• Journal of Korean Society of Water and Wastewater
• /
• v.20 no.5
• /
• pp.667-676
• /
• 2006

This study was conducted to evaluate the effect of longitudinal baffle on hydrodynamic behavior within a certain full-scale sedimentation basin (flow rate per basin; $1,000m^3/d$). Comparative experimental investigations have been carried out on the sediment removal efficiencies and the sludge deposit distribution in the baffled and un-baffled sedimentation basin, respectively. From the results derived in the baffled and un-baffled sedimentation, the turbidity removal rate in the baffled sedimentation basin is about 38% higher than that in un-baffled. Also, the height of sludge deposit in the baffled sedimentation basin is approximately 20% lower, and the sludge concentration is 10% higher than those in un-baffled sedimentation basin. In order to explain the experimental results and investigate the effect of longitudinal baffle in more detail, we conducted Computational Fluid Dynamics (CFD) simulation. From the results of CFD simulation, the flow, especially in the near of outlet orifice, was more stable in the case of longitudinal baffled sedimentation basin than that in un-baffled basin. Also, it could be concluded that the longitudinal baffle made a fully developed flow more effective for sedimentation.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.677-684
• /
• 2016

This study was carried out to confirm the effects of the knife-incising and longitudinal kerfing treatment on high-temperature drying characteristics of red pine square timber with dimensions of thickness 15 cm. The range of final moisture content was investigated 5.6% to 7.5% after drying. The differences did not exist in the moisture content and distribution according to the pretreatment condition. In the case of longitudinal kerfing treatment, the surface check occurrence was reduced than the control. In addition, the twist had a tendency to decrease due to the longitudinal kerfing treatment. The knife-incising and longitudinal kerfing treatment were investigated to be ineffective on internal checks and drying shrinkage.

• International Journal of Computer Science & Network Security
• /
• v.21 no.4
• /
• pp.52-58
• /
• 2021

Questionnaires and surveys are increasingly being used to collect information from participants of empirical software engineering studies. Usually, such data is analyzed using statistical methods to show an overall picture of participants' agreement or disagreement. In general, the whole survey population is considered as one group with some methods to extract varieties. Sometimes, there are different opinions in the same group, but they are not well discovered. In some cases of the analysis, the population may be divided into subgroups according to some data. The opinions of different segments of the population may be the same. Even though the existing approach can capture the general trends, there is a risk that the opinions of different sub-groups are lost. The problem becomes more complex in longitudinal studies where minority opinions might fade over time. Longitudinal survey data may include several interesting patterns that can be extracted using a clustering process. It can discover new information and give attention to different opinions. We suggest using a data mining approach to finding the diversity among the different groups in longitudinal studies. Our study shows that diversity can be revealed and tracked over time using the clustering approach, and the minorities have an opportunity to be heard.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.2
• /
• pp.315-319
• /
• 2022

This study investigates longitudinal writing development in terms of syntactic complexity using linear mixed effects (LME) model. This study employs essays written by four case study participants. Participants voluntarily wrote essays outside of the classroom and submitted the first and second drafts, after reflecting on the automated writing evaluation feedback (i.e., Criterion) every month over one year. A total of 48 first drafts were analyzed and syntactic complexity features were selected from Syntactic Complexity Analyzer. Results of LME showed that there was a significant positive linear relationship between time and mean length of T-unit and also between time and the ratio of dependent clauses to independent clauses, indicating that case study participants wrote longer T-units and also a higher proportion of dependent clauses over one year.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.591-596
• /
• 2001

In case of continuous steel box-girder bridges, the magnitude of the longitudinal tensile stress on concrete in internal support is larger than the tensile strength of concrete. In this paper, the parametric study was performed to present the effective magnitude of the longitudinal prestress for reducing the longitudinal tensile stress to decrease under the tensile strength of concrete. The parametric study is conducted with changing the steel box-girder section and the span length of bridge. Three dimensional finite element analyses are conducted with ABAQUS program. The behavior of the steel box-girder bridge with prestress is investigated through experimental works on a analogous steel box-girder bridge model, and their results are compared with those of analytical studies.

• Transactions of Materials Processing
• /
• v.8 no.2
• /
• pp.208-215
• /
• 1999

To increase rolling yields by minimizing trimming losses of hot-rolled plate, optimization logic for the edger model has been developed. The logic to determine optimum edging amount model has been formulated on the basis of actual production rolling data. In case of broadside rolling, the fish tail shape at the sides of plate was better for reducing the crop loss and this could be achieved when the edging amount of broadside rolling was increased. At a given broadside rolling ratio, methodology to determine optimum edging amount for the finish rolling which could minimize the width deviation of plate were systematically derived. Therefore, for a given broadside rolling condition and the permissible tolerance in width deviation of plate, it was possible to optimize the edging amount in finish rolling to maximize rolling yields. The application of optimization logic in this study increased rolling yields from approximately 10% to 30% at various longitudinal eding raitos.

• International Journal of Computer Science & Network Security
• /
• v.24 no.3
• /
• pp.201-210
• /
• 2024

In empirical software engineering research, there is an increased use of questionnaires and surveys to collect information from practitioners. Typically, such data is then analyzed based on overall, descriptive statistics. Overall, they consider the whole survey population as a single group with some sampling techniques to extract varieties. In some cases, the population is also partitioned into sub-groups based on some background information. However, this does not reveal opinion diversity properly as similar opinions can exist in different segments of the population, whereas people within the same group might have different opinions. Even though existing approach can capture the general trends there is a risk that the opinions of different sub-groups are lost. The problem becomes more complex in case of longitudinal studies where minority opinions might fade or resolute over time. Survey based longitudinal data may have some potential patterns which can be extracted through a clustering process. It may reveal new information and attract attention to alternative perspectives. We suggest using a data mining approach to finding the diversity among the different groups in longitudinal studies (agile skeptics). In our study, we show that diversity can be revealed and tracked over time with the use of clustering approach, and the minorities have an opportunity to be heard.

• Journal of Korean Neurosurgical Society
• /
• v.49 no.1
• /
• pp.8-12
• /
• 2011

Objective: Ossification of the posterior longitudinal ligament (OPLL) has a strong genetic component. Specific gene polymorphisms may be associated with OPLL in several genes which regulate calcification in chondrocytes, change of extracellular collagen matrix and secretions of many growth factors and cytokines controlling bone morphogenesis. Toll-like receptor 5 (TLR5) may playa role in the pathogenesis of OPLL by intermediate nuclear factor-kappa B (NF-${\kappa}B$). The current study focused on coding single nucleotide polymorphisms (SNPs) of TLR5 for a case-control study investigating the relationship between TLR5 and OPLL in a Korean population. Methods: A total of 166 patients with OPLL and 231 controls were recruited for a case-control association study investigating the relationship between SNPs of TLR5 gene and OPLL. Four SNPs were genotyped by direct sequencing (rs5744168, rs5744169, rs2072493, and rs5744174). SNP data were analyzed using the SNPStats, SNPAnalyzer, Haploview, and Helixtree programs. Multiple logistic regression analysis with adjustment for age and gender was performed to calculate an odds ratio (OR). Results: None of SNPs were associated with OPLL in three alternative models (codominant, dominant, and recessive models; p> 0.05). A strong linkage disequilibrium block, including all 4 SNPs, was constructed using the Gabriel method. No haplotype was significantly associated with OPLL in three alternative models. Conclusion: These results suggest that Toll-like receptor 5 gene may not be associated with ossification of the posterior longitudinal ligament risk in Korean population.

• The Journal of Engineering Geology
• /
• v.26 no.3
• /
• pp.393-401
• /
• 2016

In the present study, fault attitudes and the locations of appearance of faults in tunnel faces were predicted by analyzing the trajectory of the maximum longitudinal displacement immediately before the appearance of faults through three-dimensional finite element analysis. A total of 28 fault attitude models were used in the analysis. Those faults that have drives with dip appear first in the upper part of tunnel faces as tunnel excavation progresses and their maximum longitudinal displacement shows a tendency to move from the middle part to the upper part of tunnel faces. Those faults that have drives against dip appear first in the lower part of tunnel faces as tunnel excavation progresses and their maximum longitudinal displacement shows a tendency to move from the middle part or middle upper part to the lower part of tunnel faces. In addition, when the dip of faults is larger the maximum longitudinal displacement moves from the left upper part toward the wall part in the case of drive with dip models and from the left lower part toward the wall part in the case of drives against dip models. Therefore, it was indicated that the attitudes of faults distributed ahead of tunnel faces and the locations where faults appear in tunnel faces can be predicted by analyzing the longitudinal displacement trajectory of tunnel faces following excavation.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2009.09a
• /
• pp.65-70
• /
• 2009

In case that tug boat pushes side structures of other large vessels to maneuver, it is required that contacted side structures of the maneuvered vessels have enough structural safety against tug push loads. The objective of this study is to evaluate the structural effect of carling which is installed between side longitudinal stiffeners. A comparative study of side structures with carling and without carling is performed to evaluate the effect of carling member by both FE analysis. According to the result, it is found that the carlings play effective role in the strength of side plates and side longitudinal stiffeners against tug push loads.