• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.618-621
• /
• 2004

Compressors in Large Multi-room air conditioning system are often driven by gas heat pumps. The advantages of GHP are their high level of heating performance and low cost because they use the LNG fuel to drive engine. We developed engine control system. The developed system controls engine speed based on proportional, integral and derivative (PID) method. This controller is designed to eliminate the need for continuous operator attention on engine revolution control. The control system includes 4 spark coil drivers, fuel drivers and relay drivers to make engine's operating more stable. The experiments of control engine revolution of this system are based on the various load conditions.

• The Journal of Korea Robotics Society
• /
• v.19 no.1
• /
• pp.65-70
• /
• 2024

Tool wear is considered an important issue in manufacturing and engineering, as worn tools can negatively impact productivity and product quality. Given that the wear status of tools plays a decisive role in the production process, measuring tool wear is a key task. Consequently, there is significant attention in manufacturing fields on the precise measurement of tool wear. Current domestic methods for measuring wear are limited in terms of speed and efficiency, with traditional methods being time-consuming and reliant on subjective evaluation. To address these issues, we developed a measurement module implementing the DeepContour algorithm, which uses image processing technology for rapid measurement and evaluation of tool wear. This algorithm accurately extracts the tool's outline, assesses its condition, determines the degree of wear, and proves more efficient than existing, subjective, and time-consuming methods. The main objective of this paper is to design and apply in practice an algorithm and measurement module that can measure and evaluate tool wear using image processing technology. It focuses on determining the degree of wear by extracting the tool's outline, assessing its condition, and presenting the measured value to the operator.

• Journal of Navigation and Port Research
• /
• v.42 no.4
• /
• pp.277-282
• /
• 2018

Recently, the Vessel Traffic Service (VTS) coverage has expanded to include coastal areas following the increased attention on vessel traffic safety. However, it has increased the workload on the VTS operators. In some cases, when the traffic volume increases sharply during the rush hour, the VTS operator may not be aware of the risks. Therefore, in this paper, we proposed a new method to recognize ship movement anomalies automatically to support the VTS operator's decision-making. The proposed method generated traffic pattern model without any category information using the unsupervised learning algorithm.. The anomaly score can be calculated by classification and comparison of the trained model. Finally, we reviewed the experimental results using a ship-handling simulator and the actual trajectory data to verify the feasibility of the proposed method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.5
• /
• pp.82-91
• /
• 2014

The combined generator system by integrating several renewable energy sources can share the electrical infrastructure and therefore have the advantage of constructing not only the transmission system but also the power conversion system. Among the various combined renewable system, the wind power and wave power has a high possibility of future growth due to the economic feasibility in offshore environment. This kind of large-scale combined systems might be follow the determination by the transmission system operator's directions and control the output profile by focusing at PCC. However, both renewable energies are depend on the unpredictable environmental variation; it is needed to do the compensation devices. In this paper, the ESS compensation plan is proposed to do output determination of the combined generator system by paying attention to active power of utility grid with the analysis of the controllable elements of the wind and wave power generator. The improvement of the new application technique of the combined system is confirmed through using the PSCAD/EMTDC. The entire simulation process was designed by adopting the active power control according to the reference signal of TSO.

• Journal of the Ergonomics Society of Korea
• /
• v.27 no.1
• /
• pp.37-43
• /
• 2008

A lot of models have been developed for prevention of human errors. Nevertheless most of them failed to attract attention of industry which has been looking for an integrative model that can show practical countermeasures as well as causal factors of human errors. This research aimed to develop a comprehensive model that can mainly be applied to industrial fields. Therefore, in the model, it was tried to explain sequences of an operator's information process that might cause human errors on one hand, and life cycle stages of facilities involved when human errors occur on the other hand. This model was validated by using a typical accident case. With the comprehensive model presented in this research, one could follow up the sequence of human errors caused by operators, and errors made at the design stage which might cause accidents could be tracked. As a consequence, it is expected that much attention would be paid to preventing human errors in industrial fields since safety personnel can easily find out cause of human errors throughout life cycle stages of man-machine facilities if utilizing the suggested model.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.8
• /
• pp.53-62
• /
• 1995

In recent years, the rapid development of the machine tool and tough insert has made metal removal rates increase, and automatic system without human supervision requires a higher degree reliability of machining process. Therefore the control of chips is one of the important topics which deserves much attention. The chip classification was made based upon standard deviation of the mean cutting force measured by a tool dynamometer. STS304was chosen as the workpiece which is known as the difficult-to-cut material and mainly saw-toothed chip produced, and the chip type according to the standard deviation of mean cutting force was classified into five categories in this experiment. Long continuous type chip which interrupts the normal cutting process, and damages the operator, tool and workpiece has low standard deviation value, while short broken type chip, which is favourable chip for disposal, has relatively large standard deviation value. In addition, we investigated the possibility that the chip type can be predicted analyzing the relationship between chip type and cutting condition by the trained neural network, and obtained favourable results by which the chip type can be predicted with cutting conditon before cutting process.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.10 no.1
• /
• pp.57-61
• /
• 1980

In dental roentgenograph it is of mutual benefit to the patient and the dentist to use the minimum amount of radiation capable of producing roentgenograms with maximum interprtive informations. Recent increases in the number of diagnostic x-ray examinations made in this country have caused attention to be paid to the quantity of radiation delivered to the population and operator. The purposes of this study was to assess the quality of dental x-ray units, the amount of films, the average processing procedures and the radiation protection methods in korea. The results were as following: 1. Most of radiation generating system were used in low voltage such as 60Kvp, 10㎃. 2. High sensitivity films such as 'D' group of Kodak or Rinn were mainly used and average 14.7 films used per weeks. 3. Some dentists practiced visual processing technic in simple dark room, and others used instant films. 4. 68.26% of patient held the film themselves, but 27.30% were assisted by dentists film holding. 5. In radiation protection method, 7.85% of dentists had protection equipments such as protective barrier, 2.73% wore protective apron, 27.9% made it a rules to avoid beam, and 7.51% used to maintain a distance from the radiation source.

• Advances in nano research
• /
• v.12 no.2
• /
• pp.213-221
• /
• 2022

Silicon carbide (SiC) is a binary carbon-silicon compound. In its two-dimensional form, monolayer SiC is composed of a monolayer carbon and silicon atoms constructed as a honeycomb lattice. SiC has recently been receiving increasing attention from researchers owing to its intriguing electronic properties. In this present work, SiC nanoribbons (SiCNRs) are modelled and simulated to obtain accurate electronic properties, which can further guide fabrication processes, through bandgap engineering. The primary objective of this work is to obtain the electronic properties of monolayer SiCNRs by applying numerical computation methods using nearest-neighbour tight-binding models. Hamiltonian operator discretization and approximation of plane wave are assumed for the models and simulation by applying the basis function. The computed electronic properties include the band structures and density of states of monolayer SiCNRs of varying width. Furthermore, the properties are compared with those of graphene nanoribbons. The bandgap of ASiCNR as a function of width are also benchmarked with published DFT-GW and DFT-GGA data. Our nearest neighbour tight-binding (NNTB) model predicted data closer to the calculations based on the standard DFT-GGA and underestimated the bandgap values projected from DFT-GW, which takes in account the exchange-correlation energy of many-body effects.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.16 no.11
• /
• pp.3565-3583
• /
• 2022

The task scheduling problem has received a lot of attention in recent years as a crucial area for research in the cloud environment. However, due to the difference in objectives considered by service providers and users, it has become a major challenge to resolve the conflicting interests of service providers and users while both can still take into account their respective objectives. Therefore, the task scheduling problem as a bi-objective game problem is formulated first, and then a task scheduling model based on the bi-objective game (TSBOG) is constructed. In this model, energy consumption and resource utilization, which are of concern to the service provider, and cost and task completion rate, which are of concern to the user, are calculated simultaneously. Furthermore, a many-objective evolutionary algorithm based on a partitioned collaborative selection strategy (MaOEA-PCS) has been developed to solve the TSBOG. The MaOEA-PCS can find a balance between population convergence and diversity by partitioning the objective space and selecting the best converging individuals from each region into the next generation. To balance the players' multiple objectives, a crossover and mutation operator based on dynamic games is proposed and applied to MaPEA-PCS as a player's strategy update mechanism. Finally, through a series of experiments, not only the effectiveness of the model compared to a normal many-objective model is demonstrated, but also the performance of MaOEA-PCS and the validity of DGame.

• Journal of Korean Home Economics Education Association
• /
• v.29 no.2
• /
• pp.1-22
• /
• 2017

The purpose of this research is to share the experience of reflective practice of a Home Economics teacher professional learning community(PLC) operator and to share better suggestions through reflection on PLC operation. All conversation in the 18 sessions of the PLC totally from May 31st 2013 to May 19th 2014 was recorded and transcribed. All materials of PLC activity were qualitatively analysed. Its themes were grounded on its coding and categorization scheme. Findings and conclusions of this study are as followings. The experience of learning the PLC for a year has found that it is the power to keep the PLC alive: courage and anxiety to face anxiety and anxiety about new challenges, the importance of theme selection, a teacher with a reckless challenge, shares of becoming a leader. Through reflection, I learned that concerns require attention to other teachers and the need for a 'New Round' for ongoing meetings. I, as a operator, did not fully consider participant's different interest as well as a program for a new round due to the lack of management experience. It led to the low participations in latter sessions of PLC. Suggestions are put as solutions to improve these problems; (1) grouping participants by school levels when collecting participants, (2) setting operation period and program applying participants' opinions, and (3) operating short-term PLC with certain themes to immerse reaching goal and satisfaction in short time.