotics have been conducted throughout the world. To the worse, there is no available criterion for optimal usage of aquatic antibiotics to control diseases in aquatic farms in this country because every country has its own aquacultural system. Therefore, based on the previous studies on the usage of the various antibiotics, our studies are to focus on the development of optimal method for the detection of various antibiotics on the fate of antibiotics applied to the fish, including absorption, circulation, and secretion physiology. Pharmacokinetic study were to sep up the optimal detective condition against residual antibiotics of fish by HPLC. The grinding pefloxacin for 15 min is most effective in dissolution test and pharmacokinetic parameters. Pharmacokinetic parameters were satisfactory for 15 min-grinding products and they can be explained as one-compartment model.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.8
• /
• pp.661-668
• /
• 2016

Oil deflector prevents oil leakage that occurs in thermoelectric power plant at operating lubricant facilities. Vibration of rotating rotor-induced wear of aluminum tooth in existing oil deflector leads to oil leakage as well as life shortening of the tooth. In this study, an advanced oil deflector was developed for shock absorption and prevention of wear by decreasing clearance (from 0.5 mm to 0.2 mm) between rotor and tooth to minimize oil leakage, and by replacing 2 aluminum teeth in outmost of the oil deflector with hi-performance seal made of engineering plastic. The CFD results were compared between advanced vs. existing oil deflector to determine the amount of oil loss. Structural safety was verified through impact analyses according to the three kinds of engineering plastics, considering cost efficiency, and optimal material of hi-performance seal was chosen.

• The Korean Journal of Ceramics
• /
• v.2 no.2
• /
• pp.89-94
• /
• 1996

Aluminum and zinc titanium silicate sol-gel films were fabricated for application of waveguide and the effect of additions of ZnO and $Al_2O_3$ to binary titanium silicate films was investigated. During firing, the films are densified as they shrunk and their refractive index increases in the range of 1.58-1.83 depending on the film composition. The attenuation of the waveguides is not sensitive to changes in composition except for zinc titanium silicate waveguides which have substantially higher attenuation. However, the increase in the attenuation with aging of the waveguides depend upon the composition of waveuides. The addition $Al_2O_3$ or the reduced $SiO_2$ content in the composition appears to slow the deterioration of the waveguides due to the formation of more stable bonds and increased acidity on the film surface. Also, the wavelength dependence of the attenuation of the waveguides varies with composition. The attenuation of the waveguides except for the $65SiO_2{\cdot}35TiO_2$ composition are not Rayleigh scatter limited, suggesting the absorption loss of the waveguides due to the effects of residual carbon and structural defects in the films.

• Advances in environmental research
• /
• v.3 no.4
• /
• pp.337-353
• /
• 2014

The determination of the effectiveness of the immobilization of blasting dust (waste generated in galvanic activities) in cement matrix, as well of mechanical, physical and microstructural properties of concrete paving blocks produced with partial replacement of cement was the objective of this work. The results showed that blasting dust has high percentage of silica in the composition and very fine particle size, characteristics that qualify it for replacement of cement in manufacturing concrete blocks. The replacement of Portland cement by up to 5% residues did not cause a significant loss in compressive strength nor increase in water absorption of the blocks. Chemical tests indicated that there is no problem of leaching or solubilization of contaminants to the environment during the useful life of the concrete blocks, since the solidification/stabilization process led to the immobilization of waste in the cement mass. Therefore, the use of blasting dust in the manufacture of concrete paving blocks is promising, thus being not only an alternative for proper disposal of such waste as well as a possibility of saving raw materials used in the construction industry.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.490-491
• /
• 2007

We have investigated dielectric polarization in organic light-emitting diodes using 8-hydroxyquinoline aluminum$(Alq_3)$ as an electron transport and emissive material. We analyzed the dielectric polarization of organic light emitting diodes using impedance. Impedance characteristics was measured complex impedance Z and phase ${\theta}$ in the frequency range of 40Hz to $10^8Hz$. We obtained dielectric constant and loss tangent (tan ${\delta}$) of the device. From these analyses, we are able to interpret a dielectric dispersion and dielectric absorption contributed by an interfacial and orientational polarization.

• Korean Journal of Materials Research
• /
• v.16 no.11
• /
• pp.663-667
• /
• 2006

CTAB(cetyltrimethylammonium bromide)-capped CdSe nanoparticles were prepared by using a 4 : 1(v/v) distilled water-isopropyl alcohol mixture. The cadmium chloride and sodium selenosulfate were used as the cadmium and selenium source. By the analysis of XRD and XPS, the resultant particle was confirmed to be cubic CdSe phase. TEM image showed CdSe nanoparticles with empty core. The CTAB-capped sample showed an maximum absorption at 418nm, blue-shifting compared with bulk CdSe, which indicated stronger quantum confinement effect compared with uncapped sample. From FT-IR analysis, it was found that the presence of the new peaks in the $850{\sim}1250cm^{-1}$ range indicated the existence of chemical bonding between CTAB and surface of CdSe nanoparticles. Also TG analysis indicated that there were two weight-loss steps for the CTAB-capped CdSe nanoparticles. It was suggested that CTAB played a significant role in protecting CdSe nanoparticles.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.307-310
• /
• 2000

Recently, the demand for the Floating, Production Storage, and Offloading facility(FPSO) which has some economic and technical advantages, has increased in offshore oil production areas. The basic characteristics of a 343,000 DWT class FPSO which is being built in Hyundai Heavy Industries and shall be installed in offshore Angola, is almost same as that of oil carriers. However, she do not have self-propulsion system, but has additional facilities for oil production and positioning system. Main noise source contributing to the cabin noise of the accommodation, are classified into the machine in the engine room and the deckhouse, HVAC system, and the topside equipments. In general, the noise regulation for the offshore structure is much severer than that of the common commercial ships and the maximum acceptable sound pressure level of cabins is specified in 45dB(A). This paper describes the procedure of noise analysis along with its results. Noise analysis has been carried out for the case of emergency diesel generator running condition and the case of normal production condition and the results has been compared with the measurement results of the first case. Based on the results, proper countermeasures to reduce excessive noise level has been applied considering the characteristics of sources and receiver spaces and can be satisfied the specifications at all spaces.