• 한국미생물·생명공학회지
• /
• 제36권1호
• /
• pp.61-66
• /
• 2008

Flask 배양으로 기본 유청 배지MSM를 배지로 하고 첨가한 각 탄소원의 PS-7생산 효과를 살펴보면 fructose, glucose와 sucrose의 첨가가 PS-7의 생산을 다른 당에 비해 향상시킴을 알 수 있었다. 그러나 galactose의 경우 첨가량이 증가될수록 오히려 PS-7의 생산량이 감소되는 경향을 나타내었다. 여러 가지 배양 변수를 고려한 결과 glucose씨 첨가가 최적임을 확인하였다. 5L 발효조에 의한 PS-7 생산의 경우 유청과 glucose를 함께 첨가한 것이 유청과 glucose만을 배지의 탄소원으로 사용했을 때 보다 PS-7의 생산량이 월등히 향상되는 것을 알 수 있었으며, 유청 1%와 glucose 1%배지의 경우 PS-7생산량이 3 g/L를 생산하였다. 유청 1%와 glucose 2%배지의 경우 4 g/L의 PS-7의 생산하였으나 잔당량이 $30{\sim}40%$가 남아 생산효율(yield)면에서는 떨어짐을 알 수 있었다. 배지내 Glucose농도 변화에 따른 점성(viscosity)의 변화는 PS-7의 생산량의 변화와 비슷한 패턴을 보이지만 분자량 증대에 따른 점도의 증가는 훨씬 높게 나타났다. 본 실험의 결과 일반적으로 C/N ratio가 다당류인 PS-7생산에 중요한 역할을 하고 있으며, 유청 1%+glucose 1% 배지를 사용할 때 높은 점도와 수율의 PS-7을 얻을 수 있는 최적 배지임을 알 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제42권4호
• /
• pp.428-438
• /
• 2014

최근 다양한 언론매체 및 국내외 연구논문들을 통해 꽃송이버섯의 기능성이 부각되고 있다. 이에 꽃송이버섯의 농가 대량재배 일반화를 위하여 최적톱밥 입자크기 및 ${\beta}$-glucan 함량이 높은 재배법 연구를 수행한 결과 T7 (1~2 mm 25%, 2~4 mm 50%, 4 mm 이상 25%) 배지와 같이 입자크기가 일정비율로 혼합된 배지에서 $11.5{\pm}1.0$ cm/44 days로 비교적 우수한 균사생장을 보였으며 자실체생산 역시 대조구보다 높은 $142.9{\pm}17.7g$의 생중량으로 상품성이 있는 꽃부분이 85%의 비율을 차지하였다. 배지조성 조건에 따른 ${\beta}$-glucan 함량은 모든 자실체에서 꽃부분에 비해 기부가 1.4~2.4배의 높은 함량을 보였고 이 중 이스트 300 ppm이 첨가된 PCF300 (미송 + 옥수수분말 + 소맥분 + 이스트 300 ppm) 배지의 꽃송이버섯 기부가 59.5%로 가장 높은 ${\beta}$-glucan 함량을 나타냈다. 그러나 꽃부분에서는 비교적 낮은 33.0%의 함량을 보여 꽃부분의 ${\beta}$-glucan 함량을 높일 수 있는 추가적인 연구가 필요할 것으로 사료된다. 따라서 본 연구결과를 토대로 꽃송이버섯 재배시 T7조건인 1~2 mm 미송톱밥 25%, 2~4 mm 미송톱밥 50%, 4 mm 이상 미송톱밥 25%의 비율로 톱밥입자 크기를 조절한후 옥수수분말과 소맥분을 첨가하여 배지조제후 이스트 300 ppm첨가하면 ${\beta}$-glucan 함량이 높은 꽃송이버섯 생산이 가능할 것으로 사료된다.

• Journal of Chest Surgery
• /
• 제31권12호
• /
• pp.1172-1182
• /
• 1998

배경: 기계적 보철판막을 사용한 환자에서의 항응혈제 치료의 목표는 혈전전색의 효과적 예방과 출혈의 안전한 방지에 있다. 대상 및 방법: 1984년부터 1995년까지 쎈트쥬드판막으로 심장판막을 치환한 209례(승모판치환 122, 대동맥판치환 48, 중복판막치환 48)의 환자에서 실제로 수행된 항응혈제 수준과 임상적 결과를 분석하였다. 쿠마딘으로 항응혈제 치료를 개시하고 원칙적으로 월 1회의 외래 내원하여 검사와 프로트롬빈시간 측정으로 국제정상화비(International Normalized Ratio : INR)를 낮은 강도의 치료적 목표범위 1.5∼2.5 내에 조정하였다. 결과: 총 항응혈제 추적기간은 1082.0환자년(평균 62.1개월)이고 프로트롬빈시간 검사는 총 10,205회였다. 치환판막군간에 유의한 차이없이 총 측정수의 65%에서의 INR값만이 목표범위이내에 있었다. 각 환자에서 추적기간중 시행한 프로트롬빈시간 측정의 70%이상이 목표범위에 포함되었던 환자는 77례(37%)에 불과하였다. 환자의 57%에서 본 심방세동이 있던 환자에서의 INR수준은 정상동률이던 환자에서의 수준보다 분명하게 높았다(p<0.001). 혈전전색증은 15례가 경험하여 연간빈도가 1.265%/환자년(승모판치환 1.412%/환자년, 대동맥판치환 0.462%/환자년, 중복판막치환 1.531%/환자년)이고 출혈은 4례로 0.337%/환자년의 연간빈도를 보였다(승모판치환 0.424%/환자년, 대동맥판치환은 없고, 중복판막치환 0.383%/환자년). 빈번하거나 장기간의 프로트롬빈시간 측정의 탈락은 혈전전색합병증에 크게 연관된 주요 위험요소였다(대응비 1.99). 각 환자에서의 INR값이 목표범위내에 포함된 비율이 60%에 미달하였던 환자에서는 혈전전색합병증과 전색과 출혈의 종합합병증의 발생률이 높아 명확하게 큰 위험요소였다(각각 p<0.004 및 p<0.002). 결론: 낮은 강도의 치료적 목표범위가 대동맥판치환이고 정상동률인 환자에서는 적절한 수준인 듯 하다. 그러나 승모판을 치환한 환자에서 특히 심방세동을 동반할 때에는 혈전전색합병증을 효과적으로 예방하기에 충분한 실제적 항응혈제 수준을 성취하려면 보다 높은 INR의 목표범위가 필요할 듯 하며 INR 2.0∼3.0을 치료적 목표범위로 하는 임상적 결과의 축적이 필요하다. 환자가 합병증에 노출되는 기회와 기간을 최소화하려면 주기적 외래방문을 지키고 쿠마딘 복용을 빼지 않도록 계속 지도하여 환자의 순응도를 높이는 동시에 INR값을 엄격하게 적정범위 내에 일관되게 유지하여야 한다. 특히 합병증의 위험요소가 있는 환자와 INR값의 변동폭이 지나치게 넓은 환자에서는 빈번한 항응혈제 수준의 감시가 필요하다.

• 미생물학회지
• /
• 제45권3호
• /
• pp.286-290
• /
• 2009

조류인플루엔자 바이러스 mRNA의 전사는 감염 동안에 시간적으로 조절되어진다. 감염 후 세포 내에서 증식된 바이러스가 방출되어 세포를 다시 감염하게 되면 전사 수준 분석에 오차가 발생할 수 있으므로 바이러스가 방출 되기 이전에 전사 수준의 측정이 이루어져야 한다. 본 연구에서는 조류인플루엔자 H9N2를 감염시킨 닭의 섬유아세포주 UMNSAH/DF-1에서 바이러스 감염 후 증식된 바이러스의 방출까지의 시간을 측정하기 위하여 배양액 중에 방출되는 바이러스 RNA 게놈 수준을 semi-quantitative RT-PCR에 의해 측정하였다. 배양액 중의 바이러스 RNA 게놈의 분리 과정에서 발생할 수 있는 RNA 회수율의 오차를 보정하기 위해 mouse의 전체 RNA를 배양액 시료에 넣어서 바이러스 RNA 분리에 carrier로 사용하고 그 속에 포함된 mouse의 GAPDH를 RNA를 역전사 반응 및 PCR의 내부 대조 RNA로 사용하였다. 그 결과 감염 후 방출까지 16~20시간이 소요됨을 알 수 있었다. 따라서 감염 후 12시간 후에 세포 내에서 합성된 8종의 전사체의 수준을 측정하였다. 8종의 mRNA 중 PA를 제외한 7종의 mRNA (HA, NA, PB1, PB2, NP, M, NS를 암호화하는 mRNA)는 뚜렷한 증폭 band를 보였으며, 이것은 이들이 전사활성 측정에 사용될 수 있는 것으로 나타났다. 이상과 같은 전사수준의 측정 방법은 조류인플루엔자 바이러스의 RNA polymerase를 표적으로 한 항바이러스제의 검색에 사용할 수 있을 것으로 보인다.

• 한국토양비료학회지
• /
• 제44권5호
• /
• pp.717-721
• /
• 2011

시설재배지는 주로 논토양에 설치되는데 밭작물을 재배하기 때문에 재배적지를 잘 선정하는 것이 무엇보다 중요하다. 시설재배지를 연작할 경우 염농도 (EC)의 상승, 양분불균형, 병충해 증가로 농산물의 품질이나 수량이 떨어지기 때문에 종합적인 토양관리를 해야 할 필요성이 있다. 이러한 재배지에서 오이의 수량 확보와 고품질 농산물을 생산하기 위해서는 종합적인 토양개량이 필요하다. 고품질 오이생산기술을 개발하기 위하여 적지선정, 토양비옥도, 환경관리, 병충해경감, 비료흡수의 경시적 변화 등을 검토하였고, 오이의 뿌리조사 및 수량과 경제성 분석을 수행하여 얻은 결과는 다음과 같다. 시설오이재배적지는 하성평탄지 및 곡간지이고, 배수는 약간양호 내지 약간불량이며, 토성은 사양질, 유효토심은 100 cm내외, 침수로 부터는 안전한 지대이어야 하고, 햇빛이 잘 들고 지하수가 풍부한 지역이 좋다. 시설 내 환경관리 중 온도는 3단계로 조절하는데 주간은 $22{\sim}28^{\circ}C$, 밤 12시까지는 $14{\sim}15^{\circ}C$, 밤 12시부터 해뜨기 직전 $10{\sim}12^{\circ}C$로 유지하며, 수분관리는 영양생장기에는 0~15%로 낮게 유지하고, 생식생장기에는 15~20%로 조절하여야 다수확과 고품질의 오이를 생산할 수 있다. 시설 연작장해지의 염농도 저감은 옥수수와 같은 청예작물을 재배하고, 뿌리혹선충방제는 토양열소독으로 방제하면 고품질의 오이를 재배할 수 있다. 시설오이수량 및 경제적분석결과 종합개량처리구는 158.0 Mg이고 연작장해지는 $140.3kg\;Mg^{-1}$ 이었다. 소득은 종합개량구가 215,676 천원, 연작장해지는 131,649 천원 $ha^{-1}$으로 소득율이 각각 51.8, 38.4% 이었다.

• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• Radiation Oncology Journal
• /
• 제25권4호
• /
• pp.242-248
• /
• 2007

목적: 마우스 모델에서 cisplatin과 방사선조사로 구내염을 유발시킨 후 재조합 표피성장인자 (recombinant human epidermal growth factor, rhEGF)을 처치하여 그 효과를 알아보고자 하였다. 대상 및 방법: 마우스 24마리를 대상으로 정상대조군 8마리와 실험군은 각각 rhEGF 처치군과 미처치군으로 8마리씩 분류하였으며 실험군은 10 mg/kg의 cisplatin을 방사선조사 첫날 동시에 1회 복강 내 투여하였고, 방사선조사는 5일간 1회 5 Gy씩, 5일간 25 Gy를 조사하였다. RhEGF 처치군은 방사선조사 2일 전부터 2일간 1 mg/kg의 rhEGF를 피하주사하였으며 방사선조사3일째부터 3일간 1 mg/kg를 피하주사하여 총 5 mg/kg의 rhEGF를 투여하였다. 마우스의 체중변화, 먹이섭취 및 조직학적 변화를 평가하였다. 결 과: 마우스 체중변화는 rhEG F처치군이 실험 3일째부터 5일간 rhEGF 미처치군과 비교하여 통계적으로 유의한 체중의 차이를 관찰할 수 있었다. 먹이섭취는 실험군(rhEGF 처치군과 미처치군)에서 실험 5일째까지 감소하였다가 13일째부터 먹이섭취의 증가를 보여주었다. Cisplatin과 방사선조사 후 7일째의 조직학적 검사에서는 rhEGF 처치군에서 마우스의 점막 표피층의 변성이 관찰되었으나 rhEGF 미처치군에서는 점막층의 염증 반응이 관찰되었다. 결 론: Cisplatin과 방사선 조사로 마우스에서 발생한 구내염에서 rhEGF를 투여한 경우 체중 변화와 먹이섭취의 유의한 개선을 관찰하였으며 조직학적 검사에서 점막 손상의 회복을 확인하였다. 향후 임상적으로 rhEGF가 항암화학요법과 방사선치료로 인한 구내염을 줄일 수 있는 가능성을 확인하였다.값은 11개월이었고 2년, 3년 생존율은 31.5%, 15.8%였다. 결 론: 2기 췌장암 환자들은 국소 재발 및 원격 전이의 가능성이 높은 고위험군으로 국소 제어율 및 전체 생존율의 향상을 위해서 수술 후 효과적인 방사선치료의 적극적인 시행 및 이후의 보조적인 전신 항암화학요법을 권고하여 시행하는 것이 바람직하다. 평가 검사는 모두 제조사의 시험지침서에 부합하였다. 결론적으로, 이는 본 GE $Advance^{TM}$ PET 시스템이 임상에의 적용에 적합함을 보여주었다.mens사의 상용 분석 프로그램에는 해당 기능이 없어 계산값의 비교를 통한 검증은 수행하지 못하였고, 수화(hydration)와 탈수(dehydration) 각각의 조건에 따른 신장기능 분석에 적용하였을 때, 판별 기준이 되는 유의미한 값을 산출하여 타당성 검증을 대신하였다. 결론: 이 연구에서 개발한 핵의학 영상의 정량적 분석을 통한 신장기능 분석 프로그램을 사용하여 신장 기능을 분석한 결과, 타당성 있는 결과를 도출하여 그 유용성을 입증하였다. 이 개발 프로그램은 좀 더 다양한 임상응용 목적의 분석기능을 사용자가 직접 개발, 추가하기가 용이하여 기존 상용 프로그램보다 연구적 활용범위가 크다고 사료된다.2.2{\pm}0.4\;(1.6{\sim}3.2){\mu}g/ml$와 $1.4{\pm}0.2\;(0.8{\sim}1.6){\mu}g/ml$로서(p=0.16), 표준균주 3종 모두에서 Infecton의 MBC 또한 ciprofloxacin에 비해 $2{\sim}4$배가 높았다. 결론: Tc-99m Infecton은 ciprofloxacin 보다는 약하였지만 표준균주에 대해 생체외 항균력을 보였다.를

• 헤리티지:역사와 과학
• /
• 제44권4호
• /
• pp.172-205
• /
• 2011

본 연구는 종합적인 현황 조사 분석을 통해 국내 돌바둑판의 위치 및 형태 그리고 입지 유형을 파악하는 한편 주변 경물과 각자 그리고 인근의 전래지명과의 관련성 분석과 해석을 통해 암각바둑판의 본질적 특성 및 장소적 의미 그리고 문화재로서의 가치 등을 파악하고자 하였다. 바둑판에 나타난 '네모난 바둑판과 둥근 바둑돌'의 천원지방적(天圓地方的) 형상, 흑백 바둑돌로 표상되는 음양조화 그리고 하늘 회전을 표현한 361로 등은 '우주적 질서가 투사(投射)된 상징체'이다. 또한 영원성을 바탕으로 바둑 삼매경에 빠진 '귤중지락(橘中之樂)'과 '상산사호(商山四皓)' 그리고 '난가(爛柯)' 모티프는 속세를 벗어난 망우청락(忘憂淸樂)의 '위기선미(圍棋仙味)'를 통해 '인생과 자연'의 관계를 시공간적으로 일치하고자 했던 천인합일의 표상이자 우미와 소요를 추구한 고아한 풍류였다. 본 연구를 통해 확인된 돌바둑판은 총본 연구는 종합적인 현황 조사 분석을 통해 국내 돌바둑판의 위치 및 형태 그리고 입지 유형을 파악하는 한편 주변 경물과 각자 그리고 인근의 전래지명과의 관련성 분석과 해석을 통해 암각바둑판의 본질적 특성 및 장소적 의미 그리고 문화재로서의 가치 등을 파악하고자 하였다. 바둑판에 나타난 '네모난 바둑판과 둥근 바둑돌'의 천원지방적(天圓地方的) 형상, 흑백 바둑돌로 표상되는 음양조화 그리고 하늘 회전을 표현한 361로 등은 '우주적 질서가 투사(投射)된 상징체'이다. 또한 영원성을 바탕으로 바둑 삼매경에 빠진 '귤중지락(橘中之樂)'과 '상산사호(商山四皓)' 그리고 '난가(爛柯)' 모티프는 속세를 벗어난 망우청락(忘憂淸樂)의 '위기선미(圍棋仙味)'를 통해 '인생과 자연'의 관계를 시공간적으로 일치하고자 했던 천인합일의 표상이자 우미와 소요를 추구한 고아한 풍류였다. 본 연구를 통해 확인된 돌바둑판은 총 18개로 이중 강진 월남사지 돌바둑판, 양산 소한정 돌바둑판, 반룡대 돌바둑판 등 3개소(16.1%)는 이동이 가능한 석국으로 분류된 반면 방학동 돌바둑판을 비롯한 15개소(83.9%)는 자연 암반에 새긴, 원래 장소를 이탈하지 않은 암각바둑판으로 밝혀졌다. 돌바둑판의 입지조건을 유형화한 결과, 계류형 15개소(83.9%), 암봉형 3개소(16.1%)로 나타났으며 가장 높은 곳에 위치한 것은 소백산 신선봉 암각바둑판(1,389m)이었다. 총 15개 돌바둑판은 모두 500m 이하의 저산지에 입지하고 있는 것으로 보아 바둑판이 새겨진 입지는 속세와 멀지 않은 생활권의 일부였으며 모두 경관성이 탁월한 계곡 및 산봉에 입지하였다. 돌바둑판은 옛 선비들의 풍류와 밀접한 관련이 있는 것으로 추찰되는바 특히 암각바둑판은 천인합일(天人合一)의 조화를 추구하며 명산대천(名山大川)을 찾아 함께 노니는 풍류도의 정신을 전승한 것으로 파악된다. 즉 궁극적으로 바둑의 전통적인 상징성인 '은일의 매개체이자 자연귀의의 도에 다다를 수 있는 선비문화의 정수'인 동시에 유선적 취향의 도구로서 자리매김 하였음을 알 수 있다. 특징적으로 암각바둑판이 새겨진 단양 소백산 신선봉을 비롯하여 괴산 선국암, 무주 사선암, 장수 신선바위 등은 신선과 관련된 지명의 일체감이 매우 높은 것으로 미루어 보아 '신선' 바위와 암각바둑판이야말로 선계에 대한 숭배와 동경의 소통방식이 가장 함축적으로 표현된 경관대상이자 조망처로 판단된다. 한편 암각바둑판이 입지하는 장소의 입지유형 등 물리적 환경과 팔경 및 동천구곡의 설정 여부, 유학자 등의 관련 여부를 중심으로 한 '인간활동' 그리고 '상산사호' 모티프 및 '난가고사' 상징의미 등 3가지를 '장소정체성 판단을 위한 해석 틀'을 기준으로 하여 고찰한 결과, 암각바둑판 주변에 각자 되어있는 동천, 동문 등의 모티프는 주자학적 '구곡팔경'의 개념 보다는 선취적 '선유동천' 개념의 공간성 모색이 필요한 것으로 보인다. 전반적으로 계류형 암각바둑판이 조성된 공간은 유가의 은둔지향적 공간이나 선도적 은일지향적 공간으로 시대추이에 따라 습합되어 온 것으로 판단되며 산봉형의 암각바둑판은 별도로 신선 강림의 숭엄지향성이 장소정체성 지배의 중요 요인으로 평가된다. 아울러 암각바둑판이 조성된 곳을 포함하여 그 주변은 동천구곡이나 팔경의 일부로 널리 알려진 승경의 요처임이 확인되었다. 또한 선비 및 사대부 계층이 주체인 주변 각자들 중에도 신선 관련 표현어가 다수 발견됨에 따라 바둑판 조영의식의 이면에는 신선경 동경을 바탕으로 한 선도적 취향이 강하게 작용하고 있음이 확인되었다. 이와 같은 결과를 총합할 때 암각바둑판은 조선조 선비들의 은일과 운둔을 통한 자연경영의 문화 현상이 집약적으로 함축된 유산이자 전래 승경의 요처로, 명승과 같은 자연문화재로서의 가치가 탁월한 대상임이 확인되었다. 현재 남한내 17개의 돌바둑판 중에서 소백산 신선봉 암각바둑판을 비롯하여 방학동 암각바둑판, 충주 사로암 암각바둑판, 무주 사선암 암각바둑판, 양산 어곡동 반룡대 석국 등은 세월의 풍파와 사람들의 접촉으로 마모되면서 바위가 깨어지거나 바둑판 줄이 희미해지고 있다. 또한 언양 반구대 집청정 암각바둑판은 토사 매몰로 그 형체를 확인하기 어려운 상태이다. 암각바둑판은 자연과 바람의 흐름을 그대로 투영한 예술적, 문화재적 가치가 탁월한 조형물이자 선인들의 자연 사랑의 마음과 선계동경의 문화가 만나 이루어진 문화유적으로, 이에 대한 국내 분포 현황에 대한 체계적인 정밀조사와 보존관리가 시급하다고 사료된다. 18개로 이중 강진 월남사지 돌바둑판, 양산 소한정 돌바둑판, 반룡대 돌바둑판 등 3개소(16.1%)는 이동이 가능한 석국으로 분류된 반면 방학동 돌바둑판을 비롯한 15개소(83.9%)는 자연 암반에 새긴, 원래 장소를 이탈하지 않은 암각바둑판으로 밝혀졌다. 돌바둑판의 입지조건을 유형화한 결과, 계류형 15개소(83.9%), 암봉형 3개소(16.1%)로 나타났으며 가장 높은 곳에 위치한 것은 소백산 신선봉 암각바둑판(1,389m)이었다. 총 15개 돌바둑판은 모두 500m 이하의 저산지에 입지하고 있는 것으로 보아 바둑판이 새겨진 입지는 속세와 멀지 않은 생활권의 일부였으며 모두 경관성이 탁월한 계곡 및 산봉에 입지하였다. 돌바둑판은 옛 선비들의 풍류와 밀접한 관련이 있는 것으로 추찰되는바 특히 암각바둑판은 천인합일(天人合一)의 조화를 추구하며 명산대천(名山大川)을 찾아 함께 노니는 풍류도의 정신을 전승한 것으로 파악된다. 즉 궁극적으로 바둑의 전통적인 상징성인 '은일의 매개체이자 자연귀의의 도에 다다를 수 있는 선비문화의 정수'인 동시에 유선적 취향의 도구로서 자리매김 하였음을 알 수 있다. 특징적으로 암각바둑판이 새겨진 단양 소백산 신선봉을 비롯하여 괴산 선국암, 무주 사선암, 장수 신선바위 등은 신선과 관련된 지명의 일체감이 매우 높은 것으로 미루어 보아 '신선' 바위와 암각바둑판이야말로 선계에 대한 숭배와 동경의 소통방식이 가장 함축적으로 표현된 경관대상이자 조망처로 판단된다. 한편 암각바둑판이 입지하는 장소의 입지유형 등 물리적 환경과 팔경 및 동천구곡의 설정 여부, 유학자 등의 관련 여부를 중심으로 한 '인간활동' 그리고 '상산사호' 모티프 및 '난가고사' 상징의미 등 3가지를 '장소정체성 판단을 위한 해석 틀'을 기준으로 하여 고찰한 결과, 암각바둑판 주변에 각자 되어있는 동천, 동문 등의 모티프는 주자학적 '구곡팔경'의 개념 보다는 선취적 '선유동천' 개념의 공간성 모색이 필요한 것으로 보인다. 전반적으로 계류형 암각바둑판이 조성된 공간은 유가의 은둔지향적 공간이나 선도적 은일지향적 공간으로 시대추이에 따라 습합되어 온 것으로 판단되며 산봉형의 암각바둑판은 별도로 신선 강림의 숭엄지향성이 장소정체성 지배의 중요 요인으로 평가된다. 아울러 암각바둑판이 조성된 곳을 포함하여 그 주변은 동천구곡이나 팔경의 일부로 널리 알려진 승경의 요처임이 확인되었다. 또한 선비 및 사대부 계층이 주체인 주변 각자들 중에도 신선 관련 표현어가 다수 발견됨에 따라 바둑판 조영의식의 이면에는 신선경 동경을 바탕으로 한 선도적 취향이 강하게 작용하고 있음이 확인되었다. 이와 같은 결과를 총합할 때 암각바둑판은 조선조 선비들의 은일과 운둔을 통한 자연경영의 문화 현상이 집약적으로 함축된 유산이자 전래 승경의 요처로, 명승과 같은 자연문화재로서의 가치가 탁월한 대상임이 확인되었다. 현재 남한내 17개의 돌바둑판 중에서 소백산 신선봉 암각바둑판을 비롯하여 방학동 암각바둑판, 충주 사로암 암각바둑판, 무주 사선암 암각바둑판, 양산 어곡동 반룡대 석국 등은 세월의 풍파와 사람들의 접촉으로 마모되면서 바위가 깨어지거나 바둑판 줄이 희미해지고 있다. 또한 언양 반구대 집청정 암각바둑판은 토사 매몰로 그 형체를 확인하기 어려운 상태이다. 암각바둑판은 자연과 바람의 흐름을 그대로 투영한 예술적, 문화재적 가치가 탁월한 조형물이자 선인들의 자연 사랑의 마음과 선계동경의 문화가 만나 이루어진 문화유적으로, 이에 대한 국내 분포 현황에 대한 체계적인 정밀조사와 보존관리가 시급하다고 사료된다.