• Journal of the Korean Ceramic Society
• /
• v.46 no.3
• /
• pp.225-228
• /
• 2009

The processing and characterization of ceramic nanocomposites, which produce bulk nanostructures with attractive mechanical properties, have been emphasized and introduced at Prof. Mukherjee's Lab at UC Davis. The following subjects will be introduced in detail in Part II, III, and IV. In Part II, the paper will describe a three-phase alumina-based nanoceramic composite demonstrating superplasticity at a surprisingly lower temperature and higher strain rate. The next part will show that an alumina-carbon nanotube-niobium nanocomposite produced fracture toughness values that are three times higher than that of pure nanocrystalline alumina. It was possible to take advantage of both fiber-toughening and ductile-metal toughening in this investigation. In the fourth section, discussed will be a silicon-nitride/silicon-carbide nanocomposite, produced by pyrolysis of liquid polymer precursors, demonstrating one of the lowest creep rates reported so far in ceramics at the comparable temperature of $1400^{\circ}C$. This was first achieved by avoiding the oxynitride glass phase at the intergrain boundaries. One important factor in the processing of these nanocomposites was the use of the electrical field assisted sintering method. This allowed the sintering to be completed at significantly lower temperatures and during much shorter times. These improvements in mechanical properties will be discussed in the context of the results from the microstructural investigations.

• Korean Journal of Materials Research
• /
• v.27 no.11
• /
• pp.609-616
• /
• 2017

We investigated a Leidenfrost effect in the growth of ZnO nanostructures on silicon substrates by ultrasonic-assisted spray pyrolysis deposition(SPD). Structural and optical properties of the ZnO nanostructures grown by varying the growth parameters, such as substrate temperature, source concentration, and suction rate of the mist in the chambers, were investigated using field-emission scanning electron microscopy, X-ray diffraction, and photoluminescence spectrum analysis. Structural investigations of the ZnO nanostructures showed abnormal evolution of the morphologies with variation of the substrate temperatures. The shape of the ZnO nanostructures transformed from nanoplate, nanorod, nanopencil, and nanoprism shapes with increasing of the substrate temperature from 250 to $450^{\circ}C$; these shapes were significantly different from those seen for the conventional growth mechanisms in SPD. The observed growth behavior showed that a Leidenfrost effect dominantly affected the growth mechanism of the ZnO nanostructures.

• Computers and Concrete
• /
• v.21 no.4
• /
• pp.385-397
• /
• 2018

This study is focused on the investigation for similitude the requirements between prototype and scaled models to determine the structural behavior of concrete load bearing systems. The scaling concept has been utilized in many engineering branches, has been assisted to engineers and scientists for obtain the behavior of the prototype by using scaled model. The scaling can be done for two purposes, either scaling up or scaling down depending upon the application. Because, scaled down models are the experimentation on scaled models is cheaper than huge structures. These models also provide facilities for experimental work. Similarity relationships between systems are created either by field equations of the system or by dimensional analysis. Within this study, similarity relationships were obtained by both methods. The similarity relations obtained are applied to different load bearing systems and it is determined that the similarity relation is a general expression. In this study, as an example, column, frame, cantilever beam and simple beam are chosen and 1/2, 1/5 and 1/10 scales are applied. The results are compared with the analytical results which are obtained by creating of the finite element models with SAP2000 software of different scaled load bearing systems. The analysis results of all systems are examined and it is determined that the scale factors are constant depending on the scale types for different load bearing systems.

• Journal of the Korean institute of surface engineering
• /
• v.13 no.4
• /
• pp.221-227
• /
• 1980

When anodizing the Al in the acid electrolyte, it is well known that the parallel pores grow continuously perpendicular to the surface. This fact can be used for the manufacturing of the porous membrane, if thc pores pass through the anodized foil. Anodizing both surfaces of the Al-foil spontaneously in 20$^{\circ}C$, 2% oxalic acid under tile potentiostatic condition, it is found that the harrier layer remaining in the midst of the foil finally disappears and thc pores pass through the foil. And examined the porous structure change when the voltage is changed during the anodizing treatment. From the result, it is revealed that the new pores and cell grow, adjusting themselves to the final voltage. The characteristic of the porous membrane is greatly dependent upon the diameter of the pore and the cell. So studied the relationship between the voltage and the diameter of the pore and the cell quantitatively with the aid of field-assisted dissolution concept. And derived the following two equation, Pi = 8.32Vi, Ci = 26.80Vi. These equations are in good accord with the experimental data above 30V, but do not accord nuder 30V.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.252.2-252.2
• /
• 2013

ZnO nanostructures have a lot of interest for decades due to its varied applications such as light-emitting devices, power generators, solar cells, and sensing devices etc. To get the high performance of these devices, the factors of nanostructure geometry, spacing, and alignment are important. So, Patterning of vertically- aligned ZnO nanowires are currently attractive. However, many of ZnO nanowire or nanorod fabrication methods are needs high temperature, such vapor phase transport process, metal-organic chemical vapor deposition (MOCVD), metal-organic vapor phase epitaxy, thermal evaporation, pulse laser deposition and thermal chemical vapor deposition. While hydrothermal process has great advantages-low temperature (less than $100^{\circ}C$), simple steps, short time consuming, without catalyst, and relatively ease to control than as mentioned various methods. In this work, we investigate the dependence of ZnO nanowire alignment and morphology on si substrate using of nanosphere template with various precursor concentration and components via hydrothermal process. The brief experimental scheme is as follow. First synthesized ZnO seed solution was spun coated on to cleaned Si substrate, and then annealed $350^{\circ}C$ for 1h in the furnace. Second, 200nm sized close-packed nanospheres were formed on the seed layer-coated substrate by using of gas-liquid-solid interfacial self-assembly method and drying in vaccum desicator for about a day to enhance the adhesion between seed layer and nanospheres. After that, zinc oxide nanowires were synthesized using a low temperature hydrothermal method based on alkali solution. The specimens were immersed upside down in the autoclave bath to prevent some precipitates which formed and covered on the surface. The hydrothermal conditions such as growth temperature, growth time, solution concentration, and additives are variously performed to optimize the morphologies of nanowire. To characterize the crystal structure of seed layer and nanowires, morphology, and optical properties, X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Raman spectroscopy, and photoluminescence (PL) studies were investigated.

• Horticultural Science & Technology
• /
• v.28 no.6
• /
• pp.1014-1024
• /
• 2010

Pepper ($Capsicum$ spp.) anthracnose caused by $Colletotrichum$ $acutatum$ is a destructive disease susceptible to areas where chili peppers are grown. $Capsicum$ $baccatum$ var. $pendulum$ (Cbp) is resistant to anthracnose and has actively been used for interspecific hybridization for the introgression of resistance gene(s) into cultivated chili peppers. The goals of this study were to determine the inheritance of resistance to anthracnose within $Capsicum$ $baccatum$ and to map quantitative trait loci (QTLs) for the anthracnose resistance. A genetic mapping population consisting of 126 $F_2$ plants derived from a cross between $Capsicum$ $baccatum$ var. $pendulum$ (resistant) and $Capsicum$ $baccatum$ 'Golden-aji' (susceptible) was used for linkage mapping. The linkage map was constructed with 52 SSRs, 175 AFLPs, and 100 SRAPs covering 1,896cM, with an average interval marker distance of 4.0cM. Based on this map, the number, location, and effect of QTLs for anthracnose resistance were studied using plants inoculated in the laboratory and field. A total of 19 quantitative trait loci (2 major QTLs and 16 minor QTLs) were detected. Two QTLs ($An8.1$, $An9.1$) showed 16.4% phenotypic variations for anthracnose resistance after wounding inoculation. In addition, five minor QTL loci ($An7.3$, $An7.4$, $An4.1$, $An3.1$, $An3.2$) showed a total of 60.73% phenotypic variations of anthracnose resistance in the field test. Several significant QTLs were also detected and their reproducibility was confirmed under different inoculation conditions. These QTLs are now being confirmed with different breeding populations. Markers tightly linked to the QTLs that are reliable under different environmental conditions will help to determine the success of marker-assisted selection for anthracnose -resistant breeding programs in chili pepper.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06a
• /
• pp.5-18
• /
• 1996

The solid state cesium ion source os alumino-silicate based zeolite which contains cerium. The material is an ionic conductor. Cesiums are stably stored in the material and one can extract the cesiums by applying electric field across the electrolyte. Cesium ion bombardment has the unique property of producing high negative ion yield. This ion source is used as the primary source for the production of a negative ion without any gas discharge or the need for a carrier gas. The deposition of materials as an ionic species in the energy range of 1.0 to 300eV is recently recognized as a very promising new thin film technique. This energetic non-thermal equilibrium deposition process produces films by “Kinetic Bonding / Energetic Condensation" mechansim not governed by the common place thermo-mechanical reaction. Under these highly non-equilibrium conditions meta-stable materials are realized and the negative ion is considered to be an optimum paeticle or tool for the purpose. This process differs fundamentally from the conventional ion beam assisted deposition (IBAD) technique such that the ion beam energy transfer to the deposition process is directly coupled the process. Since cesium ion beam sputter deposition process is forming materials with high kinetic energy of metal ion beams, the process provider following unique advantages:(1) to synthesize non thermal-equilibrium materials, (2) to form materials at lower processing temperature than used for conventional chemical of physical vapor deposition, (3) to deposit very uniform, dense, and good adhesive films (4) to make higher doposition rate, (5) to control the ion flux and ion energy independently. Solid state cesium ion beam sputter deposition system has been developed. This source is capable of producing variety of metal ion beams such as C, Si, W, Ta, Mo, Al, Au, Ag, Cr etc. Using this deposition system, several researches have been performed. (1) To produce superior quality amorphous diamond films (2) to produce carbon nitirde hard coatings(Carbon nitride is a new material whose hardness is comparable to the diamond and also has a very high thermal stability.) (3) to produce cesiated amorphous diamond thin film coated Si surface exhibiting negative electron affinity characteristics. In this presentation, the principles of solid state cesium ion beam sputter deposition and several applications of negative metal ion source will be introduced.

• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.3
• /
• pp.451-455
• /
• 2015

The buffalo is an important livestock resource in several countries of South Asia and the Mediterranean regions. However, reproductive efficiency is compromised due to known problems of biological and management origins, such as lack of animal selection and poor nutrition. Under optimal conditions puberty is attained at 15 to 18 months in river buffalo, 21 to 24 months in swamp buffalo and is influenced by genotype, nutrition, management and climate. However, under field conditions these values deteriorate up to a significant extant. To improve reproductive efficiency, several protocols of oestrus and ovulation synchronization have been adopted from their use in commercial cattle production. These protocols yield encouraging pregnancy rates of (30% to 50%), which are comparable to those achieved in buffaloes bred at natural oestrus. The use of sexed semen in buffalo heifers also showed promising pregnancy rates (50%) when compared with conventional non-sexed semen. Assisted reproductive technologies have been transferred and adapted to buffalo but the efficiency of these technologies are low. However, these latest technologies offer the opportunity to accelerate the genetic gain in the buffalo industry after improving the technology and reducing its cost. Most buffaloes are kept under the small holder farming system in developing countries. Hence, future research should focus on simple, adoptable and impact-oriented approaches which identify the factors determining low fertility and oestrus behaviour in this species. Furthermore, role of kisspeptin needs to be explored in buffalo.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.2
• /
• pp.49-52
• /
• 2006

Periodic electric field assisted poling low loss (${\sim}0.1dB/cm$) single-mode Ti-diffused waveguides in $LiNbO_3$ has been achieved using a periodically patterned electrode on the +Z surface of Ti : $LiNbO_3$ crystal and homogeneous LiCl solution. Using selective chemical etching, we confirmed the periodic (${\sim}16{\mu}m$) domain inverted structure and measured SH (second harmonic) properties of fabricated periodically poled Ti : $LiNbO_3$ waveguides.

• Korean Journal of Materials Research
• /
• v.18 no.11
• /
• pp.583-591
• /
• 2008

In this study, two series of CNT/$TiO_2$ electrodes were prepared. The decrease of surface area compared with that of the pristine carbon nanotubes (CNTs) indicated the blocking of micropores on the surface of the CNTs; was further supported by scanning electron microscopy (SEM) and field emission SEM (FE-SEM) observations. The X-ray diffraction (XRD) results showed that the CNT/$TiO_2$ composites contained a mix of anatase and rutile forms of $TiO_2$ particles when the precursor was $TiO_2$ powder, whereas when the precursor was Ti ($OC_4H_7$) (TNB), the composites contained only the typical single and clear anatase $TiO_2$ particles. The energy dispersive X-ray spectroscopy (EDX) spectra showed the presence of C, O and Ti peaks for all samples. It was found that catalytic decomposition of methylene blue (MB) solution could be attributed to synthetic effects between the $TiO_2$ photocatalysis and electro-assisted CNTs network, and that photoelectrocatalytic oxidation increased with an increase of CNT composition. It was also found that the photoelectrocatalytic oxidation efficiency for MB is higher than that of photocatalytic oxidation. Moreover, the CNT/$TiO_2$ composites catalyst prepared by the impregnation method demonstrates higher photoelectrocatalytic activity than the mechanical mixture with the same CNT content.