• Elastomers and Composites
• /
• 제58권3호
• /
• pp.103-111
• /
• 2023

The abrasion resistances of silica-filled styrene-butadiene rubber (SBR) compounds prepared with and without dicyclopentadiene resin (SBR-R and SBR-0, respectively) were studied using four different abrasion testers, namely cut and chip (CC), Lambourn, DIN, and laboratory abrasion tester (LAT100). The effect of the resin on the abrasion behavior was elucidated by analyzing the morphologies and size distributions of wear particles. All the wear particles had rough surfaces, but those obtained in the Lambourn abrasion test exhibited relatively smooth surfaces. The size distributions of the wear particles showed different trends depending on the abrasion tester and the rubber compound; however, most of the wear particles were larger than 1000 ㎛. The SBR-R sample showed a wide range of particle sizes (from 63 ㎛) in the LAT100 abrasion test and majority of the wear particles were 500-1000 ㎛, whereas the SBR-0 sample had the most distribution of larger than 1000 ㎛. The abrasion rates of SBR-0 sample were lower than those of the SBR-R sample for the CC and LAT100 abrasion tests, but the Lambourn abrasion test result showed the opposite trend. Addition of the resin influenced the abrasion behavior, however the effect varied depending on the type of abrasion tests.

• Elastomers and Composites
• /
• 제58권2호
• /
• pp.87-94
• /
• 2023

Abrasion tests of an SBR compound were conducted using four different types of abrasion testers (cut and chip, Lambourn, DIN, and LAT100). The abrasion test results were analyzed in terms of size distributions and morphologies of the wear particles. Most wear particles were larger than 1000 ㎛. The wear particle size distributions tended to decrease as the particle size decreased. Except for the Lambourn abrasion test, the wear particles smaller than 212 ㎛ were rarely generated by the other three abrasion tests, implying that small wear particles were produced through friction by introducing talc powder. Shapes of the wear particles varied depending on the abrasion testers. The wear particles generated from the Lambourn abrasion tester had stick-like shapes. The cut and chip abrasion test showed a clear abrasion pattern, but the DIN abrasion test did not show any specific abrasion pattern. The Lambourn and LAT100 abrasion tests showed irregular abrasion patterns.

• Elastomers and Composites
• /
• 제56권1호
• /
• pp.12-19
• /
• 2021

The abrasion behaviors of NR/BR blend vulcanizates were investigated using NR/BR = 100/0, 80/20, and 60/40 compounds. The abrasion test was performed using a laboratory abrasion tester (LAT) at slip angles of 1° and 7°. The size distributions of the wear particles and the abrasion rates were examined according to the rubber compositions and slip angles. The most abundant wear particles at the slip angle of 1° were sizes above 1,000 ㎛, irrespective of the rubber composition. The most abundant wear particles at 7° slip angle had sizes in the range of 212-500 ㎛, except for the NR = 100 sample. The wear particle size distribution shifted to a smaller size as the slip angle and BR content increased. The abrasion rate at 7° was much larger than that at 1° slip angle. Furthermore, the abrasion rate was notably increased by adding BR to NR.

• 청정기술
• /
• 제11권3호
• /
• pp.153-164
• /
• 2005

This study found a reliable evaluation for four kinds of pb-Free plating solutions and it's layers, through pure Sn, SnAg, SnBi and SnCu. These four kind of solutions are widely used to pb-Free plating. Hull-cell, Harring-blum, coverage, throwing power, current efficiency, stability, life-time, composition, hardness, roughness, abrasion, scratch, solderability, corrosion, contact angle, morphology, SIR(Surface insulation resistance) and Whisker test were experimented. Also, Using ICP, XRF, FE-SEM, EDS, temperature/humidity chamber, solderability tester, hardness tester, roughness tester, abrasion tester, salt spray tester, contact angle tester, SIR tester, and microscope. In this paper could be shown the systematic and various analysis for reliability about four kinds of pb-Free plating solutions, processes and it's deposit surface.

• 한국터널지하공간학회 논문집
• /
• 제20권6호
• /
• pp.1091-1104
• /
• 2018

암반용 TBM 공사에서 디스크 커터의 마모 예측은 설계 및 시공 단계에서 비용과 공기 측면에서 매우 중요한 요소이다. 디스크 커터 마모 예측에 널리 사용되고 있는 방법으로는 노르웨이 NTNU 모델, CSM 모델과 Gehring 모델이 있지만, 시험의 정확도와 소요 시간의 측면에서 개선의 여지가 있었다. 이를 반영하여 NAT (New Abrasion Tester) 모델을 개발하였다(Farrokh and Kim, 2018). 제안된 NAT를 국내 ${\bigcirc}{\bigcirc}$현장에 적용하였고, 기존의 방법과 비교 검토를 수행하였다. 분석 결과 ${\bigcirc}{\bigcirc}$현장의 경우 기존 방법에 비해 NAT의 예측 결과가 커터 교체 현장 실측 데이터와 잘 맞는 것으로 나타났다. NAT 모델을 향후 더 많은 현장에 적용하여 모델의 신뢰도를 높일 예정이다.

• Elastomers and Composites
• /
• 제58권1호
• /
• pp.17-25
• /
• 2023

Abrasion tests of model tire tread compounds (NR and NR/BR blend compounds) were performed at different slip angles (1° and 7°) using a laboratory abrasion tester. The abrasion behavior was investigated by analyzing the worn surface and wear particles. The abrasion spacing formed on the specimen worn at the large slip angle of 7° was significantly narrower than that at the small slip angle of 1°, while the abrasion depth for the specimen worn at 7° was lower than that at 1°. The abrasion spacing and depth tended to be narrower and lower, respectively, as the BR content increased. The abrasion patterns were clearly visible on the outside of the specimen for the slip angle of 1° but not for 7°. The wear particles had a rough surface and there were numerous micro-bumps. It was found that the crosslink density affected the abrasion patterns and morphologies of the wear particles.

• Elastomers and Composites
• /
• 제54권4호
• /
• pp.313-320
• /
• 2019

A typical wear pattern was reported to resemble the fatigue crack growth behavior considering its mechanism, especially for amorphous rubbers such as styrene-butadiene rubber (SBR). In this study, the wear and crack growth rates were correlated using two separate experiments for carbon black and silica-reinforced selected rubber compounds. The wear rate was determined using a blade-type abrasion tester, where the frictional energy input during wearing was measured. The crack propagation rate was determined under different tearing energy inputs using a home-made fatigue tester, with a pure-shear test specimen containing pre-cracks. The rates of abrasion and crack propagation were plotted on a log-log scale as a function of frictional and tearing energies, respectively. Reasonable agreement was observed, indicating that the major mechanism of the abrasion pattern involved repeated crack propagation.

• Corrosion Science and Technology
• /
• 제7권6호
• /
• pp.362-369
• /
• 2008

The impact abrasion behavior of high manganese steel is investigated under three kinds of impact energy in acid hematite ore slurry by using a modified MLD-10 impact abrasion tester. Through the SEM observation of the worn surface and the optical metallographic analysis of the cross-sectional samples, the corrosive impact abrasion mechanisms of the steel under different impact energies are studied. In acid-hematite slurry, the variations of impact energies would result in synchronous transformation of the impact abrasion properties and mechanisms of the high manganese steel in the corrosive condition, as led different corrosive impact abrasion mechanism under different impact energies.

• 한국염색가공학회지
• /
• 제1권1호
• /
• pp.35-46
• /
• 1989

Experiments described in which cotton fabrics at different stages of chemical processing were abraded to different extents on a Stoll Abrasion Tester with three different abradants, namely, a worsted fabric, flax fabric and silicon carbide paper. The four different plain-weave cotton fabrics selected were 1) desized, 2) scoured and bleached, 3) mercerized, 4) resin-treated. The surface abrasive damages of treated fabrics were observed by SAM, and load-elongation percent retentions of abraded samples were measured by Instrong Tester. The result were as follows: 1. The maximum percent retention of load-elongation with three different abradants was exhibited by the scoured and bleached fabrics and the minimum by the resin finished fabric. 2. The electron micrographs of four different cotton fabrics abraded by flax, worsted fabric abradants for 900 rubs showed a large number of criss-crossing stray fibers in fabric structure. It may be the molecular adhesion for frictional resistance to be explained. 3. The electron micrographs of four different cotton fabrics abraded by silicone carbide abradants showed the form of busing or mashing fibers in fabric structure. The above might be on the basis of the ploughing theory.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.271-276
• /
• 1998

To apply the wear resistant steel plate for heavy duty vehicle, the wear characterisms of various kinds of commercial steel plates were invesigated by dry sand/rubber wheel tester which was tested under scratch abrasion mode. The wear tested pnaterials were boron steels which were manufactured by thereto machanical control process (TMCP) in order to achieve higher hardness. As the result of the test, wear resistance of steel plate increases with the hardness and carbon content. The wear loss of wear resistance steel plate (Hv440) is a half times than tinat of SWS490A (Hv160) steel plate in dry sand-rubber wheel test and the result in field test is similar to this dry sand/rubber wheel test result. Therefore, dry sand/rubber wheel tester can be used to predict the scratch abrasion life of the parts for heavy duty vehicle.