• 한국분말재료학회지
• /
• 제13권6호
• /
• pp.450-454
• /
• 2006

Wear of steel plate was measured during unlubricated sliding against TiC composites. These composites consist of round TiC grains and steel matrix. TiC grain itself exhibits low surface roughness and round shape, which does not bring its counterpart into severe damage from friction. In our work a classical experimental design was applied to find out a dominant factor in counterpart wear. The analysis of the data showed that only the applied load has a significant effect on the counterpart wear. Wear rate of counterpart increased non-linearly with applied load. Amount of wear was discrepant from expectation of being in proportion to the load by analogy with friction force. Our experimental result from treating matrix variously revealed bimodal wear behavior between the composites and counterpart where a mode seems to result from the special lubricant characteristic of TiC grains, and the other is caused by metal-to-metal contact. The two wear mechanisms were discussed.

• 한국가구학회지
• /
• 제17권1호
• /
• pp.83-89
• /
• 2006

Because the surface of pine wood is very soft, there have been many attempts, like as surface coating, resin impregnation, and densificationt, to harden the surface of wood for its interior use. This study was carried out for surface hardening of pine wood by laminating of melamine resin sheet. The effect of laminating method on the characteristics of melamine resin sheet-laminated wood(MLW) was investigated. Flat-sawn softwoods were suitable for MLW making. And the pre-drying of wood at $105^{\circ}C$ for 30min, before laminating, was effective for preparing of defect-free MLW. The abrasion resistance of pine wood was greatly improved by laminating of melamine resin sheet on its surface. Consequently, the laminating of melamine resin sheet was proved to be a favorable method for improvement of surface abrasiveness of pine wood.

• 한국의류학회지
• /
• 제42권3호
• /
• pp.486-502
• /
• 2018

Mass-production caused by industrialization has led to environmental pollution; however, a potential solution to this problem is the Up-cycling fashion design belonging to the sustainable design category. This study analyzed the material characteristics of each brand fashion product by selecting 21 domestic Up-cycling fashion brands. The product types manufactured by domestic Up-cycling fashion brands could be divided into fashion clothing, bag, and fashion accessories. The materials used for each item included special material, waste fiber, waste leather, waste paper, and others. In the results of analyzing the material characteristics into the external characteristics and internal characteristics, the external characteristics included the durability with less abrasiveness and deformation as well as a mixture with other different materials, while the internal characteristics included a story arousing consumers' empathy, and scarcity without the same design due to the limitation of material.

• Tribology and Lubricants
• /
• 제39권3호
• /
• pp.111-117
• /
• 2023

This paper presents an experimental investigation of the tribological characteristics of PTFE composites filled with nano CuO particles under low sliding speed and load. All the specimens were prepared by sintering. Before sintering, the mixture of PTFE powder and CuO particles were mixed by a high-speed mixer using CuO volume fractions of 0.2 vol. % and 5 vol. %. Each mixture was sintered at 350 ℃ for 30 min on the steel disk. We conducted ball-on-disk sliding test an hour using a steel ball against PTFE composites, including pure PTFE. The load and sliding speed used was 2 N and 0.01 m/s, respectively. Adding nano CuO particles increases the friction coefficient because of the abrasiveness of hard nano CuO particles. The highest coefficient of frictions was obtained from 5 vol. % CuO. Conversely, the lowest wear of the composites was obtained from the 5 vol. % CuO nanocomposite. This study reveals that the addition of nano CuO particles can lower the wear of PTFE, despite an increase in the coefficient of friction. However, the coefficient friction is still moderate compared to other engineering polymers. In addition, the amount of CuO nano particles has to be optimized to reduce friction and wear at the same time.

• 대한치과기공학회지
• /
• 제45권2호
• /
• pp.48-53
• /
• 2023

Purpose: This study aimed to provide the basic data for dental barrel finishing by observing the abrasiveness of the metal body according to the time of the barrel finishing. Methods: This study included three types of Co-Cr alloys. The specimens were manufactured by casting method using 10-mm diameter wax spheres (n=10). The cast alloys were polished for 60 minutes at intervals of 5 minutes in barrel finishing. The weight and volume of the specimens were measured, and the rate of change was calculated. The data obtained from the three groups (α=0.05) were compared and analyzed using one-way ANOVA. Results: As a result, the overall volume and weight of the group decreased after grinding compared with the control group. Conclusion: When grinding dental barrel finishing, no difference was observed in the processing rate depending on the type of alloy and the processing rate of the alloy body is within 30 minutes; hence, dental barrel finishing can be effectively used for grinding.

• 한국터널지하공간학회 논문집
• /
• 제16권2호
• /
• pp.237-248
• /
• 2014

TBM의 사양을 설계하고 굴진성능을 예측할 때 실대형 선형절삭시험을 통하여 설계변수를 획득하는 것이 매우 효과적인 방법인 것으로 알려져 있다. 하지만 선형절삭시험을 위해서는 대형 시편을 획득하고 큰 하중용량의 시험을 수행하는 과정에서 상당한 비용과 노력이 소모된다는 단점이 있다. 따라서 선형절삭시험을 대체하는 경험적 예측 모델, 즉 CSM모델과 NTNU모델을 사용하여 몇 가지 지수를 산정하고 이로부터 설계변수를 추정하는 경우가 많다. 본 연구에서는 압입시험 및 세르샤 마모시험을 이용하여 TBM의 사양(추력, 토크)과 굴착에 따라 소요되는 디스크 커터의 개수를 추정하는 방법에 대하여 고찰하였다. 압입시험과 세르샤 마모시험은 TBM의 설계 변수를 추정하기 위한 유용한 시험법이나 그 활용법이 연구 되고 있지 못한 실정이다. 이 연구에서는 압입시험과 세르샤 마모시험결과를 간단한 형태의 지수형태로 도출하고 이를 선형절삭시험 및 실제 굴진자료와 비교하여 상관관계를 도출하고 이로 부터 디스크 커터의 작용력 및 수명을 예측하였다. 또한 이 일련의 계산 과정을 프로그램화 하였으며, 터널의 연장 정보, TBM의 기계정보, 구간별 암석의 물성을 입력변수로 하여 구간별 굴진율과 TBM 사양 및 운영조건, 디스크 커터의 소모개수를 예측할 수 있었다.

• 대한치과보철학회지
• /
• 제41권2호
• /
• pp.136-147
• /
• 2003

Statement of problem : Ceramic and composite resin have been used to fulfill the demand for esthetic prosthesis. However, ceramic is easy to break and wears off the opposite natural teeth. Conventional composite resin also has low abrasive resistance and color stability. Ceramic Optimized Polymer (ceromer) was developed in mid-1990s to overcome the shortfalls of ceramic and composite resin. Ceromer has similar abrasiveness with the natural tooth and has relatively high strength. Color stability affects esthetics and long-term prognosis of the prosthesis. Purpose The purpose of this study was to compare color stability of ceromers(2 types : $Artglass^{(R)}$. $Targis^{(R)}$) with ceramics ($Vintage^{(R)}$-polishing, $Vintage^{(R)}$-glazing). Material and Method : The color difference(${\Delta}E^*$) was measured by spectrophotometer with different immersion time. Twenty disks, 3mm in thickness and 10mm in diameter, were fabricated for each specimen in shade A2(Vita Lumin shade guide), Specimens (5 samples in each group) were immersed in the food colorants (Red no.3. Yellow no.4, Blue no.1, Distilled water) for 24 hours, 48 hours and 72 hours respectively. $L^*,\;a^*$ and $b^*$ value were measured with spectrophotometer (CM 503i : Minolta Co., Japan) and mean ${\Delta}E^*$ value was calculated for statistical analysis Results : The results of this study were obtained as follows. 1. The ${\Delta}E^*$ values of all test samples increased with the time of immersion. 2. The ${\Delta}E^*$ values of all materials increased in order of Distilled Water, Yellow no.4, Blue no.1 and fed no.3. There was significant difference between Red no.3 and the other food colorants(p<0.05). 3. The ${\Delta}E^*$ values increased in order of $Vintage^{(R)}$-glazing, $Vintage^{(R)}$-polishing. $Artglass^{(R)}$ and $Targis^{(R)}$. There was significant difference between $Vintage^{(R)}$-glazing and the other materials (p<0.05). Conclusion : By means of the above results, immersion time was found to be a critical factor for color stability of ceromer. For the long-term color stability of prosthesis it is recommended patients having ceromer prosthesis ($Artglass^{(R)},\;Targis^{(R)}$) to reduce the habitual intake of Red no.3 colorants con taming foods.